Question about 2008 Suzuki Boulevard M109R

Open Question

What type of oil goes in drive shaft 09 109r - 2008 Suzuki Boulevard M109R

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dose it mater what position the oil pump drive gear is when inserted as long as you can line it on a plug wire for # 1


You don't say what make, model, and year your car is. If the distributor has the gear on its shaft, then it doesn't matter because the oil pump doesn't have the drive gear on it. It has a hexagonal shaped shaft the goes into the bottom of the distributor as you insert it into the engine. If the distributor is driven off the camshaft, then it only goes on one way and has no interaction with the oil pump.

Nov 03, 2016 | Cars & Trucks

1 Answer

I have a honda HRA214 motor i took out of a push


you cant convert a vertical shaft motor to a horizontal

Sep 13, 2014 | Cars & Trucks

1 Answer

How to drain oil from middle drive shaft


Hi, Garywalia for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
What type of oil for your shaft drive Yamaha Star Forum
How To Change The Final Drive Oil On star 650
98 00 Yamaha XV650 Star Service Manual XVS650 Moto Data Project
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Feb 26, 2014 | 2007 Yamaha V Star Classic

2 Answers

Vortec oil pump on a gmc jimmy


Don't start the car !!!

Can you see the part from the whole where the distributor goes ?
If you can you may be able to fish it out.
Your distributor has a drive shaft that goes from the dist to the oil pump in the oilpan.
Hopefully it is sitting on top of the shaft.
Their are know oil lines at the bottom of you engine, everything is internal.
If you cant fish them out from the top, the oilpan will have to be removed.
I think your best bet is to try to remove the pieces from the dist hole with a magnet on a shaft or maybe very sticky tape on a shaft.
Good luck, Robert

May 05, 2017 | 1999 GMC Jimmy

1 Answer

Crv shut down oil cap lefted off and oil all over engine and truck shutn down checked and found oil fill the spark channel and boots so replace the gasket and plugs and cleaned off the wires and now have...


have you put a new set of plug wires on it. use a spark plug tester, and put it between plug wire and dist, cap. if it is sparking you will see it. if yes and not to plugs put on new plug wires. good-day ! if above checks out. remove dist, cap and see if shaft of dist, is turning. some of the hondas have a plastic type drive gear on bottom of dist, shaft. that goes bad.

Sep 21, 2011 | 2000 Honda CR-V

2 Answers

Where is the oil pump located on a 2007 Volkswagon Jetta


its located inside the engine there is an oil tank type under the engine with about 15 to 20 bolts this is called sump you have to remove it to get to the oil pum But dont try this at home its a technicians job

Feb 02, 2011 | 2007 Volkswagen Jetta 2.5 Sedan

1 Answer

97 pontiac transport/where does oil pump drive from?


irt runs off of a shaft that is turned by the camshaft, mistakenly called a dummy shaft, actually call the oil pump drive shaft. in earlier designs of this engine, the distributor lived in the hole where this shaft goes. it can be found under the throttle body. it kind of looks like it has a freeze plug in it.

Dec 22, 2010 | Pontiac Trans Sport Cars & Trucks

2 Answers

How do u set the timing on a oil pump for a 76 harley sportster xlh 1000 lay down pump


On the oil pump shaft housing, just below the gear, there's a small square slot cut out of the housing. If you rotate the oil pump shaft, you'll see a dot on the shaft. You want this dot on the shaft in the slot in the housing when the Top Dead Center mark is in the timing hole on the other side of the engine. You have to install the oil pump like you would a distributor. You turn the dot away from the hole and when you put the pump into position, the oil pump drive gear turns the shaft while the pump goes up on the studs. When you get seated, the marks should be aligned.

Good Luck
Steve

Oct 27, 2010 | 1979 Harley Davidson XLH 1000 Sportster

1 Answer

Oil loss when removing drive shaft seal 55 plate fiesta zetec


You may lose a little, nothing major. Add in the transmission filler tube, where the dipstick goes.

Mar 13, 2010 | 2005 Ford Focus

1 Answer

Micra gear box Cv joint relacement


this easy, drain oil from gear box remove that drive shaft (u need a ball joint splitter)
replace gearbox seal, pry out old 1 with screw driver, gently tap new in, oil edge of new seal 1st. replace oil, ps dont leave to long as will damage gearbox when lack of oil

Aug 09, 2009 | 1994 Nissan Sentra 4-Door

Not finding what you are looking for?
2008 Suzuki Boulevard M109R Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...