Question about 2001 Buell Blast

4 Answers

Changing oil on a buell blast

Not much oil is coming out and the dip stick still shows the same amount of oil on it.

Posted by on

  • kickbx_22 Jun 21, 2009

    there are 2 bolts on the bottom of the crank. The front one nothing came out and the rear one 3/4 of a quart. I'll check for obstruction thanks.

×

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Buell Expert
  • 473 Answers

Should be 1 quart in the primary side - only use the harley primary fluid as it has a syncro additive that keeps your syncronizers alive.

Posted on May 24, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Clutch tighting

Posted on Feb 11, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 40 Answers

There are 2 hoses on the inside left footpeg support; pull the plugs and drain there; 1 is crank breather other is oil tank

Posted on Jul 09, 2009

  • timothyjones Jul 09, 2009

    the 3/4 quart that drained from under the primary was probably primary fluid; make sure you refill that before you take off on the blast or you will need a new clutch pretty soon!

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,111 Answers

Try draining with the fill cap removed..ck the drain for an obstruction

Posted on Jun 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Dip stick for oil level not showing no oil present when oil is already present


consult the fluids and capacities section of the owners manual and verify that you have put in the listed amount of oil. If you are just trying to add oil, add a half qt at a time until it reads on the full line on the dipstick

Mar 01, 2015 | Cars & Trucks

1 Answer

Where do i look. place dip stick in shows oil .ride a distance pull dip stick show min.


Oil is not returning to the pan from the over head valve cover area.

Feb 11, 2015 | Cars & Trucks

1 Answer

How much oil what wt.


Most any kind of 4-cycle motor oil like 10W-30 will work in these motors. After draining the old oil replace the drain plug. There are two types of motor oil fill holes: 1. If you have a motor with the oil fill/check hole on the bottom of the motor and a small screw-in plug either with or without a small dip stick on it; with the motor level, fill the crank case with oil until it is up to the threads on the oil fill/check hole. 2. If you have a motor with a long dip stick that goes into a filler tube at the top of the motor, again with the motor level, put in about half a quart of oil and use the dip stick to check the oil level. If not full, add quarter quart amounts and check again until the oil is at the full mark on the dip stick. Do not overfill the crank case with oil. Most motors will take about one quart of oil but it varries so watch to see the oil level come up to the proper level.

Feb 03, 2011 | Porter Cable PorterCable DBSI325 3250 Watt...

1 Answer

2000 vw jetta 2.0 checked oil no oil showed on dip stick. saw that oil leaked into coolant system. replaced head gasket w/ new head bolts. flushed system, drained oil, new filter. after all done no oil...


Most likely place for oil into coolant is oil cooler, the aluminum box that mounts between the oil filter and a flange that comes off the block.

Jan 10, 2011 | 2002 Volkswagen Passat

2 Answers

How to check the oil. The dip stick has no method of measuring other than a small white knob on the end.


Done with scanner and it reads out oil level in mm. If oil level low, a warning with show on cluster.

Most modern vehicles measure oil level this way....as well as the transmission.

The Dip Stick tube is only for sucking out the oil. This is known as 'Top Side Evacuation'.

Some DIY types collect and measure the drained oil and refill with same amount.

Dec 23, 2010 | Bentley Continental GT Cars & Trucks

1 Answer

Dip stick showing white film. Oil change person


Water in motor oil causes that white foam, it is common. A small amount will not hurt the vehicle very much, and is normal for winter, in places with a high humidity.

Jan 05, 2010 | Chevrolet Colorado Cars & Trucks

1 Answer

I've owned a a 2000 Plymouth Grand Voyager for a year now. I change my own oil in it. Twice now, when I'm done and checking the dip stick for the oil level, the stick is bone dry! The first time this...


The van must be on level ground while checking. after adding the correct amount of oil making sure to prime the oil filter before installing run the van for approx 30 seconds turn off and recheck after 1 min.

Aug 03, 2009 | 2000 Plymouth Grand Voyager

1 Answer

I changed the oil but my dip stick is showing way too much oil, what is going on? At first I had a hell of a time getting the drain plug out, but finally did. Drained the oil, replaced the filter,...


Make sure you are not checking the oil with the car running first of all, second don't check the oil immediately after turning off the car let the engine stand for about ten minute allowing the oil to drain off the dip stick,

Jul 10, 2009 | 2001 Chevrolet Suburban

1 Answer

Crown vic oil change


Some of them have an oil plug at the front of the pan, as well as the regular one. You have to drain them both. The front one only holds a quart or less.

May 21, 2009 | 1990 Ford LTD Crown Victoria

Not finding what you are looking for?
2001 Buell Blast Logo

1,233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buell Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

jeepguy617

Level 1 Expert

41 Answers

Are you a Buell Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...