Question about 2008 Cagiva Raptor 650

1 Answer

Technika spare parts australia

Can you supply or advise who can a chain guide that goes around the swing arm to stop the chain rubbing Maybe Part No CA 0006975 Regards Geoff

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cagiva Master
  • 40,008 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do i have a slight rubbing/ticking noise from very low speed coasting on my bike?


lots of reasons .......could be chain rubbing on chain guide if it has a chain,or may be worn out chain,.........could be tire rubbing ....check and make sure both tires are evenly spaced between forks and swing arm.....if it has a chain guard make sure chain is not rubbing on guard....Best way to check is to put it on it's double kick stand and start the bike put it in gear and let the tire spin at idle and listen and look for the problem.

Jul 16, 2014 | 2007 Suzuki Bandit 1250

1 Answer

I have a 91 22re 4wd 5spd when it first starts it makes a loud clacking noise that goes away after a few seconds what is that noise my rocker arm shafts and rocker arms are in good condidion


Sounds like it could be your timing chain. There is an automatic chain tensioner and over time when the chain gets a lot of miles on it the plastic guides and chain have to be replaced. Typically around 125,000 miles or more. You can remove the valve cover and look down the front of the engine to verify this. Look to see if the plastic guides are still in place and that the chain is not rubbing a hole in the front timing chain cover. Let us know your findings.

Dec 31, 2013 | 1991 Toyota Pickup

1 Answer

My rear wheel is rubbing on the swing arm? Can I just bring the wheel in for repair or is it best to bring the bike in?


you will need to take the bike in. to know the cause, and what the solution is to fix it.

Oct 31, 2012 | Honda Motorcycles

1 Answer

My Hp colorlaserjet 37ooDN is showing the error : 59.C0 Pl. HELP


Hi,
59.C0 Error Displayed on Control Panel Remove all the print cartridges from the printer so the right swing guide will be visible and check for the parts described in the photos below.
If the right side swing guide does not go all the way back, the 59.C0 alienation error will be displayed on the control panel. A plastic part on the swing guide could be missing.
See photo below where the three circles are on the right side of the printer.
Figure 1: Right swing arm assembly
37001See photo for details of the part. Call-out 1 in the photo below shows the parts in place, while Call-out 2 shows the missing part. (The part looks like an upside-down t.)
Figure 2: Missing part causing 59.C0 error
370021 - Part in place
2 - Part missing
Another cause for a 59.C0 error can be the black sliding lock is broken, out of place, or missing the spring. (See figure below) This can cause 59.C0 errors or 10.92.XX errors.
Figure 3: Right swing frame assembly
37003Replace the swing guide. Please look for the missing part in the printer so it will not cause other issues from movement to other parts of the printer.
If the part in the call-out is present, close the door slowly and observe the right side swing arm. It should close uniformally with the left side swing arm. If not, arrange for service on the printer and replace the right swing arm.

Jun 20, 2011 | HP LaserJet 3700dn Printer

1 Answer

Hi my chain was to loose and tensioners were maxed out . so i took out a link worked fine brought it up to the 3rd mark on the rear arm sweet. but now my tire is rubbing on swing arm ?? tires the rite...


LOL! U took too many link.... u just have to deduct at least 1 link at a time or the tire is misaligned, i meant the way u put back the tyre in the swing arm!

Jun 12, 2011 | 1990 kawasaki ZXR 250

1 Answer

Chain keeps getting lose so i tighten it it get lose now it make a noise what is the problem


Get your rear wheel off the ground. Spin the wheel observing if the chain rides up and down the teeth of the sprocket. When this is happening notice if the chain is getting tight than slack, then you know you have a stretched chain (maybe only a 1 foot section). Replace the chain. If the sprockets are worn you may be able to save money by purchasing a chain and sprocket kit. If it is a seventies vintage Honda, they had a fiber bushing for a swing arm bearing. They were noted for failure causing the chain to bounce off he frame and swing arm . A loud banging sound while you ride.

Sep 25, 2010 | Honda VF 750 S Motorcycles

1 Answer

Okay. Thanks to Guru, the handlebars were easy to fix. Maybe shouldn't try to ride this thing daily on the road, because now the chain came off. I put it back on, but need to see if there is an easy way...


hi, it sounds to me like the bike has been ridden hard and needs the chain replacing due to it strecthing. on the swing arm at the back is their two bolts sticking out the end of each swing arm their should be one in one side of the swing arm and one in the other side of the swing arm, this is right at the very back of the swing arm.
if you find these then these are the adjusters for the back wheel you then need to loosen the back wheel bolt but dont take it out then adjust these adjusters by the same amount do it in half a turn a time you need to do both the same else the back wheel wont be level keep tightening them in and this will then pull the wheel back and this will tighten the chain if its all ready adjusted fully then the chain is scrap and needs replacing, if you dont have adjusters then the chain needs replacing, it will keep coming off if its slack

you can cause damage to the bike if the chain comes off whilst riding at speed so it may be best to get the chain before you use the bike



Aug 15, 2010 | 2004 Suzuki DR 200 SE

1 Answer

How to u put chain on r6


If the chain has a master link, then you can just loosen the rear axle and let the chain tension adjustment all the way in. Then wrap the chain around both sprockets and install the connecting link. After this retighten the chain. For a chain without a master link( endless chain) you will have to remove the swing arm to allow you to get the chain on the front sprocket. After reinstalling the swing arm, and rear wheel you can adjust the chain tension and then tighten the rear axle.

Apr 09, 2010 | 2000 Yamaha YZF-R6

1 Answer

Chain touching the swing arm


Hi ..... Welcome to the 'custom' world ! As you've discovered changing one thing leads to another. The chain angle has changed due to the shock length. You could try going to a breakers and buy another chain guide rubber ? More involved solutions could be to off set gear box sprocket, intermediate chain tensioner pully, go back to stansard shocks (which is main problem) and widen rear mudhuard/fender (which as you can weld isn't a big issue) or make up a 'tunnel' out of a round or square section of nylon and allow the chain to run through it. Let us know how you get on.

Dec 24, 2008 | 2005 TVS Fiero F2

1 Answer

Drive chain adjustment


To adjust the chain you need to make sure you make the adjustment with the swing arm parallel to the ground, (this is the tightest point in the arc of the swing arm moving rotation), at that point you want to be able to put two finger between the chain and the swing arm at the swing arm pivot bolt. This will insure proper adjustment every time. The best thing to do is have somebody sti on the bike off the stand to make sure the swing arm is at its MAXIMUM arc, otherwise you stand a significant chance of over tightening it and this can and WILL cause SERIOUS damage to your engine. You will rip the output shaft bearings out of the center cases.
You also want too make sure you have proper wheel alignment as well. There are marks on the rear of the swing arm for adjusting the chain, make sure you have the marks on the adjusters in the same location on BOTH sides of the swing arm.
Please let me know if you need further assistance.
Regards,
RSelvy

Dec 17, 2008 | 2005 Suzuki RM-Z 250

Not finding what you are looking for?
2008 Cagiva Raptor 650 Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cagiva Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Steve P
Steve P

Level 3 Expert

2546 Answers

Are you a Cagiva Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...