Question about 2009 Harley Davidson FXD Dyna Super Glide

1 Answer

Tsm Engine will not crank over on start control switch,no indicators and engine had increased in idle by 100 rpm . Engine will run if you push start bike

Posted by on

  • pete_623 Apr 20, 2014

    Also bikes indicators have stopped working

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Check your battery cells individually. Get a cheap little Fluid eyedropper type tester. If there is one cell that is showing dead, it's a write off, get a new battery. The Yasa battery company can give you the PROPER number codes for your bike. You may have a battery with an under requirement amp hour rating. Some shops just sell you what fits. It still runs because the stater runs the ignition system and my even run your lights fine. If it is a bad battery don't just fling one in and go. get the new battery fully charged with a 2 amp charger and test those cells too. They must be fully charged. Do not just wing it. Battery's have a sort of memory. Once you begin to use that battery, it will only ever charge to the point it 'remembers'. you need a strong battery to turn over a Harley. Fill the new battery , charge it then level up the acid to the marks. Can't see the marks cause it's a black one? Put a Maglight or other strong flashlight against & behind it and you'll see the acid level. All else fails, visually make sure each cell has acid over the lead plates.

Posted on Apr 21, 2014

Testimonial: "Just doing the checks you have suggested will post what I find thanks"

  • 2 more comments 
  • pete_623 Apr 23, 2014

    Did the checks you suggested battery is fine no dead cells ,charged battery with trickle charger to fully charged ,it made no difference to the electric starting of the bike, also no difference , I suspect that the problem is in the tsm,however not able to 100% confirm that my tsm has died.

  • kellycalk
    kellycalk Apr 25, 2014

    Tell me what a tsm is and I may be able to assist further. I stopped working on Harley's in the early evo days. Not a problem though. I still have the mind goin ok.

  • pete_623 Apr 25, 2014

    Tsm is turn signal module , has bank angle sensor incorporated in it which can cause this problem ,no indicators and no ignition if it has failed

  • kellycalk
    kellycalk Apr 25, 2014

    Ok I looked into it a bit. Sounds like the culprit ok. Replace it.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: Bike ran great engine was at running temperature.

If you have the on off and reserve petcock or fuel valve then its not the old vacuum type. If battery good time to check basics so you see fuel squrting into the engine through the carb when throttle turned ? do you actually have spark at the plugs ?

Posted on Jul 23, 2009

OneRide
  • 379 Answers

SOURCE: I have a 2000 fxst--when i start the bike and rev

2 things, bad speedo or your speed sensor picked up some metal. Or both. The sensor is located on the right side on the trans.Pull one allen bolt and GENTLY pry the sensor out. Wipe off the metal shaving. The speed sensor is MAGNETICALLY triggered, so it picks up metal from the trans and shorts out. Possible bad wiring connection somewhere too.

Posted on Jul 08, 2009

wd4ity
  • 4565 Answers

SOURCE: High Idle On Start-up.

Most fuel injected motorcycles do start up in a "fast idle" mode. Although I don't know much about fuel injection on Harleys (H-D will not tell you much about it unles you are one of their technicians), I don't think the system is equipped with an engine temp sensor. Since the crank case sensor get it's pulses from pockets cut into the outer edge of the left side flywheel half, the sensor will have oil on it.

Posted on Sep 24, 2009

v2iper
  • 150 Answers

SOURCE: High idle on start-up

Its your idle senser sits on top of the manifold u will see it looking at u when u take off air filter cover. Little black plastic.plug in.

Posted on Dec 20, 2009

  • 623 Answers

SOURCE: engine idle increases 200/300 r.p.m. after engine is hot.?

Vacuum leak?

Posted on May 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i bring my idle rpm down on my 2002 cam 88


Ensure that the engine is warmed up to normal operating temperature and the enrichener knob is pushed all the way in BEFORE adjusting engine idle speed. It is possible for a properly warmed up engine to idle above the normal idle range of 950-1050 RPM with the enrichener knob pulled PARTIALLY OUT. If the bike has no tachometer attach one or attach a DIGITAL MULTIMETER equipped with an RPM INDUCTIVE PICKUP over front spark plug cable to monitor engine RPM. Then start the motorcycle engine and let it run until it reaches normal operating temperature with enrichener knob pushed fully in (enrichener closed). Then set the idle speed to 950-1050 RPM using a special CARBURETOR IDLE ADJUSTER and tip. Turn clockwise to increase idle speed and turn counterclockwise to decrease idle speed. The throttle stop screw in on the right or front side of the CV carb.

May 30, 2014 | 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

My aprila rs50 starts fine and runs fine cold but if it heats up abit you pull the throttle and it sounds like its dieng


Instructions
    • 1 Park your RSV 1000R on a well-ventilated, level area, using its kickstand.
    • 2 Start the engine and let it idle in place until the temperature gauge built into the instrument cluster indicates a minimum internal temperature of 180 degrees Fahrenheit. This is the motorcycle's ideal operating temperature.
    • 3 Take note of the engine idle speed, using the tachometer needle, while the engine is running. Ideally, the engine should idle steadily at 1,250 rpm.
    • 4 Adjust the engine idle speed to 1,250 rpm, using the idle adjuster screw hidden between the lower right edge of the fuel tank and the upper edge of the right middle fairing panel. Turn the idle adjuster screw clockwise to increase the engine idle speed, or counterclockwise to decrease the engine idle speed, using a small flat screwdriver if your RSV 1000R's frame (VIN number) precedes ZD4MEE009YS000292. A plastic knob allows the engine idle speed to adjusted by hand on RSV 1000R models with a frame (VIN) numbers starting from ZD4MEE009YS000293.
    • 5 Rev the engine two to three times and observe the tachometer. The engine should return to a 1,250 rpm idle. Adjust the engine idle speed as needed, using the method described, then rev the engine again. Problems may exist within the throttle control, fuel-injection system or engine, if the engine idle speed will not hold steady at 1,250 rpm. Contact your local Aprilia service facility for assistance.
    • 6 Stop the engine, once you have obtained a steady 1,250 rpm idle speed.

Jan 17, 2013 | Aprilia Motorcycles

1 Answer

Water is not getting into the head


Instructions
    • 1 Park your RSV 1000R on a well-ventilated, level area, using its kickstand.
    • 2 Start the engine and let it idle in place until the temperature gauge built into the instrument cluster indicates a minimum internal temperature of 180 degrees Fahrenheit. This is the motorcycle's ideal operating temperature.
    • 3 Take note of the engine idle speed, using the tachometer needle, while the engine is running. Ideally, the engine should idle steadily at 1,250 rpm.
    • 4 Adjust the engine idle speed to 1,250 rpm, using the idle adjuster screw hidden between the lower right edge of the fuel tank and the upper edge of the right middle fairing panel. Turn the idle adjuster screw clockwise to increase the engine idle speed, or counterclockwise to decrease the engine idle speed, using a small flat screwdriver if your RSV 1000R's frame (VIN number) precedes ZD4MEE009YS000292. A plastic knob allows the engine idle speed to adjusted by hand on RSV 1000R models with a frame (VIN) numbers starting from ZD4MEE009YS000293.
    • 5 Rev the engine two to three times and observe the tachometer. The engine should return to a 1,250 rpm idle. Adjust the engine idle speed as needed, using the method described, then rev the engine again. Problems may exist within the throttle control, fuel-injection system or engine, if the engine idle speed will not hold steady at 1,250 rpm. Contact your local Aprilia service facility for assistance.
    • 6 Stop the engine, once you have obtained a steady 1,250 rpm idle speed.

Jan 17, 2013 | 2002 Aprilia RS 125

1 Answer

89 cutlass cierra crank but wont start when wet out unless gas pedal is pushed


This should be a drive by wire vehicle meaning it has a cable for the throttle body. First thing would be to see if any error codes can be pulled up (most parts stores will do that for free.) Drive by wire versus the late model that use electronic control for the idle have a IAC or idle air control which when first started controls the idle air intake--all air is run by it to idle the vehicle when cold--

Usual symptoms are rather high idle when cold engine or even idle and RPM jumping up and down and stalling when cold.

Another way if idle does drop when cold is tapping the gas--engine will still run until hot. Means not usually a fuel pump issue.

You could also have if the vehicle is fuel injected a dirty Mass air flow sensor, a throttle position sensor, etc.

These can be if the vehicle has them cleaned using a special zero residue spray cleaner.

First have it scanned to see what if any errors it shows--the computer.

Dec 17, 2012 | 1989 Oldsmobile Cutlass Ciera

1 Answer

I have a 2008 mercury Milan with nearly 60k miles on it. When I come to a stop the rpm drops by 1000 then recovers quickly. What should I do to fix the problem? Any suggestions will be greatly appreciated.


Check out related help links to troubleshoot these problem:----Click the link below:---Idles Fine but RPM jumps in drive mode? http://technoanswers.blogspot.in/2012/07/idles-fine-but-rpm-jumps-in-drive-mode.html
---------Mitsubishi Lancer rpm needle bounces? http://technoanswers.blogspot.in/2012/02/mitsubishi-lancer-rpm-needle-bounces.html
--------How to adjust rpm on 2009 dodge charger SRT8?


http://schematicsdiagram.blogspot.com/2011/12/how-to-adjust-rpm-on-2009-dodge-charger.html
---------
Engine cuts out at 3000 RPM? http://schematicsdiagram.blogspot.com/2011/12/engine-cuts-out-at-3000-rpm.html

---------

Cold start problem and vehicle shudder around 2500 to 3500 rpms
http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

---------
High rpm in neutral? Inconsistant high RPM in neutral? http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-----------
Jetski Sputters and Low RPM? http://whatisbyme.blogspot.in/2012/07/jetski-sputters-and-low-rpm.html

--------
Fuel Injection Problem And RPM suddenly increases http://whatisbyme.blogspot.in/2012/07/fuel-injection-problem-and-rpm-suddenly.html

----------
2005 Toyota Highlander: Engine runs hard RPM below 3000? http://whatisbyme.blogspot.in/2012/05/2005-toyota-highlander-engine-runs-hard.html

---------
1987 Toyota Camry: RPM Drops going Up hills? http://whatisbyme.blogspot.in/2012/05/1987-toyota-camry-rpm-drops-going-up.html

-----------
Cruise Control stops working, Excessive cranks to start the engine and RPM goes max 2500 http://whoisbyme.blogspot.in/2012/07/cruise-control-stops-workingexcessive.html

----------
1990 Toyota 4Runner: Engine cuts off when reaches 2000 RPM?


http://whatisbyme.blogspot.in/2012/05/1990-toyota-4runner-engine-cuts-off.html

------------
1999 Toyota Camry: Erratic stalling and high engine RPM at idle?


http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-erratic-stalling-and.html

---------
1995 Toyota LS: Misfire at idle or low RPM http://whatisbyme.blogspot.in/2012/04/1995-toyota-ls-misfire-at-idle-or-low.html

-----------
Lexus RX: Tapping noise under Valve Cover At Low RPM? http://technoanswers.blogspot.in/2012/04/lexus-rx-tapping-noise-under-valve.html

----------
These will help.
Thanks.

Nov 22, 2012 | Cars & Trucks

1 Answer

How to raise the idle 100 rpm on ford f150 5.4


have your idle air control motor cleaned. there are no idle adjustments on this engine. typically the idle air control valve becomes gummed up with carbon. while cleaning the valve you may also want to clean the mass air flow sensor. you will need special cleaners for both which can be purchased at any auto parts store.

Aug 30, 2012 | 2005 Ford F-150

3 Answers

My car seems to cut off at random times..mainly after i have taken my foot off of the accelerator. What could be causing this problem ?


Here is the common cause of surges, stalls at stops, slow idle speed, erratic idle speed, rough idle and engine hesitation (and other problems), it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Jul 23, 2009 | 1996 Cadillac DeVille

1 Answer

Ideling 1600 rpm onlywhen engine warm


please change the idling switch control valve assembly plus the sensor!

Jun 18, 2009 | Mercedes-Benz SL-Class Cars & Trucks

1 Answer

Rough idle stalls at low rpm's


hello first check your idle with the car running foot on brake see were your rpm reading is if your below 500rpm check your label underhood for your curb idle setting second see if theres a adjustment screw you can increase were your gas cable lever rest against your set screw underhood if you feel confident enough remove your iac motor idle air control valve if the bore were the end of the pintle extracts out to close has varnish builup our carbon it will stick creating vacuum leak type senario causing stalling rough idle sometimes even no start conditions good luck

Sep 14, 2008 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
2009 Harley Davidson FXD Dyna Super Glide Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...