Question about 2001 Harley Davidson FLHTCUI Electra Glide Ultra Classic

1 Answer

Get brake calupers back on after removing front wheel

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 39,960 Answers

Hi Anonymous, if you are having trouble try inserting a large screw driver or chisel in between the pads and force back the caliper pistons enough so that the calipers will slide over the rotors easily. Ater you bolt them back on torque bolts to 20 ft lbs. Then pump brake lever until you get a nice strong feel and your good to go. Good luck

Posted on Apr 16, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel doesn't spin freely and squeaks on 2n'd day i got it.


Hi James:
If New, I'd take it back to the dealer.
If used.....
Set bike on jack so front wheel is raised. Make sure it is secure so can't fall.
1) Remove front brake pads........... spin wheel If it still squeaks, remove wheel and service bearings.
If no squeak when brakes removed, service brakes.

Jan 18, 2016 | Motorcycles

1 Answer

2001 changed all brakes and brake lines and rear calupers but rear is still sticking brakes will not release whats wrong


Hi Annabel.
Sorry you are having brake trouble. It is not an uncommon problem, and the usual first action is either to get a pal to get at the other end of the car and both shove it a foot or two each way to loosen the calipers, or start the engine and do the same. Just gently go forward and back several times till you can sense the handbrake loosens and gives you the feel back. Try working the handbrake a few times. If you feel at ease with that, drive round the block till you feel confident. On the jack in neutral, engine off, you can test if the wheel rotates freely. The only alternative would be to put it on the jack, take off the wheel and get dirty with the tools. You can't drive to Kwikfit with seized brakes, sadly. Are you attractive, with a helpful boyfriend? No problem! Good luck.

Alex

Jun 09, 2014 | Cars & Trucks

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

I have an 04 Malibu and my front brake on the left side locks up on the wheel when I drive. Sometimes its really bad and if I continue to accelerate, the car limps and shakes so I most of the time have to...


sounds like your caluper is locked up.ull the tire take out brake pads have someone pump the brakes to see if pistion is moving if not try to find a rebuild kit if not a new one is in order

Apr 16, 2013 | 2004 Chevrolet Malibu

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

2 Answers

2000 olds bravada rear brakes are draging. changed brake hose's to calupers and the center hose as well. with new brake and rotors still draging not sure what to do next.


I also have this problem on my 2000 Bravada - replaced all rotors and back calipers, brand new brake pads, new system and my rear caliper STILL chewed up a brand new brake pad in one week down to the metal. Checking for an emergency brake issue at this point - if anyone has any suggestions about how to unhook the E Brake, please share!

Jan 13, 2010 | 2000 Oldsmobile Bravada

1 Answer

I have a bad wheel bearing how do I replace it


Hub and Bearing Assembly
ani_caut.gif CAUTION: Do not begin this removal procedure unless the following parts are available:
  • A new front axle wheel hub retainer (3B477) (Step 1).
  • A new inboard halfshaft joint stub shaft circlip.
Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.

Removal
  1. Turn ignition switch to the OFF position and place the steering column in the unlock position.
  1. ani_caut.gif CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
    Remove and discard front axle wheel hub retainer (3B477).
  1. Raise vehicle on hoist.
  1. NOTE: Make sure steering column is in the unlocked position, and do not use a hammer to separate tie rod end (3A130) from the front wheel knuckle (3K185) . Use extreme care not to damage boot seal.

    Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
  1. Using Tie Rod End Remover 211-001 (TOOL-3290-D) or equivalent and Tie Rod End Remover Adapter 211-087 (T81P-3504-W), remove tie rod end from front wheel knuckle.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to remove the nut, or bearing and seal damage will result. Loosen the nut first, then remove nut from stud using the hex hold feature.
    For SHO vehicles, remove vinyl cover from upper link stud.
    Remove stabilizer bar link (5K484) from front shock absorber (18124) .
  1. Remove disc brake caliper (2B120) and support with wire to obtain working space. Do not allow disc brake caliper to separate from the front disc brake caliper anchor plate (2B292) to prevent contamination of the disc brake guide pin journals. Do not allow disc brake caliper to hang from front brake hose (2078) . Remove front disc brake rotor (1125) . Remove front disc brake rotor from wheel hub (1104) by pulling it off the lug bolt (1107). If front disc brake rotor is difficult to remove from front wheel knuckle , strike front disc brake rotor sharply between lug bolt with a rubber or plastic hammer.
    If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
  1. Remove anti-lock brake sensor mounting bolt and front brake anti-lock sensor (2C204) .
  1. Remove and discard lower ball joint nut. Using Remover Adapter 211-211 (T96P-3010-A1), separate lower ball joint from front suspension lower arm (3078) .
  1. Using Rotunda Spring Compressor 014-00781 or equivalent, compress front coil spring (5310) until lower ball joint clears front suspension lower arm .
  1. Using Front Hub Remover/Replacer 204-069 (T81P-1104-C), Two Stud Adapter 205-237 (T86P-1104-A1), Metric Hub Remover Adapter 204-085 (T83P-1104-BH) and Front Hub Installer 204-067 (T81P-1104-A), press front wheel driveshaft joint (3B414) from wheel hub . Wire front wheel driveshaft joint to body to maintain a level position.


    df1570a.gif


    Item Part Number Description 1 204-085 (T83P-1104-BH) Metric Hub Remover Adapter 2 204-067 (T81P-1104-A) Front Hub Replacer 3 — Turn Wrench Counterclockwise 4 — Hold Wrench Stationary While Turning Other Wrench 5 204-069 (T81P-1104-C) Front Hub Remover/Replacer 6 204-067 (T81P-1104-A)1 Two Stud Adapter A — Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)
  1. Remove and discard three hub and bearing retainer bolts from front wheel knuckle .
  1. NOTE: Wheel hub is not pressed into front wheel knuckle . Do not use slide hammer to remove a stuck wheel hub . Do not strike back of inner bearing race. Use of these methods will damage bearing internal parts.

    NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inboard and outboard wheel hub/knuckle mating surface and allow to soak.

    Remove wheel hub from front wheel knuckle .


    f8656a.gif

Installation
  1. NOTE: If wheel hub is damaged or if any end play is detectable, replace wheel hub . End play is not adjustable. If wheel hub is disassembled, the assembly must be replaced.

    Remove all foreign material from knuckle bearing bore for correct seating of new wheel hub.
  1. Lightly lubricate mating surfaces of bearing corner and front wheel knuckle.
  1. ani_caut.gif CAUTION: Knuckle bore must be clean enough to allow wheel hub to be completely seated by hand. Do not press or draw wheel hub into place.
    Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
  1. Push front wheel driveshaft joint into wheel hub . Hand start front wheel hub retainer.
  1. Slowly release Rotunda Spring Compressor 014-00781 or equivalent while guiding lower ball joint into front suspension lower arm .
  1. Install new lower ball joint nut. Tighten to 68-92 Nm (50-67 lb-ft).
  1. Install tie rod end into front wheel knuckle . Install new slotted nut and tighten to 47-63 Nm (35-46 lb-ft). If necessary advance nut to install a new cotter pin.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.
  1. NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.

    Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: The front axle wheel hub retainer must be tightened to specification immediately during installation. If the retainer is not tightened immediately, the nylon lock will set incorrectly, leading to incorrect torque readings and bearing failure. Any front wheel hub retainer that is not immediately tightened to specification or is loosened must be removed and a new retainer installed.
    Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
  1. Install wheel and tire. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.

May 28, 2009 | 1999 Ford Taurus

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

Replacing hijet front wheel bearing


after removing the wheel remove the brake caliper and rotor. after removing the brake assembly look on back of wheel hub assembly look for three bolts. remove bolts and remove wheel hub bearing.

Mar 19, 2009 | 1992 Daihatsu Charade

1 Answer

94 landcruiser brakes


Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.


  1. Raise and support rear of vehicle, then remove wheel and tire assembly.
  2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
  3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
    1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
    2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
    3. On 2WD T100 models, proceed as follows:
      1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
      2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
    1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
    2. Remove adjusting lever spring, then the adjuster from front shoe.
    Inspection
    1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      1. On 2WD T100 models, proceed as follows:
        1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
        2. Assemble and install wheel cylinder.
        3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
        1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
            1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
            2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
            3. Install tension spring.
          1. Ensure proper parking brake travel.
          2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
          3. Adjust strut to shortest possible length, then install drum.
          4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS
  1. Remove caliper.
  2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
  3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
  4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
  5. Remove free wheel hub body and gasket.
  6. Remove locknut, lock washer and adjusting nut.
  7. Remove axle hub and brake disc as an assembly.
  8. Remove oil seal and inner bearing from hub.
  9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.
  1. Raise and support front of vehicle, then remove tire and wheel assembly.
  2. Remove clip and hole pins, Fig. 9.
  3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
  4. Lubricate caliper housing with suitable brake grease at pad contact points.
  5. Reverse procedure to install.

Jan 28, 2009 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
2001 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...