Question about 1979 kawasaki KZ 1300 A1

1 Answer

Are the washers that secure the shock absorbers supposed to be larger than the upper and lower holes on the shock's that have rubber inserts

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 408 Answers

The washers must have outer diameter big enough to cover all of the rubber surface and inner diameter as large as the bolt diameter.

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear shocks


Removal & Installation

  1. Raise and safely support the vehicle.
  2. Support the rear axle and slightly lower the vehicle enough to lessen tension on the shock absorber.
  3. Remove the lower shock absorber retaining nut and washer.
  4. Disconnect the lower end of the shock absorber from the mounting stud.
  5. Remove the shock absorber upper end retaining nut and washer.
  6. Remove the shock absorber from the vehicle.
To install:
  1. Install the shock absorber onto the upper and lower mounting studs of the vehicle.
  2. Install the washers and retaining nuts. Tighten the upper and lower retaining nuts to 22-30 ft. lbs. (30-41 Nm) on 2001-02 models or 22 ft. lbs. (30 Nm) for the upper bolts and 47 ft. lbs. (64 Nm) on the lower bolts.
  3. Lower the vehicle.

Jul 07, 2014 | 2004 Nissan Quest

1 Answer

What torque specs do u tighten the front shock absorbers nuts to


adjust the nuts until there is tension placed on the rubbers. You will see the rubber start to slightly bulge out under the washers and that will be the correct tension

Dec 18, 2013 | 2000 Jeep Grand Cherokee

1 Answer

How do you change the rear shocks


Support the rear suspensionfrom under the lower suspension arm.
Remove shock absorber upper nut, washer and bushing
Remove lower shock absorber nut and washer.
Remove shock absorber.
Reverse steps to install.

Jan 08, 2011 | 2004 Hyundai Santa Fe

1 Answer

Dear Sir, How do you change an 87 mitsubishi mighty max front shocks without any compression equipment? Please email me at brad8141@hotmail.com. Is there a book with instructions regarding this...


REMOVAL & INSTALLATION
  1. Support the vehicle safely on jackstands. Support it at a height which will allow sufficient room to reach the upper shock absorber mount.
  2. Remove the wheel.
  3. Remove the upper shock nut, washer and bushing.
  4. Remove the lower mounting bolt(s) and remove the shock from the vehicle.
  5. Install the shock absorber in the vehicle and loosely tighten the upper shock absorber nut. Make sure the install the bushings and washers before installing the upper nut.
  6. For 4WD vehicles, install the shock absorber so that the white paint mark at the lower side of the shock absorber faces the outer side of the vehicle. Install the lower shock absorber bolt(s). On 1992-95 Montero torsion bar suspensions, tighten the single lower mounting bolt and nut to 65-76 ft. lbs. (88-103 Nm). On all other vehicles (whether torsion bar or coil spring suspensions), the two lower shock absorber mounting bolts should be tightened only to 7-10 ft. lbs. (9-14 Nm). Fig. 1: Install the shock absorber so that the white mark faces toward the outside of the vehicle - 4WD vehicles, except 1992-95 Monteros 86668006.gif
    Fig. 2: Install the bushings, washers and nuts in the order shown - except 1992-95 Monteros 86668007.gif

  7. On 1992-95 Monteros, tighten the shock absorber installation nut so that the dimensions shown in the illustration ( A and B) are at the standard values. These standard values are: A - 0.04-0.08 in. (1-2mm), B - 0.06-0.10 in. (1.5-2.5mm). WARNING
    When tightening the nut, be careful not to bend the stud pin of the washer assembly.
  8. On all other vehicles, once the lower mounting bolt(s) are tightened, tighten the upper shock absorber mounting nut all the way to the end of the thread on the shock absorber stud, then tighten the locking nut to 9-13 ft. lbs. (12-18 Nm).
  9. Install the wheel.
  10. Lower the vehicle to the ground. Fig. 3: When installing the upper shock nuts on 1992-95 Monteros, make sure measurement A is 0.04-0.08 in. (1-2mm) 86668008.gif
    Fig. 4: When installing the upper shock assembly, make sure its components are positioned as shown - 1992-95 Monteros 86668009.gif
prev.gif next.gif

Nov 03, 2010 | 1987 Mitsubishi Mighty Max

1 Answer

How to change 2007 dodge 1500 front struts?


Removal & Installation Independent Front Suspension – 2WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Support the lower control arm outboard end.
  4. Remove or disconnect the following:
    • Upper shock absorber nut, retainer and grommet
    • Lower nuts and shock absorber
To Install:
  1. Install or connect the following:
    • Lower retainer and grommet on the shock absorber stud and insert shock absorber through frame bracket hole
    • Lower nuts
      1. Torque to: 25 ft. lbs. (34 Nm)
    • Upper grommet, retainer and new nut (or existing nut with Mopar Lock N Seal or Loctiti 242) on the shock absorber stud
      1. Torque to: 40 ft. lbs. (54 Nm)
  2. Remove support from lower control arm outboard end.
  3. Lower the vehicle.
Independent Front Suspension – 4WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Remove tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove or disconnect the following: dod_ram15_02-04_4wd_shock.gif

    • Upper shock nut with insulator and retainer
    • Lower shock bolt
    • Shock absorber
To Install:
  1. Install or connect the following:
    • Upper part of shock absorber into frame bracket with insulators and retainers and nut
      1. Torque to: 40 ft. lbs. (54 Nm)
    • Lower part of shock absorber into lower control arm with the bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
  2. Remove support from lower control arm.
  3. Install tire and wheel assembly.
  4. Lower the vehicle.
Link/Coil Front Suspension To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Nut, retainer, and grommet from upper stud in engine compartment dod_ram15_02-04_shock.gif

    • Nuts from upper shock bracket
  3. Lower bolt from axle bracket and shock absorber from engine compartment
To Install:
  1. Position lower retainer and grommet on upper stud and insert the shock through the spring from the engine compartment.
  2. Install or connect the following:
    • Lower bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
    • Upper shock bracket and nuts
      1. Torque to: 55 ft. lbs. (75 Nm)
    • Upper grommet, retainer and upper shock absorber nut
      1. Torque to: 35 ft. lbs. (47 Nm)
prev.gif next.gif

Jul 22, 2010 | 2007 Dodge Ram Truck

1 Answer

How do I change the front and rear shocks on my 99 cherokee?


FRONT:
Removal & Installation
  1. Remove the nut, retainer and grommet from the shock stud in the engine compartment.
  2. Raise and support the front axle.
  3. Remove the lower mounting nuts from the axle bracket.
  4. Remove the shock absorber.
To install:
  1. Position the lower retainer and grommet on the shock stud. Insert the shock absorber through the shock tower hole.
  2. Install the lower shock studs into the axle bracket.
  3. Install the mounting nuts and tighten to 250 in. lbs. (28 Nm).
  4. Remove support and lower the vehicle.
  5. Install the upper grommet, retainer and nut on the stud in the engine compartment.
Rear:

Removal & Installation
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove or disconnect the following:
    • Upper locknut and washer from the frame bracket stud, on the Grand Cherokee
    • Lower bolt, nut and washers from the axle shaft tube bracket
    • Shock absorber
To install:
  1. Place the shock absorber upper end in position and tighten the fasteners to the following specifications:
    • Cherokee: 17 ft. lbs. (23 Nm)
    • 1999–01 Grand Cherokee:68 ft. lbs. (92 Nm)
    • 2002–04 Grand Cherokee: 80 ft. lbs. (108 Nm).
    • 2005 Grand Cherokee: 70 ft. lbs. (95 Nm).
  2. Place the shock absorber lower end in position and tighten the fasteners to the following specifications:
    • Cherokee: 46 ft. lbs. (62 Nm)
    • 1999–01 Grand Cherokee:68 ft. lbs. (92 Nm)
    • 2002–05 Grand Cherokee: 115 Nm (85 Nm).
    please do not hesitate to ask any further questions about your vehicle i would be glad to help you.
  3. do not forget to rate and comment about your experience with fixya...


Dec 27, 2009 | 1999 Jeep Cherokee

1 Answer

How to replace front shock bsorbers


This is for the 2WD model:

2-Wheel Drive
  1. Raise and support the front of the vehicle safely using jack stands.
  2. Using an open end wrench, hold the shock absorber upper stem to prevent it from turning, then remove the upper stem retaining nut, the retainer and rubber grommet.
c16056c.gif
Common front shock absorber mounting-2WD vehicles

  1. Remove the shock absorber-to-lower control arm retaining bolts and lower the shock absorber assembly from the bottom of the control arm.
  2. Inspect and test the shock absorber; replace it, if necessary.
To install:
  1. Fully extend the shock absorber stem, then push it up through the lower control arm and spring so that the upper stem passes through the mounting hole in the upper control arm frame bracket.
  2. Install the upper shock absorber nut and tighten to 100 inch. lbs. (11 Nm) on 1994 models 145 inch lbs. (16 Nm) on 1995 models, 54 ft. lbs. (73 Nm) on 1996 models, or 106 inch lbs. (12 Nm) on 1997-99 models while holding the stem with an open end wrench. Be careful not to crush the rubber bushing.
  3. Install the shock absorber-to-lower control arm retaining bolts and tighten to 20 ft. lbs. (27 Nm) on 1994-95 models and 54 ft. lbs. (73 Nm) on 1996 models, or 22 ft. lbs. (30 Nm) on 1997-99 models.
  4. Remove the jack stands and carefully lower the vehicle.

Nov 01, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

1 Answer

Shocks


rear
5955ba5.gif ------------------------------------------------------------------------------------------

front

Removal
  1. Remove front shock absorber-to-upper shock bracket nut and bolt.
  1. Disconnect the lower end of the front shock absorber bolt and nut from the U-bolt plate.
  1. Compress the front shock absorber and remove.
Installation
  1. Insert front shock absorber into the front shock absorber mounting bracket (18183). Insert bolt and tighten nut to 60-81 Nm (45-60 lb-ft).
  1. Attach the lower end of the front shock absorber to the U-bolt plate by installing the nut and bolt. Tighten to 60-81 Nm (45-60 lb-ft).
---------------------------------------------------------------------------------------------

front


Feb 04, 2009 | 1996 Ford F350 Crew Cab

1 Answer

Information on how to change rear shock absorbers


with great difficulty,three bolts hold the plate that takes the top bush/mounting .jack vehicle up and support with axle stand .Another jack under rear axle ,jack this one up till cars starts to lift then fit the spring clamps and compress the spring.Next undo the 3/4 13mm headed bolts that hold the plate to the chassis ,if you can release them???---??? ,then next using a small bottle jack take the strain on the bottom of the shock absorber and then remove the bolt ,lower the jack and the top one will lower as well ,undo the two nuts on the top mounting and pull the old shock absorber out .Or what i do if back is dancing and thats to do as above to support vehicle ,support lower of shock absorber ,remove the bolt and then jack it up ,then drill a small hole about an inch from the top of the tube and then thread it ,refill the shock absorber with a heavier oil like dextron .fit a bolt into the hole with a rubber washer and its as good as new

Aug 12, 2008 | Jaguar XJ6 Cars & Trucks

Not finding what you are looking for?
1979 kawasaki KZ 1300 A1 Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...