Question about 2009 Harley Davidson FXCWC Rocker C

1 Answer

Turn signals blink right left right left bike wont start

Cant get engine to turn over but turn signas keep flashing right left right left for a few seconds after sturning switch off

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

Sounds like the security system is active.

Posted on Nov 26, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 01 Softail Deuce left turn signal comes on, will not go off

I'm new to this site but actually has fielded a question about a Triumph motorcycle I'm worrking on!

I have an '03 Anniversary Deuce and I ran into (not the exact) but similar problem. My bike has the bars internally wired from the grips all the way through the top triple tree. Somehow over time the turn signal wire got shorted "internally". You might want to just unbolt the turn signal switch from the bars to see if the wire got pinched up high. If not...move the wires around to see if that helps. If it does...ultimately you should re-wire the connections. Just my experience...good luck!

Posted on Feb 10, 2009

  • 300 Answers

SOURCE: indicator problem

The flasher unit is called the TSSM module. It is a combined flasher and alarm unit. A new one will require your alarm keyfobs to be matched to it. An expensive unit if faulty. If you replaced the earth wires and now its blowing fuses, then I would check your work. The fault has changed after you worked on the vehicle so logic dictates you have caused this. The black wire is usually the earth on these indicators but it is a possibility that these are routed through the TSSM module. You might have done damage if this is so.

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: 2007 sporster turn signals flasher , bike wont start

He's right! The key fob for the security system needs a clear signal to the module to disarm the bike. That's why the flashers turn on. If the fob is at the bike, the security module has lost it's memory, or the antenna for the key fob reception is not connected. You also need to squeeze the clutch lever to allow the engine to engage also...new safety feature i think for 07. Hope this helps.
david

Posted on Aug 08, 2009

  • 8 Answers

SOURCE: 2007 harley softail turn signals left side stoped

More than likely a broken wire you will have to trace

Posted on Sep 20, 2009

  • 109 Answers

SOURCE: left turn signal not working proper

Turn signals flashing is the confirmation of alarm system being on.I thought both sides flashed but if alarm is faulty guess that's messed up too. Try starting from stratch with alarm,disarm it[disconnect neg wire at battery]then reconnect wire and when that sets off alarm turn it off in normal way.That should get things back on track.Plus,try replacing the flasher unit,don't know why this works but I've heard of it.

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Security key on and bike wont start


First, open fob and make sure battery is making good contact and no corrosion on contacts.

Also, you might need a new fob battery.

Finally, if you know the security code, you can disable the security system.

DO NOT sit on seat, lift bike off kick stand, or anything else that will activate the security mode!

Turn IGN to IGNITION.

Quickly (within 2 seconds) hold BOTH turn signal switches until confirmation signal (KEY icon flashes at fast rate, in odometer window, a flashing "-" will be followed by 4 more dashes = "----")

Enter 1st digit (a) in PIN by pressing LEFT turn signal switch (a) times (i.e., 5 times for the number 5)
The 1st "-" will become the 1st digit (i.e., "5")

Press RIGHT switch signal 1 TIME.
The 1st digit is stored and the dash will flash.

Enter 2nd digit (b), and repeat sequence until done.

After the 5th digit is entered, the KEY icon stops blinking, and the system is disarmed.

The system will stay off until the IGN switch is turned off.

If at any time during disarming sequence an error is made, wait 2 minutes before trying again.

Mar 16, 2013 | 2008 Harley Davidson FLHX Street Glide

1 Answer

My immobiliser wont let me start the bike


This may help you ... http://www.youtube.com/watch?v=RTy_JKI9cQ0 ... probably not.

Resetting your security system depends on which system you have. To do any of them, you must have the fob. If you don't have the fob, only Harley can clear. Be prepared to prove ownership when you arrive.

To reset the code with a TSSM equipped bike, you will:
1) Set your kill switch to off
2) Quickly turn the ignition switch on, off, on, off, on
3) Immediately press and let go of the left turn signal switch twice (press, let go, press, let go)
4) Press and let go of your fob button twice (press fairly hard, it's designed to resist being pressed by keys and what not in your pocket)
5) Current PIN number will be displayed on odometer
6) Change the PIN by pressing the left signal until the desired number is reached
7) Press the fob button twice to cycle to the next number and repeat step 7
8) Press and let go the right signal and turn ignition off when 5 digit PIN is satisfactory
NOTE: Steps 2 through 4 must be completed in quick succession of each other.

Now you can have the bike armed, and disarm with the PIN (example PIN will be 25522 in the following steps):
1) Ignition switch to Accessories
2) Immediately press both turn signals at the same time (red key light on you speedometer will flash rapidly if done right)
3) Press and let go the left signal 2 times
4) Press and let go the right signal once
5) Press and let go the left signal 5 times
6) Press and let go the right signal once
7) Repeat for each of the last three numbers of the PIN (left 5 times, right once, left 2 times, right once, left 2 times, right once)
8) Red key on speedo will stop blinking if done right (security has been disarmed)
NOTE: Steps 2 through 7 must be completed in quick succession of each other.



To reset the code with a HFSM equipped bike, you will:
1) Have your key fob near the bike
2) Set your kill switch to off
3) Quickly turn the ignition switch on, off, on, off, on
4) Immediately press and let go of the left turn signal switch twice (press, let go, press, let go)
5) Press and let go the right signal once
6) Current PIN number will be displayed on odometer
7) Change the PIN by pressing the left signal until the desired number is reached
8) Press the right signal to cycle to the next number and repeat step 7
9) Turn ignition off when 5 digit PIN is satisfactory
NOTE: Steps 3 through 5 must be completed in quick succession of each other.

Now you can have the bike armed, and disarm with the PIN (example PIN will be 25522 in the following steps):
1) Ignition switch to on
2) Immediately press both turn signals at the same time (red key light on you speedometer will flash rapidly if done right)
3) Press and let go the left signal 2 times
4) Press and let go the right signal once
5) Press and let go the left signal 5 times
6) Press and let go the right signal once
7) Repeat for each of the last three numbers of the PIN (left 5 times, right once, left 2 times, right once, left 2 times, right once)
8) Red key on speedo will stop blinking if done right (security has been disarmed)
NOTE: Steps 2 through 7 must be completed in quick succession of each other

Feb 24, 2013 | 2010 Harley Davidson FXDF Fat Bob

2 Answers

Lost my FOB I have a new one but I cant turn the alarm off, I called harley and they said to turn on the bike and immediatly push both left and right blinker buttons, Ive done this probably 30 times and it...


OK so here is your solution. from your dealer when you purchased your bike with the alarm system you were given a 5 digit pin number. in order to turn it off manually you need to unlock (if locked) the switch, turn it to accessory.
push both left and right blinker buttons in
with the left blinker button is you "digits" so if (ex 56726) push the left button five times
to go to the next button push the right blinker one time then left six times
the right blinker one time and left blinker seven times
then right two times right once
left six times and right once. this will turn off the alarm

to program the fob you need to turn the ignition switch in a sequence of
on off on off on
with the blinker buttons you push
left left right left and your signals will flash the hazards twice
push and hold the fob button till the hazards blink three times and you have just programed your fob
push and hold your fob to set alarm and double click to disarm your alarm

Dec 12, 2010 | 2005 Harley Davidson FLSTN- FLSTNI Softail...

2 Answers

Left turn signal comes on when I turn the ignition then doesn't work


I am having the same issue on a 2005 FLHRCI Road King Classic. Basically the left turn signal comes on when I start the engine. It will not cancel by pushing the left turn signal button. However, if I push the right turn signal button the left will go off and the right will start blinking. Sometimes, this same action starts all four signals blinking (like the emergency flashers). It is very erratic. I have Kuryakan pancea rear taillights and brake light. The brake light went out so I went a bought a new brake/taillight with a new adapter. Brake lights work now but the blinker problems happens whether the back lights are connected or not. Front turn signals are stock.

Any help would be greatly appreciated.

Jul 11, 2010 | 2004 Harley Davidson FLHRS - FLHRSI Road...

2 Answers

2007 sporster turn signals flasher , bike wont start


Does it have a key Fob? If it does it has security on it and you have to have the key fob with the bike to start it. Otherwise the flashers will blink

Jun 13, 2009 | 2007 Harley Davidson XL 883 Sportster

1 Answer

Left turn signal not working proper


Turn signals flashing is the confirmation of alarm system being on.I thought both sides flashed but if alarm is faulty guess that's messed up too. Try starting from stratch with alarm,disarm it[disconnect neg wire at battery]then reconnect wire and when that sets off alarm turn it off in normal way.That should get things back on track.Plus,try replacing the flasher unit,don't know why this works but I've heard of it.

Apr 06, 2009 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

2005 Silverado - Hazard lamps come on when I use right turn signa


It is your flasher module. It is on the backside of the fuse box under the dash. You need to remove the panel below the steering wheel, above the peddles. The replacement part number is 10383321. Once you have the panel off it just pulls out and replace it with the new one. I got one on ebay for about
$30 shipped.

Mar 23, 2009 | 2005 Chevrolet Silverado

1 Answer

Turn signals, Hazard lights


I would replace the bar switch assembly.

May 18, 2017 | 1998 Jeep Wrangler

Not finding what you are looking for?
2009 Harley Davidson FXCWC Rocker C Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...