How do I change my odometer display from km to miles

There is no fuse for just the odometer, has main fuses for the whole instrument cluster . Odometer not working? instrument cluster problem. Have it checked by a professional repair shop.

Odometers
Each instrument panel cluster (IPC) is equipped with a season odometer and 2 trip odometers. The IPC uses the odometer rolling count message from the powertrain control module (PCM). The rolling count value is determined by counting the speed pulses from the vehicle speed signal (VSS). The IPC uses the rolling count data from the PCM and a software program to determine vehicle mileage. The odometers can be displayed in miles or kilometers. The units displayed is switched between English and metric by pressing the menu button on the driver information center (DIC) until the units mode is displayed. Pressing the set/reset button will select between English or Metric. . When the set/reset button is pressed to show the odometer in metric, km and the number will be displayed. When the odometer is in English, MI and the number will be displayed.


Season Odometer
The season odometer displays the total accumulated miles or kilometers of the vehicle. This value is permanently stored in the IPC. If an odometer malfunction occurs or if the IPC must be replaced, an authorized Delco service center must be contacted to program proper vehicle specifics, including mileage, for the IPC. The season odometer is capable of displaying 999,999 kilometers or 999,999 miles depending on units selected. Leading zeros are not displayed. The display will not roll-over to 000,000 if the maximum displayed miles or kilometers are reached. If the display limit is exceeded, the maximum value (999,999) is displayed. If the mileage is above 621,503 miles and metric units are selected the odometer shall display 999,999 km.


Circuit/System Testing
Ignition OFF, raise the vehicles drive wheels.
Engine ON, transmission in drive, verify the scan tool Vehicle Speed Sensor parameter matches the speedometer display.
? If the Vehicle Speed Sensor parameter does not match the speedometer display, replace the IPC.
Verify that the odometer is operating properly.
? If the odometer is not operating properly, replace the IPC.

Go into the driver info center and bring up the speedo settings, it is there.

On a digital display the default in U.S. is miles. Refer to your owner's manual or call dealer if you need to change it. A km is .6 of a mile, so just drive about 10 blocks (around a mile). If the odometer registers around 1 unit more it's probably miles, if it says close to 2 then it's probably km.

I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

To switch the speedometer and multi-function display between kilometers and miles, set the multi-function display to the odometer mode or a tripmeter mode, and then press the left set button for at least three seconds

hi,

Every 9,000 miles (14,500 km) the unit will show "SVC" on the display. This will continue until the service is performed and the service odometer is reset.
1. Determine mileage.
A. While in Dormant Mode enter Test Mode by pressing and holding the Heart Rate and Level keys simultaneously for five seconds.
B. Press the Dist key. DIST appears on the display. Record Mileage. NOTE: Once the unit exceeds 999 miles or kilometers the odometer will use both screens. Example:
12,805 miles or km would be displayed as 12 805 . NOTE: To exit Test Mode, press the Pause/Stop key .
Every 5,000 miles (8,000 km).
? Check running belt tension and tracking.
? Move treadmill and vacuum underneath..
? Lubricate elevation pivot points.
(Watch the videos for tentioning and lubricating treadmill belt.)

Use the steering wheel buttons, bottom left one till you get to "Settings" then UP arrow, then use the +/- on the right side till you get to "Instrument" or "Display" (depending on model) Use the arrows till you get to "Display units in miles / km" and use the + / - to change same. Escpae using the bottom left button.

You can just hold down the select button with the ignition on and that will also change it

If the odometer is a digital display, you may need to take it to the dealer to get the computer to report miles. This function may not be available to non-GM scanners. If it is a mechanical speedometer, you probably need to replace the entire head to get miles display. Check with wrecking yards for a used one. You can drive the odometer one way or the other by using a short length of cable in an electric drill.

there should be a menu button some where on the dash that will let you select it also it might have the gauge with both mph and km on it your owners manul should tell you how to change it

okay,for one,the odometer doesnt read in miles per hr,it reads miles driven, and two i have no idea if its possible to change the odometer to km traveled,if you're talking about the speedometer,its already there,get a european cluster :p