Question about 2004 Vento Gladiator XLS

1 Answer

No spark I have one of these motorcycles and have tried everything to get a spark from the ignition, I have replace coil, wire, plug, battery and jumped a new cdi box as well as a new alarm system. Still o spark and it is only reading 1 volt where the voltage goes into the the coil.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

CHECK SAFETY SWITCHES KICK STAND IS NOTORIOUS FOR THIS AND MAKE SURE YORE CONNECTIONS AND FUSES ARE GOOD NEUTRAL SWITCH ALSO CAN AND DOES GO BAD AND THE CLUTCH SWITCH

Posted on Jun 22, 2009

  • leejewel Apr 22, 2011

    Friend of mine said don't jump and try to bypass the cdi box. You may have fried it and burnt it out.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have no fire...checked all the basic options...


Hi, Leisha and the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have a nice day.
TROUBLE SHOOTING
How to diagnose no spark situation on motorcycle
How to test motorcycle CDI box ignition coil
Testing your motorcycle coil


Mar 03, 2016 | Motorcycles

1 Answer

Engine stopped running, has no spark.


Hi, Ron if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
Good luck and have a nice day.

Nov 20, 2015 | Motorcycles

1 Answer

I have yamaha warrior 350 that has no spark. have changed cdi box, pick up coil, ignition coil, stater, spark plugs basically everything besides wiring harness. has 110lbs compression. i need help.


Hi Cheyenne, if you have a CKP sensor it needs compression to send correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Battery voltage below 8.7 volts, loose or broken battery cables, check the "NEGATIVE" cable at both ends.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, MAP or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
Yamaha Motorcycle Service Repair Workshop Manuals

Oct 10, 2015 | Yamaha Motorcycles

1 Answer

Ignition coil wire diagram


Hi, Anonymous if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue, please visit the websites below. Good luck and have a nice day.
1986 K75 Has No Spark BMW com
Damn bike won start BMW K75 K100 K1 K1100
https://www.tradebit.com/filesharing.php/search/0/1986+bmw+k75c
BMW Motorcycle Parts Fiche OEM BMW Motorcycle Parts online 1970 present BMW
http://www.bmw-motorrad.com/us/en/index.html?content=http://www.bmw-motorrad.com/us/en/services/manuals/manuals_main.html¬rack=1

Sep 20, 2013 | BMW Motorcycles

1 Answer

Weak spark motorcycle


Hi Anonymous, and the usual suspects are:
1. Plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discarged.
6. Damaged wire or loose connections at battery terminals,
ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. If your bike has a CKP sensor you must leave both plugs in
head and check for spark with a 3rd plug. Good luck.

Jun 27, 2013 | Harley Davidson FLSTC Heritage Softail...

1 Answer

1998 gsxr 600 no spark


Instructions

Verifying the Spark
1

Remove the upper and side fairings, using a 4 mm Allen wrench to unscrew the fairing bolts. Unlock and remove the rider's seat, using the ignition key.
2

Pull the fuel lines off of the fuel valve under the left side of the fuel tank. Unscrew the pair of bolts from the base of the fuel tank, using a 10 mm socket. Pull the fuel tank to the rear of the motorcycle to remove it..

3

Pull the cables off of the two spark plugs on the right side of the motor. The spark plug cable furthest to the right is connected to the right ignition coil, while the second cable is connected to the left ignition coil. Unscrew the spark plugs from the motor, using a spark plug socket. Plug the ignition cables back onto the removed spark plugs.
4

Hold the spark plugs against the motor and start the motorcycle for a few seconds. Observe the gap between the electrode at the tip of both spark plugs for spark. Ideally, the spark should have a bright, blue appearance.
5

Replace the spark plugs with new DR8E spark plugs, if no spark is present. Repeat the test. Replace the corresponding ignition coil if there is still no spark present at the spark plugs' electrodes.
6

Proceed to Section 2 for further diagnosis, or reassemble the motorcycle following the reverse method of removal.
Testing the Windings
7

Remove the suspect ignition coil from the motorcycle's frame, using a 10 mm socket. Unplug the coil's cables from the remaining spark plug in the motor and from the spark plug removed in Section 1. Unplug the motorcycle's wiring harness connector from the back of the ignition coil. Remove the remaining ignition coil, if needed, using the same procedure.
8

Set your multimeter to read an R X 1 resistance range, using the meter's settings dial.
9

Measure the ignition coil's primary winding at the terminal that connects to the motorcycle's wiring harness, using your multimeter. Touch the meter's red probe to the coil's positive (+) terminal and the black probe to the coil's negative (-) terminal. Take note of the measurement on the meter's display. Replace the ignition coil if its primary winding has a resistance measurement less than 3 ohms or greater than 5 ohms.
10

Set your multimeter to read an R X 1,000 resistance range, using the meter's settings dial.
11

Measure the ignition coil's spark plug cables, using your multimeter. Touch the meter's probes to the metal connectors within the cable's end caps. Take note of the resistance measurement on the meter's display, indicated in ohms. Replace the ignition coil if the cables have a resistance measurement less than 25,000 ohms or greater than 45,000 ohms.
12

Reinstall the ignition coil if its primary winding and spark plug cables are within the specified resistance range, using the reverse method of removal. Replace the entire ignition coil if either the primary winding or the spark plug cables are within specification, as the ignition coil and its cables are a combined assembly.
13

Reassemble the motorcycle following the reverse method of removal. Connect the left ignition coil's cables to the pair of spark plugs in the middle of the motor's cylinder (#2 and #3), while the right coil's cable connect to the spark plugs on the sides of the cylinder (#1 and #4).

Jan 11, 2013 | 1998 Suzuki GSX-R 600

1 Answer

1979 Harley no fire to plugs after the ignition shorted out.


Hi Kelly, and the usual suspects are:
1. Plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discarged.
6. Damaged wire or loose connections at battery terminals especially the ground cable at "BOTH" ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. If your bike has a CKP sensor you must leave both plugs in
head and check for spark with a 3rd plug. Good luck and have nice day.

Dec 13, 2012 | Harley Davidson Motorcycles

1 Answer

93 sportster only fires on 1 side of coil


Hi Lowbrowbob, on twin cams make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Battery voltage below 8.7 volts, loose or broken battery cables especially ground cable to frame.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, MAP or BAS sensor.
7. Faulty ignition switch.
For a prime suspect please visit the website below:
Good luck
Harley Davidson Sportster error codes and how to access them

Oct 06, 2012 | 1993 Harley Davidson XLH Sportster 883...

2 Answers

TVS scooty pep plus not starting, changed with new new battery & new spark plug - no spark coming (I have tested the spark plug connected outside touching scooty metal body & start-kicking)


Possibly a bad ignition coil. Check the connections at the ignition coil,make sure they are clean and tight, If so,..then most likely either A: the ignition coil is bad,or B: the pickup on the stator rotor is bad or the rotor could be rusted on the raised portion where the pickup get its signal.

Aug 29, 2012 | 2010 TVS Scooty Pep

1 Answer

98 harley sportster 883 not firing...will not start....replaced literally everything. What am I missing?


Hi Anonymous, when checking for spark the CKP needs to measure the compression bump in order to send the correct signal to the ICM/ECM so always check for spark with either a third plug grounded or lift the end of the plug boot 1/2 " off one of spark plugs that are in the head. and the usual suspects are:
1. Fuel tank empty
2. Fuel supply valve turned off.
3. Fouled spark plugs.
4. Engine flooded with gasoline as a result of over use of enrichner.
5. Fuel valve or filter clogged.
6. Vacuum hose to automatic fuel supply valve disconnected, leaking, or pinched.
7. Discharged battery, loose or broken battery connections especially the negative cable at "BOTH" ends
8. Loose wire connection at coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, spark plug cable connections loose,
or cables connected to wrong cylinders.
10. Ignition timing incorrect due to faulty ignition coil, ignition module, or sensors " Manifold Absolute Pressure" "Camshaft Position Sensor" "Crank Position Sensor" "Brake Apply Sensor
11. Engine lubricant to heavy ( winter operation )
12. Sticking or damaged valves or push rod wrong length.
13. Primary cam sproket spline sheared or missing spacer.
14. Security alarm system not disarming.
For a primary suspect please visit the website below. Good luck and have nice day.Harley Davidson Wiring Diagrams and Schematics Harley Davidson Manuals Mark Workshop
Harley Davidson Sportster error codes and how to access them

Jun 17, 2012 | Harley Davidson Motorcycles

Not finding what you are looking for?
2004 Vento Gladiator XLS Logo

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vento Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

Brad Brown

Level 3 Expert

15682 Answers

Are you a Vento Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...