Question about 2011 Harley Davidson FLHX Street Glide

1 Answer

How to test codes on harley - 2011 Harley Davidson FLHX Street Glide

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

Press and hold the trip odometer reset switch while turning the IGN ON to enter diagnostic mode, release the trip odometer reset button and "diag" will appear on the odometer display. However if "no rsp" appears instead then you either do not have the RUN/STOP button in the ON position or if it appears after the PSSPtbhas appeared then the particular module that "no rsp" is displacing is not present on the motorcycle. THEN press and release the trip odometer reset button again and "PSSPtb" will appear on the odometer display, the letters "PSSPtb" refer to the different modules that could display codes if the motorcycle is equipped with those modules. "P" indicates ECM codes; "S" indicates TSM/TSSM/HFSM codes; 'SP" indicates Speedometer codes; "t" indicates Tachometer codes; and "b" indicates ABS codes. If you rapidly press and release the trip odometer reset button you can cycle through all of these letter(s) one by one and they will flash as you do so. Once a letter is flashing its corresponding module has been selected to show codes on the odometer display. When a letter is displayed and flashing if you press and hold the trip odometer reset button, if there are no stored DTC's"none" will appear on the display. If any DTCs are stored in the module, whether current or historic, they will be displayed on the odometer. If you the rapidly press and release the trip odometer reset button you can cycle through all of the stored DTCs. If "no rsp" is displayed move on to the next module and when you get to the last module the display will show "end". If you want to clear all DTCs for any module press and hold the trip odometer reset button and they will all be erased from the computer memory. If at the end of a display of DTCs you want to progress to the next step or sequence for that module, quickly pressing the odometer reset button will cause the module part number to be displayed. After that display if you again quickly press and release the trip odometer reset button the display will move on to the next module display in the sequence of modules. When you are finished and wish to exit the diagnostic mode simply switch off the ignition or run switch.
continue to the next module.

If you want to do a quick of instrument function, a "WOW" test can be performed by entering the odometer self-diagnostics. In this test the background lighting should illuminate, the gauge needles should sweep their full range of motion, and the indicator lights that are controlled by the serial data circuit (the battery, the security and the check engine) should illuminate. If the instrument fails "WOW" test, check for a poor battery condition or connections and/or a poor ground connection condition and check for proper ignition voltage to the instrument. If any feature in the speedometer or tachometer is non-functional, you will have to check further into that/those area(s).

Posted on Oct 18, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electrical Problem


Hi Kurtis, there are a few things you can try 1. an alarm reset 2. see if you can retrieve any trouble codes that may have been generated by this issue. 3. Double check your fuses with a test light for continuity, for more information about your question please visit the website below. Good luck and have nice day. you can also reach me at xlch@mail.com
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...
Harley Diagnostic Codes 04 to Present

Jun 12, 2015 | 2004 Harley Davidson FLTRI Road Glide

1 Answer

My voltage guage shows discharge


Hi Anonymous, check your battery terminals and connections, especially the negative cable at both ends, make sure they are clean and tight. Have a battery load test done along with a charging system test. To help point you in the right direction please visit the website below:
Harley Trouble Codes
Good luck

Mar 24, 2014 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Codes harley paint


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day.Harley Davidson Motorcycle Paint VMR Paints
Harley Davidson Motorcycle Paint ColorRite
Original Harley Davidson Color Tones
Looking for paint codes please Harley Davidson Forums
Harley

Oct 03, 2013 | 2010 Bajaj Pulsar 135 DTSi

1 Answer

Harley sportster ignition relay test won't start


Hi Anonymous, and the usual suspects are:
1.Ignition/Light Key Switch not in IGNITION position.
2.Engine Stop switch in the OFF position.
3.Discharged battery, loose or corroded connections check negative cable at both ends. (solenoid chatters).
4. Bank Angle Sensor tripped and Ignition/Light Key Switch not cycled to Off and then back to on.
5. Starter control circuit, relay or solenoid faulty.
6. Electric starter shaft pinion gear not engaging or over-running clutch slipping.
7. Security alarm not disarming
For a prime suspect please visit website below and good Luck.
Harley Davidson Sportster error codes and how to access them
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Apr 13, 2013 | Harley Davidson XL 1200 S Sportster Sport...

1 Answer

2004 harley davidson sportster engine codes d1a9, p55pe, pn68920-olc, 61006,61007,67436-04 , appear when in diagnostic mode can anyone help explain any of these codes


Hi Jarrid, call, take a ride or trailer your bike over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary/possible and offer professional advice and assistance concerning your issue. Good luck have a nice day.

Oct 27, 2012 | 2004 Harley Davidson XL 883C Sportster...

1 Answer

Finding codes harley davidson code master


Hi Mark, take a ride or drive over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary and offer professional advice and assistance concerning your issue. Have a nice day.

Aug 11, 2012 | 2003 Harley Davidson FLHR Road king

1 Answer

09 harley iron codes are po132 & po152


Hi Anonymous, call, take a ride or trailer your bike over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary/possible and offer professional advice and assistance concerning your issue. Good luck have a nice day.

May 15, 2012 | 2009 Harley Davidson XL 883 Sportster 883

1 Answer

2002 ultra classic starts then stalls, cleared trouble codes with code reader. code p-1009 still present =''incorrect password''. tried e.c.m and security fuse removal, to reboot for 10 min then reinstall...


Hi Russellsteve, take a ride or trailer your bike over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary/possible and offer professional advice and assistance concerning your issue. Good luck have a nice day. Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Mar 19, 2011 | 2002 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Is there a way to read trouble codes on a 95 harley ultra without a scanalizer


Hi P_coldman, I don't think so but call or take a ride or trailer your bike over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary/possible and offer professional advice and assistance concerning your issue. Good luck have a nice day.

Jul 28, 2010 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

Engine light 2002 flhrci


Hi Davidfougere, for more information about your question please visit the websites below. Good luck and have nice day.
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Apr 23, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

Not finding what you are looking for?
2011 Harley Davidson FLHX Street Glide Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...