Question about 2001 kawasaki KLX 250

Open Question

Removing carb klx250

How to remove carb

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bypass ignition switch


Hi, Ricky I am sorry you can't find the first and best tool you ever bought for your Kawasaki but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
http://mototh.com/files/kawasaki/KLX250/Kawasaki-KLX250-Service-Manual_new.pdf

Nov 29, 2015 | kawasaki KLX 250 Motorcycles

1 Answer

Remove carb


Remove air cleaner Remove torx screws in carburetor throat. Remove air cleaner backing plate. Turn off gas valve. Remove fuel line from carb. Pull carb from manifold. Release throttle cables. When re installing carb backing plate, put Loctite Blue on torx screw threads.

Sep 25, 2013 | Harley Davidson FXSTS - FXSTSI Springer...

1 Answer

Klx250 wont run it has spark new battery and cleaned carby but wont fire up will occasionaly start and run fine


Remove the filter or filter connection to the back side of the carb and spray it with starter fluid. If it starts when you do that each time, the carbs still have a problem and need to be cleaned out again or adjusted correctly.

Jan 17, 2013 | 2005 kawasaki KLX 250

1 Answer

How to remove carburetor from 235 husqvarna chain saw


Start by removing the 3 anti vib spring screws, one on the front underside of the saw, one at the rear underside of the saw, and one at the r/h side of the cylinder, remove the 3 screws holding the l/h side of the rear handle and remove the plastic trigger and throttle lock, the handle and spine will now come away as an assembly from the rest of the saw, now remove the screw at the top r/h side of the saw and remove the square orange plastic plate, once removed you will gain acess to the two 8mm nuts under the air filter securing the carb, there is also one torq screw to remove before the carb and filter bacl plate can be removed, you will also have to pull some of the fuel hoses from the carb to completly remove it.

Dec 23, 2012 | Garden

1 Answer

My husqvarna 455 rancher needs a carburetor kit how do you remove the carb


This is not so easy to explain, this is an X Torque engine so the carb does not come off so easy, there are air tubes on the back of the carb, however, remove the air filter, remove the earth cut out wire and earth return wire from the red switch, they are just push on, there is a blue clip on the throttle shaft side of the carb, gently pull out and twist ( this holds the throttle push rod into the carb ), open the throttle trigger with your finger at the same time now remove the throttle push rod from the throttle shaft, once out of the carb pull the rod toward the front of the saw and out of the tank, now unscrew the four allen headed screws from the air filter housing, and remove, ease the carb up and away far enough to remove the fuel hose, now remove completely.

Feb 18, 2012 | Husqvarna Garden

1 Answer

How do i remove the carbs from the engine?


After removing the tank and airbox, loosen the clamp screws securing each carb to the inlet stubs, these can be sometimes difficult to get at and time consuming, also unclip the idle screw from its bracket, remove the choke cable and throttle cable-s from the carbs, some models have water pipes fitted 1on each side of the bank of carbs, once removed have a screw ready to push into the pipe to stop the coolant leaking, if you have difficulty undoing the screws securing the carbs, grasp the bank of carbs from behinde, at the top pulling towards you normaly is enough to remove them as the retaining screws are not always tightly secured but often difficult to see, once removed you can
then prepare the screws ready for re fitting the carbs

Apr 17, 2011 | 2001 kawasaki ZX-6R Ninja

1 Answer

Wont crank after sitting for a month,will flood.2009 klx250 COULD IT BE A FOULED PLUG?


sounds like the pet **** needs to be turned off and the carb needs to be run out of fuel before you put it up in storage

Apr 10, 2009 | 2007 kawasaki KLX 250

1 Answer

PROCEDURE FOR CHANGING ELECTRIC STARTER FOR KLX250 1999


dissconnect the battery locate the starter there should be two bolts holding it on remove them and disconnect the wire and install your new starter

Jan 14, 2009 | 2001 kawasaki KLX 250

Not finding what you are looking for?
2001 kawasaki KLX 250 Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...