Question about 1996 kawasaki VN 1500 Vulcan Classic

1 Answer

30 amp fuse blows as soon as I drive 20 feet

Lose all power and the fuse burns out immediately

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You probably have a short in the circuit going to the engine computer...odds are you won't be able to correct it without tracing ALL wires in the system....sometime the dealer is the best bet.

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 f250 powerstroke..... Truck blew the 30 amp fuse that controls PCM coil relay,Fuel Heater,Waste gate Solenoid,Injector Driver Module,Relay Coil,after driving 20 mins.


Did you replace the fuse ? If yes, does it blow after driving ? Sounds like you may have a main power wiring problem, could be shorting to ground. Do you have any codes or an engine light on ?

Nov 25, 2016 | Ford F-250 Cars & Trucks

1 Answer

Replace 15 amp fuse to a 30


NO,NO,NO ! Fuses are electrical protection for the cars wiring installing a higher amp-age fuse takes longer to blow so your wiring gets hotter and starts to melt the insulation and shorts to other wires eventually burning up the harness. With a amp meter test the circuit to see how much power is needed to keep the circuit going if over rated (15 amp circuit taking 20 amps) then install a cycling circuit breaker 10 amp this will blow and cool and blow again continually then with a magnetic amp meter (Gauss meter) you can locate your short the source voltage causes the amp meter to jump as the fault occurs when you pass it meter will stop working.

Apr 22, 2014 | 2002 Ford Escape

1 Answer

I have a 1996 Chevy Astro van ECM 20 A fuse burns as soon as start to drive. Please help I am stuck on rest area and don't know if I can fix this problem myself. thank you


Find the biggest fuse in the panel probably a 30amp that goes to something that you don't need to use right away. Use it for the ecm fuse. If the 30 amp fuse blows, you need to disconnect the ecm and reconnect to see if that makes any difference. Sounds like a short, but it could be in the harness or inside the ecm. If the 30 amp fuse holds, get to the nearest parts store and buy a supply of 30 amp fuses. 40 amp if they have them. Maybe that will get you home without having to call a tow truck.

Jan 08, 2011 | 1998 Chevrolet Astro

1 Answer

So i hooked up the amp useing the pre-existing 8 gauge wire with a 30 amp fuse it worked for about and hour and started blowing the 30 amp line fuse. i replaced the line from 8 to 4 gauge and installed an...


this sound like a case of arcing power wire it happens very very easy if u use cheap wire especially from walmart. whatever u do keep using fuses and get a batt test asap. if u take out the fuses ull burn the amp like no other and plobably burn out the power rails which will be cheaper to buy a new amp after that

Oct 05, 2010 | Lanzar VIBE266 Car Audio Amplifier

1 Answer

Blowing 20 amp fuse


Hi that fuse should be a 25 amp and it runs the blower, heater, the day time running lamps, automatic light control and the rear defogger you would have to check each unit at a time what I would do is put a hire fuse and look for smoke on the wiring as soon as iI see whats burning I take the fuse off but you have to be quick and pull out the fuse before any thing burns if not check each unit mention and look for good luck.

Aug 17, 2009 | 1997 Pontiac Grand Am

2 Answers

How do i know what size fuse i need for a hitron hra 2500 amp?


im assuming you dont have the old one. typically it will be 20-50a. i recomend consulting the manufactures website.

Apr 25, 2009 | Hitron HRA-2500 250W 2CH Amplifier Car...

1 Answer

96 jeep cherokee, replace cps and the engine control fuse


The guy at the garage today, said he went out and put a fuse in it and it started right up. Thats all he did for now. I going to have a closer look on the weekend. But, as before when I went 1/2 mile it would burn the fuse again. We will have to see if it does again, I espect it will. Any idea?

Mar 26, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Car amp blows 12 volt wire fuse


the wire from your battery is blowing fuses? and you are using 20-30 A fuses? mine has a 100A fuse..look into getting new wire plus my wire is 4 gauge.., 1600 watts is too powerful for a 12 g wire and a 30 A fuse

Jul 26, 2008 | Car Audio & Video

Not finding what you are looking for?
1996 kawasaki VN 1500 Vulcan Classic Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...