Question about 2011 Harley Davidson FLHR Road King

1 Answer

Kickstand fell off on a road king and not sure how it goes back

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

To replace the 2011 Touring jiffy stand leg FIRST support the motorcycle with a suitable lifting device so it securely upright and level and the jiffy stand is able to move through its full range of travel, move the jiffy stand to the full forward or down position, remove the hex bolt,the lockwasher, the flat washer and the leg stop, swing the jiffy stand forward beyond the normal down position and remove the end of the spring from the jiffy stand, remove the leg from the bracket, remove the other end of the spring from the frame weldment, inspect all of the parts for wear/damage and replace if and as necessary. TO install the leg FIRST apply SILVER GRADE ANTI-SEIZE compound to the area of the leg that rotates within the bracket, verify that the end of the spring enters the hole from the front of the leg weldment because if the end of the spring enters the hole from the rear of the weldment the spring coil will rub on the leg when in use, install the end of the spring into the hole in the frame weldment, insert the leg up through the bracket, swing the jiffy stand forward beyond the normal down position and install other end of the spring into the hole in the leg weldment. Be careful to install the leg correctly because if it is installed incorrectly excessive wear can occur which will allow the vehicle to fall when rested on the jiffy stand. THEN holding the leg at the normal forward (down) position, install the stop over the threaded end with the stamped side down, verify that the longer side of the stop faces the rear of the motorcycle, install the flat washer, the lockwasher and the hex screw and tighten it to 15-20 ft-lbs (20.3-27.1 Nm), extend and retract the jiffy stand several times to verify proper operation, freely swinging to both the fully extended and the fully retracted positions, move the jiffy stand to the full forward (down) position and remove the lifting device and let the motorcycle rest on the jiffy stand, verify that the rubber stop is installed in the hole of the jiffy stand weldment to prevent damage to the painted finish.

To remove the 2011 touring jiffy stand bracket FIRST lift and support the motorcycle in a fully upright position off of the jiffy stand, remove the left rider footboard and support brackets, remove the jiffy stand leg, remove the two fasteners and the lockwashers to release the jiffy stand bracket from the frame weldment.

To Install the 2011 touring jiffy stand bracket FIRST install the two fasteners and lockwashers to secure the front of the bracket to the frame weldment, temporarily install the footboard rear fastener to align the rear of the jiffy stand bracket but do not tighten it, tighten the front fasteners to 36-42 ft-lbs (48.8-57.0 Nm), install the footrest and install the jiffy stand leg.

Posted on Oct 15, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wd4ity
  • 4565 Answers

SOURCE: the spring on the kickstand

Have someone hold your bike up straight while you operate the kick stand. Find the point at which the spring has the least amount of stretch to it. Hook the spring on the frame and use a spring hook or a pair of side cut pliers to stretch the spring onto the kickstand at this point. If the spring hook on the frame is held on by bolts, you can loosen the bolts but don't take the completely off to shorten the stretch. That's the way I've always done it. Just make certain you get the correct spring.

Good Luck
Steve

Posted on Apr 22, 2011

wd4ity
  • 4565 Answers

SOURCE: kickstand fell off and not sure how it goes back

Go to http://www.bikebandit.com and Click OEM parts and choose your bike or one close to it to get a diagram of how the kickstand goes on.

Good Luck
Steve

Posted on Jun 05, 2011

  • 11 Answers

SOURCE: 2008 Road King won't start in gear

neutral safety switch...

Posted on Apr 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kick stand fell off while riding. Not sure of all that was lost or how it goes back on. Any suggestions?


Hi Steve, Well hopefully not much, look underneath frame and see whats left, here is a complete list of parts. Anchor plate held to the frame by a bolt that screws into a threded spacer, a solid pin, cotter pin and washer . Then there is the kickstand and its bumper witch is held in place by a bolt, a catch, and a pivot block. A kickstand spring that attaches to the anchor plate at one end the other end goes to the kickstand. Good luck

Mar 25, 2015 | 2007 Harley Davidson FXDC Dyna Super Glide...

1 Answer

Bike will not stay running


(1) harley vibrates make sure kickstand stays up.
(2) you have to find it. there is a tilt switch on bike.
if it lean over to far it will kill the bike. check to see if its ok.

Apr 21, 2014 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

My transmission on my 2001 flhrci suddenly started leaking. don't notice leakage when bike is upright


Clean all oil from the bike exterior. Leave it sitting in an upright position for a period of time. This may require a bike lift or other such device. Then look for leak source. Make sure oil level is not too high. When changing oil it often gets on the cross member and may leak when on the jiffy satnd for a while until it is all gone from this area. Make sure to always use thread sealant and a good o-ring on the drain plug.

Jun 23, 2012 | 2001 Harley Davidson FLHRCI Road King...

1 Answer

Kickstand fell off and not sure how it goes back on. do you have a picture/breakdown of the installation?


Go to http://www.bikebandit.com and Click OEM parts and choose your bike or one close to it to get a diagram of how the kickstand goes on.

Good Luck
Steve

Jun 05, 2011 | 2008 Harley Davidson FXDSE CVO Screaming...

1 Answer

How to attach kick stand spring on 2006 road glide


Take the bolt out of the kickstand, attach the spring, then use the kick stand for leverage to stretch the spring, and re-install the bolt...

Apr 10, 2010 | 2006 Harley Davidson FLHR Road king

Not finding what you are looking for?
2011 Harley Davidson FLHR Road King Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...