Question about 2001 Harley Davidson FXDXT Dyna Super Glide T-sport

1 Answer

Pck5315rx hv module

BRAKE LIGHTS, TURN SIGNALS, SPEEDO NOT WORKING

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

I have no idea what the numbers you refer to are about. You need to see what codes are set

Posted on Nov 26, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wasiv101
  • 11 Answers

SOURCE: no power to horn, tach, speedo, left turn or right

Check wires by neck and under tank,some folks have had problems with wires breaking. ignition switch is another area to check

Posted on Feb 21, 2010

co7196
  • 3433 Answers

SOURCE: 2004 FLHTCUI ULTRA CLASSIC..TRYING TO WIRE UP FOR

chk backwards to your turn signal control unit. The brake lights and rurn signals are routed in a way that would affect each other.Is this a four wire or?Chk fuses 1st. Good Luck- -Ned- A good grd is important.

Posted on Jun 01, 2010

wd4ity
  • 4565 Answers

SOURCE: '05 1200 custom: left rear turn signal/brake light

Your bike is not equipped with the old style "flasher" like they used to be back in the '80's. You bike has what Harley calls a Turn Signal Microprocessor. It's a "black box" about a half inch thick by an inch and half wide by three inches long. It has a large plug with about a dozen wires on one end and a mounting bolt in the center of it. Exactly where it is, I have no idea as Harley moved these things around as much as they did the oil drain on the Sportsters. Underneath the battery is a bad place for anything, especially electrical components. The faint clicking sound you're hearing may be a circuit breaker. By the signals flashing very rapidly, this would indicate a high current flow that may be caused by a short circuit.

Good Luck
Steve

Posted on Aug 05, 2011

  • 1 Answer

SOURCE: Speedo, turn signals, brake lights, horn stopped working. All else is fine.

Did you find any solution I'm having the same problem with my 2001 road king I know that the fuse is blowing just wondering if you found where to start looking

Posted on Mar 20, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No turn signals no brake lights no horn no speedo on a 2000 dyna fxdl


Hi Anonmous, get out your test light and start at the ignition switch and work your way to switch housings and beyound. If you disconnected the battery for any reason you might have a TSM/TSSM issue. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics
Good luck

Feb 04, 2014 | Harley Davidson FXDL Dyna Low Rider...

1 Answer

Brake lights don't work on my 2010 FXDWG and my right turn signal doesn't work either. There is a key icon on my speedo that is on in red.


Hi Ed, always check fuses and bulbs first for broken filaments. Then check the connection at the rear fender wiring harness, inspect for corroded, broken or loose pins. Use a dab of dielectric grease and repair as necessary. Check your brake relay if you have one , check your brake light switches for continuity, some models rear turn signals were single filament bulbs only, no running light. If all else fails get out your test light and start tracking the power wire from the harness connection. You could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below. You may also need an alarm reset. Harley Davidson Wiring Diagrams and Schematics
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Oct 07, 2011 | Harley Davidson FXDWG - FXDWGI Dyna Wide...

4 Answers

I have the same problem with my 2000 v70 glt a not only does the break, abs, and check engine lights come on and the speedometer and odometer don't work but the arrow starts flashing and the vehicle seems...


The most common problem is with the ABS control unit. You will most likely have to replace it. It is located under the brake hydraulic unit (not the master cylinder). This part can be purchaced from a Volvo dealer, or sent to one of the many places that repair them. If you choose to fix it yourself, and would like the name of one of the companys that repair them, let me know.

Nov 23, 2010 | 1999 Volvo V70

1 Answer

I have a Chevy 2500 4X4 with brake lights not working. I have all other lights working. I only have one brake light working when I turn on the right turn signal then my left brake light will work. What's...


What year?

Sounds like a turn signal switch. Earlier models would use the same bulb for the brake and turn signal. The turn signal switch will interrupt power to the brake light and route the signal to either the left or right bulb depending on with way you where turning. Usually you can wiggle the turn signal switch and get the brake light to work momentarily when this is the problem.

Newer vehicles use a lighting module that looks for inputs from the turn signal switch and brake pedal switch and then decides where to send power. This module is also know to go bad.

Oct 11, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

2003 Suzuki VL 800 speedo cluster, signals, brake light won't work. Worked on the way to work this A.M. Checked the two fuses under seat. ?


Did you also check the system fuses? The fuse box is located behind the left side crankcase cover above the coolant reservior.

The 15 amp Signal fuse protects the coolant temperature light, the turn signal indicator light, the neutral indicator light, the oil pressure light, horn, brake/taillight, postition light and turn signal light. Basically, if this fuse is blown, your cluster will be inop.

Please let me know if this is helpful.

Jul 21, 2010 | 2002 Suzuki VL 800 Volusia

1 Answer

My speedo does not work and my blinkers dont turn off


If your speedo isn't working the turn signal module is not getting a mileage signal and thinks that you are stopped. Also, the modules were troublesome and were modified several times.

Mar 17, 2010 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Speedometer


check for a connector not fully seated.

here's info

Vehicle Speed Sensor (VSS)
On vehicles equipped with 4-wheel anti-lock brake systems (4WABS), the vehicle speed signal is generated by the rear anti-lock brake sensor and sent to the 4WABS module. The 4WABS module sends the vehicle speed signal via circuit 679 (GY/BK) to all systems that require a vehicle speed signal input. Vehicles equipped with rear anti-lock brakes (RABS) generate a vehicle speed signal from the rear axle speed sensor. The generic electronic module (GEM) receives this signal (VSS_GEM) for internal use and then distributes it to the appropriate other users (i.e., the powertrain control module [PCM], speed control module, and speedometer).
Speedometer
The electronic speedometer (17255) receives a speed signal from the 4WABS module (if equipped with 4WABS) or the generic electronic module (GEM)/central timer module (CTM) (if equipped with RABS). RABS = Rear antilock brake system

Jan 17, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

No turn signals or side brake lights on 94 chevy suburban


the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Oct 18, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
2001 Harley Davidson FXDXT Dyna Super Glide T-sport Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...