Question about 2005 Harley Davidson FLHTCUI Electra Glide Ultra Classic

1 Answer

Speedomiter,horn,turning singnals, break light doesnt work. 2003 harley electra glide

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Harley Davidson Expert
  • 438 Answers

Check fuse cluster

Posted on Jan 07, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2336 Answers

SOURCE: replace rear brake pads

Remove right saddlebag, pull the two caliper mounting bolts and remove the caliper. Do not open bleeder or disconnect line. You will need to push a large screwdriver between the old pads before removing them in order to push the pucks back into the caliper or the new pads will not spread enough to reinstall. Then pull the two smaller bolts from the caliper and the pads will fall out. The pads are different for inside and outside, so pay attention, and remember, after reinstalling, before riding, be sure to pump brake pedal, and it may take a few stops before brakes stop as effectively as before.

Posted on Nov 10, 2008

  • 2336 Answers

SOURCE: fuse box

Looking at the bike from the front, it is located under the side cover, on the right hand side, you we need remove saddle bag. Once removed the fuse box is located under the plastic cover.

Posted on Nov 10, 2008

  • 2336 Answers

SOURCE: adjust clutch cable

If you have a stock cable you need a 9/16 and a 1/2 in. wrench. about 1/2 way downn the cable there is a rubber boot. pull the rubber boot over the adjustment. Loosen the liock nut and adjust the cable so you have aprox 1/8 to 1/16 in. slack in the handle. Re tighten the lock nut and pull the rubber back over the adjustment.

Posted on Nov 10, 2008

  • 10865 Answers

SOURCE: changing oil on 2003 electra glide

I don't blame you for wanting to do this yourself. Be sure to use a harley filter and harley oil.

Drain the oil, replace o ring on drain plug, replace drain plug, remove oil filter, fill oil filter with 20/50 harley davidson oil and replace filter being careful not to overtighten, fill oil tank with the bike upright to the fill line on the dipstick. Take the bike for a short ride and check the fluid level while warm.

Posted on May 20, 2009

  • 69 Answers

SOURCE: How do I change the front and rear brakes on a

Not too hard - Undo the two bolts on the caliper and then seperate the caliper and pull the old ones out. Insert the new ones and put the bolts back in to hold the caliper back together and then install them back on the bike with the two retaining bolts. Use a bit of lock tight (Blue) on the threads. Warning do not let anyone apply pressure on the brakes while you have them off the bike or you will have a mess and/or a problem.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Harley troubleshooting


You most likely have a hot wire grounding out

Jul 04, 2014 | 2008 Harley Davidson FLHT Electra Glide...

1 Answer

2008 electra glide speedometer, turnsignal and brakelights not working


Hi Elizabeth, always check fuses and bulbs first for broken filaments. Then check the connection at the rear fender wiring harness, inspect for corroded, broken or loose pins. Use a dab of dielectric grease and repair as necessary. Check your brake relay if you have one , check your brake light switches for continuity, some models rear turn signals were single filament bulbs only, no running light. If all else fails get out your test light and start tracking the power wire from the harness connection. For a free wiring diagram please visit the website below and good luck:
Harley Davidson Wiring Diagrams and Schematics

Oct 10, 2012 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Fuse box location for 1986 harley davidson electra glide


Hi Anonymous, 1986 FLHT had no fuses only circuit breakers located under the sppedometer. Good luck and have nice day.

Jun 04, 2012 | 2003 Harley Davidson FLHT Electra Glide...

1 Answer

How to Change a Harley Electra Glide horn


Well there is a nut that holds on to a rubber mount usely chrome undo it there will be 2 wires 1 ground 1 power un plug note placement install new horn in reverse..good luck ..ps some older bikes do not have a direct ground but a strap that goes from 1 side of rubber mount to the other,,,

Oct 16, 2011 | 2003 Harley Davidson FLHT Electra Glide...

1 Answer

Blinkers and horn do not work


Check the fuses as I think the horn and turn signals are on the same fuse. The fuses are located either under the seat or the left side cover.

Good Luck
Steve

Mar 24, 2011 | 2003 Harley Davidson FLHTC Electra Glide...

1 Answer

Brake lights,turn signal and horn not working...


Check the wiring within the headlight shell--look for connectors that may be corroded or pulled loose. A little WD-40 will favor connection integrity when sprayed into the connectors, then coupling and uncoupling them several times. Hope this helps!

May 24, 2010 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Horn wont work 1996 flhtcui electra glide classic


Its possible that just a wire came loose...but if thats not the case take off one of the wires and read for voltage while pushing the horn button..if you get voltage its a bad horn..if not you'll need to check the horn button it may be bad.
hope this helps...when my horn went bad i had voltage..i replaced the horn and it worked fine...also just insure that the wires are on solid and arent corroded or damage before you try all this other stuff first. Hope this helps .

Apr 05, 2010 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

My bike quit while riding home the other day.


start of breaking down of HT coil, if breaksdown while warm, leave for a while and start back up, it's HT coil, sounds like you should just carry on and see if it gets worse, then you'll know. unusual for a sudden complete breakdown so you shouldn't be stranded.

Aug 09, 2009 | 2003 Harley Davidson FLHTC Electra Glide...

Not finding what you are looking for?
2005 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...