Question about 1981 kawasaki Csr 1000

1 Answer

Clutch Cable Snapped

Show Me How To Install Clutch Cable

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Hook the cable on the case lever then route the cable to the clutch handle. Turn the adjuster lock wheel all the way to the outer end of the adjuster then turn the adjuster all the way into the lever mount. This makes the adjuster as short as possible. Line up the cut-outs in the adjuster and the lock wheel to the cut-out in the lever mount. Hook the end of the inner cable into the clutch handle. Now pull the outer casing of the cable to the end of the adjuster. If the cable end isn't long enough to slide into the end of the adjuster then put the end of the outer cable on the adjuster shaft at the lock wheel and pull the clutch lever in. Now quickly release the lever while pulling the outer cable to the end of the adjuster. Normally it will pop into place so you can set the clutch lever 1/4" end play. You may need to try it a few times until you get it.

A “very helpful” rating for this answer? Thanks!

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Old clutch cable snapped, tried replacing with new one, no pressure on the cable?


The first thing that comes to mind is that the new clutch cable is not the correct length (too long). Did you compare the old one with the new one? When you pull in the clutch lever you should be able to see the clutch release lever at the transmission move. If the lever is not moving then the cable is too long or needs adjustment.

Apr 24, 2014 | 2003 Suzuki GZ 125 Marauder

1 Answer

Clutch snapped


adjust cable at both ends

Feb 28, 2014 | 2007 BMW F 800 ST

1 Answer

How do I no if my clutch cable has snapped on my Renault laguana, my engine is running but won't go into any gear


check to see if the clutch pedal has a lot less pressure or has stayed in the down position if so it has , also see if you can put the car in gear with the engine turned off, if you can it sounds like it

Nov 20, 2012 | Cars & Trucks

1 Answer

My Nissan 95 sentra clutch had crunched and pedal would not spring back, found that clutch cable had snapped, replaced this and now my clutch pedal is still not 100% springing back, it springs back en


Check the spring to see if it has snapped anywhere within it's coil.

Remove the cable and check operation of the pedal and spring mechanism.
If all is well, then with a lever, check that the clutch release arm on the gearbox is operational. If that is also sticking, then you will have to remove the gearbox to investigate further.
If not sticking, then also remove the clutch cable outer sleeve, and replace.

Nov 10, 2012 | Cars & Trucks

1 Answer

I have a peugeot boxer 1.9d van and cant remove the clutch cable from out of bulk head, pedal side as it has snapped, do you have any ideas


If the cable has completely snapped and not attached to the clutch pedal, the whole cable, casing and broken cable should just about fall out of the bulkhead. I have never had a problem with that on any vehicle.

Apr 18, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

Clutch pedal went loose heard a snap just before ford fusion 2003


Hi
It sounds like your clutch cable has snapped, Or the pedal lever has snapped, can you still get gears?

if not then most likely thats the issue, clutch cable are fairly cheap about £30 ish fitted no more than £65

Hope this helps. if not get back to me with more info.

Regards
Dan

Feb 09, 2010 | 2004 Ford Fusion

1 Answer

Recently snapped my clutch lever off my kx 250


Be sure you were given the correct cable, The stock cable is part number 54011. Compair the old cable to the new one.

d9b88da.png

Aug 02, 2009 | 2003 kawasaki KX 125

3 Answers

How to relace clutch cable on 1995 saab se 900 turboon saab 900se


1. Remove the battery.
2. Remove the clutch cable end from the clutch arm end at the wire stop.
3. Slide out the rubber doughnut from the gearbox housing which holds the clutch cable
4. Move the distribution box nut and the alarm pin attached to it (some modules)
5. Disconnect the clutch cable holder from the fender and the data link holder.
6. Remove the drivers lower panel below the steering wheel and remove the air duct as well as the knee shield.
7. Slide out the fuse box holder and ICE Box (should be a black box with many wires going to it). You can remove the instrument cluster at this point but you can also do this without removing the cluster with a little patience
8. Move the pedal spring to one side and remove the eye catch for the cable.
9. Remove the clutch cable by pulling it out from the engine compartment
10. Reinstall in the reverse. Saab actually came out with a bulletin which Needed one to install two washers at the back of the new cable instead of one. The factory cable comes with one but you can remove the 2nd washer off the old cable and install it on the new cable so two exist. This helps take up excessive pedal slack.

Apr 22, 2009 | 1996 Saab 900

3 Answers

Clutch problems 88 porsche


the throw out bearing. Have to drop tranny to fix it.

Mar 13, 2009 | 1988 Porsche 911

1 Answer

Clutch cable, 1983 ford mustang


You've installed two cables, both of which broke. You made mention of a metal part bending, is this the fork? You may need to pull the bell housing to check the operation of the fork, throw-out bearing and pressure plate. This does not sound like a cable problem.

Aug 11, 2008 | 1983 Ford Mustang Hatchback

Not finding what you are looking for?
1981 kawasaki Csr 1000 Logo

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...