Question about 2001 Harley Davidson FXD Dyna Super Glide

1 Answer

Changing/replacing battery in FXDX Superglide Sport, year 2001

I know how to remove the seat.
I can disconnect cables including ground wire.
I just can't seem to figure out how to remove the battery from the tray.

Posted by on

  • Anonymous Mar 23, 2014

    My battery is dead when try to remove it alarm goes off how do you stop this please and candy manually do it as don't know pin or know how to get pin thanks

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Harley Davidson Expert
  • 284 Answers

You have 2 bolts on the left side of the tray one you can see just by looking at it. the other is right above it facing down

Posted on Jun 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spark plugs for 2000 FXDX Harley dyna superglide sport


Hi Anonymous, the HD 6R12 spark plug is gapped at .040" Have nice day.

Jun 20, 2012 | 2000 Harley Davidson FXDX Dyna Super Glide...

1 Answer

How to test a coil on a 2005 Harley Davidson superglide


Hi Luv2dad, remove coil, with an ohm meter check primary resistance at the terminal ends, reading should be 0.5 to 0.7 ohms.
Then check secondary resitance at spark plug cable towers, reading should be 5500 to 7500 ohms. Good luck

Mar 09, 2012 | 2003 Harley Davidson FXDX Dyna Super Glide...

1 Answer

How to remove starter from 2008 dyna lox rider . I have already un bolted it and removed wires but it is loose but will not come out yet .


Instructions
  1. Removal
    • 1 Remove the seat retainer screw from the seat mounting bracket using a ratchet and Allen driver. Lift the rear of the seat up and slide the seat toward the rear of the bike to disengage the seat from the frame and remove it from the bike.
    • 2 Don a face shield and rubber gloves.
    • 3 Remove the battery cover retaining screw from the bottom of the battery cover using a ratchet and Allen driver. Tilt the top of the battery cover out and lift the cover to disengage it from the battery tray.
    • 4 Remove the negative battery cable from the battery using a 10 mm wrench.
    • 5 Remove the positive battery cable from the battery using a 10 mm wrench.
    • 6 Unhook and remove the battery strap. Remove the battery from the tray. Remove face shield and rubber gloves.
    • 7 Remove the two top battery tray screws from the frame above the battery tray and the bottom battery tray screw from the inside of the battery tray using a ratchet and Allen driver.
    • 8 Remove the battery tray from the bike while guiding the battery cables through the holes in the battery tray.
    • 9 Remove the starter end-cover nut, using a ratchet and socket, and pull the end-cover off the starter.
    • 10 Pull back the protective rubber boot off the positive cable terminal. Using a wrench, remove the positive cable nut and then lift the ring terminal off the starter terminal stud. Unplug the solenoid electrical connector from the solenoid.
    • 11 Remove the two starter retaining bolts from the starter using a ratchet and Allen driver. Pull the starter off the bike. Remove and discard the starter housing O-ring.
    Installation
    • 12 Inspect the two split-ring bushings in the inner primary case where the starter mounts for slack or looseness. Remove the split-ring bushings and spread them to provide a slight interference fit in the primary housing. Push the split-ring bearings back into position.
    • 13 Install a new starter housing O-ring on the starter assembly. Install the starter assembly on the bike.
    • 14 Apply one drop of Loctite Threadlocker 243 to the treads of the starter retaining bolts. Install the starter retaining bolts and washers and tighten them to 24 to 27 foot-pounds using a foot-pound torque wrench and Allen driver.
    • 15 Install the positive cable ring terminal and nut on the starter terminal stud. Tighten the nut to 65 to 85 inch-pounds using an inch-pound torque wrench and socket. Push the protective boot securely over the positive cable terminal. Plug the solenoid electrical connector into the solenoid.
    • 16 Position the starter end-cover on the starter and install the nut, using a ratchet and socket.
    • 17 Place the battery tray in position while guiding the battery cables through the holes in the tray.
    • 18 Install the upper and lower battery tray screws and washers. Tighten the screws to 96 to 120 inch-pounds, using an inch-pound torque wrench and Allen driver.
    • 19 Guide the battery cables into the recesses at the upper corners of the battery tray.
    • 20 Don face shield and rubber gloves.
    • 21 Place the battery in the battery tray with the terminals facing out. Snap the battery strap in position.
    • 22 Install the positive battery cable and cable bolt. Tighten the bolt to 60 to 70 inch-pounds using an inch-pound torque wrench and socket.
    • 23 Install the negative battery cable and cable bolt. Tighten the bolt to 60 to 70 inch-pounds, using an inch-pound torque wrench and socket.
    • 24 Remove the face shield and rubber gloves.
    • 25 Apply a light coat of corrosion retardant grease or petroleum jelly to the terminals.
    • 26 Install the battery cover and screw. Tighten the screw securely using a ratchet and Allen driver.
    • 27 Place the seat on the bike. Lift the rear of the seat and slide it forward to engage the seat tab in the frame slot. Lower the rear of the seat and install the seat retainer screw through the seat mounting bracket. Tighten the seat retainer screw securely using a ratchet and Allen driver. Lift up on the seat to make certain that it is mounted securely on the bike.

Nov 18, 2011 | 2008 Harley Davidson FXDL Dyna Low Rider

1 Answer

I HAVE A 2001 AURORA. SEEMS TO HAVE A GROUND PROBLEM SOMEWHERE. HIT A BUMP IN THE ROAD ALL LIGHTS WENT OUT. LOST POWER STEERING THEN THE CAR QUIT. STARTED LATER AND EVERY THING IS FINE. HAVE NOTICED...


clean your battery terminals-lift the rear seat, the battery is under the passenger seat, disconnect the terminals (both), use a wire brush and get the cable lugs shiny on the inside, where they clamp onto the battery terminals. Then clean the battery posts, hoop up the positive cable first, then the negative cable-while you are there, look at the negative cable and make sure it other end is tight and not rusted where it connects to the body.

Mar 21, 2011 | 2001 Oldsmobile Aurora

1 Answer

Where is computer located under dash / how to replace?


SECTION 303-14: Electronic Engine Controls 2001 Explorer Sport/Sport-Trac Workshop Manual REMOVAL AND INSTALLATION Powertrain Control Module (PCM) Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Disconnect the powertrain control module (PCM) electrical connector. I believe it is on the firewall on the passenger side of truck.
  1. Remove the nuts and the PCM cover.
  1. Remove the PCM. I believe it comes out under the dash. Not sure.
  1. To install, reverse the removal procedure.

Feb 02, 2011 | 2001 Ford Explorer Sport

1 Answer

I need to remove battery from my dyna sport fxdx 2002 , the cover up is fixed with the bolt of cable battery ? it's so difficult to remove the bolt on cable someone can help me ?


On the older models this is how you remove the battery. I doubt Harley has changed much but if they did, this may help.

Remove the seat. Just behind the battery between it and the rear fender on the right side of the bike, there are two bolts. Loosen the bolts but don't take them out. Look inside the frame behind the battery and you'll see a "jack bolt". Turning the bolt counterclockwise will lower the battery tray allowing you to get the top cover and surrounding cover off. Then you can get to the battery connections easily.

I hope this helps.

Ride Safe
Steve

Jan 03, 2011 | 2002 Harley Davidson FXDX Dyna Super Glide...

1 Answer

Battery removal 2002 dyna super glide, after seat removed.


Just inside the frame from the battery, there's a "jackbolt" that raises and lowers the battery tray. Turning the bolt counterclockwise lowers the battery tray and vice versa. You must loosen two bolts on the right side of the frame just behind the battery box between the battery box and the rear fender. Once the battery is lowered, you'll be able to get the top cover off and disconnect the battery cables. Disconnect the negative first when taking the battery out. Connect the negative last when installing the battery.

Good Luck
steve

Dec 05, 2010 | 2002 Harley Davidson FXDX Dyna Super Glide...

3 Answers

I need to know the location of the starter on a 1995,hyundai/sonata/4cyl2liter automatic,without having to pay.i don'thave credit card.


206c28c.jpg

Fig. 1: The starter is mounted to the transaxle bell housing and is easily accessible from the top side of the engine compartment

Hope helps (remember rated this).

Jun 05, 2010 | 1995 Hyundai Sonata

1 Answer

I have a 2001 cavalier with a dim driver side headlight. Have changed the bulb, DRL relay and headlight switch. Removed the ground cable from the battery tray, cleaned ground cable and battery tray contact...


Give this a try------get a piece of wire and strip both ends, the black wire coming out of the plug on the head light, stick one end of the wire in there and the other end to a good ground or the negative battery terminal with the lights on, if the light gets brighter, there is a bad ground to that light. I hope this helps, cause you have just done about everything else.

May 15, 2010 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
2001 Harley Davidson FXD Dyna Super Glide Logo

640 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...