Question about 2006 Victory Vegas Jackpot

Open Question

Rear hub diagram

Rear hub broke all 6 bolts can u bye just the new hub

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

2 Answers

How do I get bolts out that have broken off so that I can replace the strutts on both sides in the rear of the car?


you need to go to auto parts plqse and purchase some liquid wrench and spray down all rusty bolts that you need to replace.let it sit for a while so it can penetrate. take your old broken bolt with you and purchase a drill tap that you can drill out the bolts .this is the same process you use when brake off head bolt.

Jun 03, 2014 | 2001 Mercury Sable

1 Answer

Need diagram of rear end for 2001 yukon XL 4x4


IF you have a axle flange that is bolted to the hub by say 6 nuts then undo the nuts and you will see small tapers around the bolts. To loosen these give the centre of the axle flange a good hard hit with a hammer. This will pop the tapers loose and allow you to get them out . Pull the axle out and you will find 4 nuts with a lock tab washer between them. If you have have discs you will need to remove the caliper first then pull the hub off.

Apr 15, 2013 | Vehicle Parts & Accessories

1 Answer

Rear passenger axle needs replaced


A Sunfire is front wheel drive, so there should not be a rear axle.
There is a rear strut, the hub and bearing is bolted to the trailing arm and strut. The tire and wheel bolt to the hub.
I would get two estimates for repairs before making a decision. It could have under-body damage too.

Jun 26, 2012 | 2001 Pontiac Sunfire

1 Answer

1996 caravan broke all bolts free hub assembly still will not


Rear hubs? according to book, need a special tool to pull them... according to a loal shop, bang on it til it releases... you will need to replace it anyways.... might look for a rental place that rents the tool.

Peace

Feb 27, 2010 | 1996 Dodge Caravan

1 Answer

Repair broke upper shock bolts on the rear shocks


Jack the car up bye the body and jack up the axle and tap the bolt out if not air hammer.
Heat the bolt with butane tourch.

Jan 15, 2010 | 1999 Jeep Cherokee

1 Answer

How do you remove the backing plate from an '05 Chev Venture rear hub so the hub can be replaced?


The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure
  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the brake drum.
    1. Remove and DISCARD the wheel bearing/hub bolts.
    2. Remove the wheel bearing/hub.
    3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
    4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Nov 07, 2009 | 2005 Chevrolet Venture

1 Answer

How to replace lug studs on 2002 chrysler town


I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Jul 08, 2009 | 2009 Chrysler Town and Country

1 Answer

Broken wheel bolt


These bolts are usually pressed into the hub. If you remove the hub you can usually knock out the broken bolt and buy a new one at an auto parts store and insert it into the hub, When you put the hub back on the wheel and tighten the lug nuts that will pull the new bolt up tight into the hub.

This is usually caused by someone using an powered wrench tightening the wheel nuts too tight. I had this happen to me once and ever since I have insisted that anyone using an air wrench do not use one to tighten the lug nuts. They must use a torque wrench and tighten to manufactures spec.

Good luck and I hope this helps

Loringh

Oct 14, 2008 | 1990 Ford F250

Not finding what you are looking for?
2006 Victory Vegas Jackpot Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...