Question about Harley Davidson FLHR - FLHRI Road King Motorcycles

1 Answer

Why does my starter stay engaged unless I pull the wire going to starter on my harley roadking

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Harley Davidson Expert
  • 438 Answers

Bad starter solenoid possibly

Posted on Jan 05, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: starter wiring for 1340cc harley motor

the posative wire from the soleniod had worn a hole in the insulation and was arking to the soleniod cover plate,and welded itself to the cover. i reinsulated it with shrinktube and fixed that,but with that the starter will not engage now. i'm going to attempt to rebuild the starter.

Posted on Mar 24, 2009

  • 5 Answers

SOURCE: have harley flst wont go in neutral unless you

Sounds like you need to adjust the clutch or replace. You don't mention how many miles or if the clutch has been serviced.

Posted on Aug 04, 2009

wd4ity
  • 4565 Answers

SOURCE: how do you remove a starter on a 04 harley daidson

You're going to have to remove a lot more than that. You've got to remove the outer primary cover to get to the jackshaft. The jackshaft has a long bolt in it with a bend tab washer to hold it in place. Remove the bolt. You may can pull the starter out then there is a "coupling" that connects the starter and the jackshaft. It has to go in in a particular way. Make sure you identify which way this coupling has to be in there. It has a snap ring on the inside of it.

With that off, you may be able to get your starter off. I have seen them where you had to remove the clutch assembly by an inch or so to get the starter out. Of course, everything on the right side of the bike that gets in the way of the starter must come off as well.

Good Luck, Steve

Posted on May 06, 2010

Testimonial: "thanks bro...but its just a starter,lol"

wd4ity
  • 4565 Answers

SOURCE: DO YOU HAVE TO PULL THE PRIMARY TO REMOVE THE

yes, you have to take the bolt out of the jackshaft.

Steve

Posted on Jul 25, 2010

Testimonial: "THANK YOU FOR THE HELP."

wd4ity
  • 4565 Answers

SOURCE: 2003 roadking starter when reinstalling starter

I think the spring you're talking about is the one on the Jackshaft. It goes on the jackshaft on the primary side of the collar. Go here and have a look. www.bikebandit.com
http://www.bikebandit.com/2003-harley-davidson-touring-road-king-flhr/o/m18451#sch614257

Good Luck
Steve

Posted on Jul 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 roadking wont go into gear and starter just spins'


The starter clutch needs to be replaced. An alternator sgop will usually rebuild these for 1/2 of a new one.
.A thumbs up would be greatly appreciated if this answer is helpful to you. 97-roadking-wont-go-into-gear-starter-4d5i0utctl2htkxwobhufr12-1-0.jpg

Mar 26, 2014 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

Harley starter


Hi Anonymous, get out your test light and check the start button for continuity if ok track the wiring to the starter relay and solenoid your contacts could be welded, for a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

May 01, 2013 | 2006 Harley Davidson FXSTDI Softail Deuce

1 Answer

How do you remove a starter on a 04 harley daidson roadking . ive got the 2 bolts that hold it in out,ive got the wires off.it looks like you have to remove the oil fill neck?


You're going to have to remove a lot more than that. You've got to remove the outer primary cover to get to the jackshaft. The jackshaft has a long bolt in it with a bend tab washer to hold it in place. Remove the bolt. You may can pull the starter out then there is a "coupling" that connects the starter and the jackshaft. It has to go in in a particular way. Make sure you identify which way this coupling has to be in there. It has a snap ring on the inside of it.

With that off, you may be able to get your starter off. I have seen them where you had to remove the clutch assembly by an inch or so to get the starter out. Of course, everything on the right side of the bike that gets in the way of the starter must come off as well.

Good Luck, Steve

May 06, 2010 | 2004 Harley Davidson FLHR - FLHRI Road...

1 Answer

97 fatboy starter engages but will not stay engaged.


I would check the starter clutch its self first. It is a one way clutch so if you remove the starter and disassemble it to the starter clutch and hold the starter clutch in one hand and use your other hand to turn the starter clutch gear, it should only turn in one direction.

Mar 30, 2009 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

Starter Stays Engaged


check the wire that is hooked to the starter wire on the car. it should only show pwer in the start posision

Nov 19, 2008 | AutoCommand Remote Car Starter Add-On

3 Answers

Starter won't engage


better yet...............even if you have the minimun 12.5 volts on the battery, the amps may not be suffiicent to turn the starter and you will hear a clacking noice. the battery probably needs to be replaced.

Sep 04, 2008 | Harley Davidson Harley-Davidson Motorcycle...

2 Answers

What going on


Bad switch or Solenoid. depending on the bike.

Mar 17, 2008 | Harley Davidson Harley-Davidson Motorcycle...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...