Question about 2003 Yamaha YZ 125

1 Answer

When start go to rev it just dies

When i start the bike up it wont idle by itself and will cut out, so try again and again and the bike will fire up so i try to rev it up and it will die,almost like its getting flooded but its not or like its not getting enough gas all the stuff ive tryed just dosnt work ive cleaned out carb clean all the exhaust tipped out old gas cleaned fuel filter and lines.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Remove the throttle stop adjuster and the air screw adjuster and spray carb cleaner in the holes.
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Turn the pilot screw 1/4 turn counter clockwise. Check the float level. Before putting the slide back in the throat of the carb, move the clip on the jet needle one notch lower.Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Adjust the idle speed with the Throttle stop screw. This process should get you back on the road. A “very helpful” rating for this answer? Thanks!


when start go to rev it just dies - 65c15ea.gif

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont idle or run for long


clean the carbs out ! tank too !

Mar 26, 2014 | 2005 Suzuki GSX-R 750

1 Answer

Tickover problem on beta 125 rev 3


Hi, Anonymous and the usual suspects are:
1. Idle speed improperly adjusted.
2. Inlet system air leak.
3. Leaking accelerator pump.
4. Loose low-speed jet.
5. Plugged low-speed jet.
6. Contaminated or plugged low-speed circuit.
7. Enrichner valve is not seated or leaking.
For more information about your issue please visit the websites below. Good luck and have nice a day.
How to Adjust Idle On Dirt Bike Tips and Tricks 1
How to adjust your idle
How to fix dirt bike that wont idle
http://www.lewisportusa.com/manuals.htm
http://www.betamotor.com/en/support/manuals


Nov 30, 2013 | 2006 Beta Rev3 125

1 Answer

Motorbike wont move


sidestand lockout switch is sticking...bike thinks that you're trying to ride away with the stand down so it kills the sparks.

Mar 25, 2013 | kawasaki GPZ 500 S - GPX 500 R Motorcycles

1 Answer

Hi, my zzr 250 hadn't been started for about 8 months, so it fired up nicely with the choke on but once the bike warmed up I couldn't get it to idle once the choke was off, i tried more air to the carby...


Could be one of two things
1. The carbs are gummed up. Modern fuel will break down after only a few months. The idle jets are quite small and will easily become blocked. Strip and clean the carbs.
2. The throttle cable is sticky. Less likely, but possible. Make sure it opens and snaps shut easily.
What do you mean when you say you tried more air?

Aug 04, 2010 | 1991 kawasaki ZZR 250

1 Answer

My ZXR 400 is cutting out when given throttle


Dont know if you have solved it but check your stand cut switch maybe loose

Jul 18, 2010 | 1993 kawasaki ZXR 400

2 Answers

Wont start.


Hi, Sounds like a sticky float valve in one or more of the carbs. When sitting, the carb overfills causing the revving when you start it, then it dies cause the carb isn't filling. Also check the exup valve in the intake, it could also cause the exact same symptoms but because of too much back pressure once it starts. Good Luck to you, hope this helps Fixya!

Mar 24, 2009 | 1992 Yamaha FZR 600

2 Answers

FXR suzuki 150 will idle but wont rev


i had the same problem ! i dont know how but there was water mxit in my tank and i dumpd the fuel then it was fine

Mar 16, 2009 | 2001 Suzuki FXR 150

1 Answer

1994 mustang gt cuts out


have you been tuning it? look for the vacuum hose you knocked off.

Mar 01, 2009 | 1994 Ford Mustang

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

1,242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...