Question about 2004 kawasaki VN 1600 Mean Streak

Open Question

How to replace fork seals - 2004 kawasaki VN 1600 Mean Streak

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 132 Answers

SOURCE: how to replace fork dust and oil seals on a kx125

i would do the same as the other post has said, but i would use the old seal to drive the new seal in with a rubber mallet that way you cant damage the fork.

Posted on Apr 28, 2009

  • 8 Answers

SOURCE: fork seals

You need a manual and there are special tools required to change the seals. Let the dealer do it.

Posted on May 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 harley street bob fork seal replacement


I have never seen seals replaced without dismantling the forks. The seal will come in a fork revbuild kit whether the bushings etc are used or not. Obtained separately but necessary in any case are new lower fork bolts and copper washers. I suppose it might be possible to get the seal out of the fork leg without completely dismantling the fork but the normal way of removing the seal is to use the slider as a slider hammer tool to drive the upper bushing and seal from the fork leg which requires removal of the lower bolt and washer and pretty much fully dismantling the fork. You will also need a special fork holder tool or at the least a pair of vise soft jaws and it is critical how much fork oil is added back into the fork as too much will make the ride unacceptably hard and too little will allow the fork to compress too much and be too soft. You also really need an appropriate seal installer to reinstall the seal and upper bushing etc. All that being said:

May 23, 2014 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

How to fix fork seals and what are they for and how do you know when they need replaced?


Hi,,,,,,fork seals are to stop oil coming out of your forks,,,,if your forks have oil on them ,then the seals need replacing.(you cant fix them)


hope this helps

Mar 30, 2011 | Yamaha FZR 600 Motorcycles

1 Answer

My front fork seals need replacing on my 2005 model TE450, i don't know the specifications, and exactly how much oil to use in each fork


forks need to be removed,and disasemble,and cleaned,new fork seals,reasembleb fit new seals, refit damping cartridge,fill fork with 5w fork oil upto 120mm from top,refit spring, refit fork cap

Aug 14, 2010 | Husqvarna TE 450 Motorcycles

2 Answers

Replacing the front seal- located on the fork.


To replace the fork seal you must open the top of the fork and remove the spring. Then drop the fork tube out of the clamp. Once the fork tube is removed replacing the seal is simply pulling the old one off and putting the new one on. You will need to remove your front wheel.

Jun 29, 2009 | 2003 Yamaha YZF 600 R thunder cat

1 Answer

Front fork seals need replacing Honda vigor FX650


hi non usd forks are ok thers a allen key bolt at the bottom of the fork leg would be wish to change the fork guilds too thr fork seals can be prized out with a screwdirver carfully

Jun 24, 2009 | 2000 Honda Vigor FX 650

2 Answers

2004 honda shadow 600 VLX leaking fork seal bike has 600 miles on it should I replace left and right if only right is leaking.


check first to see if the leaking fork has any rust pitting on the chrome,if it has and its a very small blemish then fettle it off first,and just replace the leaking seal,as the saying goes..if it aint broke dont fix it,if the seals had been in the forks for years and the bike not used then consider replacing both..

Jun 05, 2009 | 1986 Honda VT 1100 C

3 Answers

82 honda sabre fork seal replacement


No special tools other than maybe an air-impact whench to remove the Allen bolts in the bottom of the fork sliders. These hold the botom of the metering rods into the forks and will spin if you don't have Honda's special tool which fits down the inside of the fork tube. Air wrench spins them off no problem.

V65 Sabre has fule filter behind battery and fule shutoff valve under seat.

Loosen upper triple-clamp pinch bolt before trying to remove fork cap.

Drain oil out of fork, then remove axle and access the metering rod holder bolt at the bottom inside the area whre the axles goes. Use an air wrench and appropriate Allen bit.

Remove fork cap, being careful of the spring pressure.

Remove fork from bike and take out spring and metering rod. Pry dust seal out of fork slider and use snap-ring pliers to remove retainer from beneath dust seal. Use fork tube to hammer seal and slider bushing out of fork slider.

Replace seal and use old seal to cushion it. Make a fork seal driver from split PVC pipe and hammer seal and slider bushing back in. Remove old seal and replace retainer clip. Install dust seal.

Reinstall on bike and install spring. With bike properly supported, stand on pegs and use ratchet, extension and socket to apply pressure to spring and thread cap carefully onto top of fork tube. Reinstall metering rod holder bolt in bottom of fork using thread-locker and air-wrench. Don't over-tighten; just ue high speed to conteract tendency of metering rod to spin inside slider.

Remove fork cap again and fill to appropriate level with 5 weight fork oil (Pro Honda SS-7 or equivalent). Use turkey-baster to remove excess oil to proper level (5 1/2 to 7 inches fully compressed depending on damping quality desired).

Jun 03, 2009 | 1985 Honda VF 1100 Sabre

1 Answer

Front fork leaking oil from bottom of the seal.


change the oil seals and oil in the fork,and avoid wheelies on the bike and off road biking 

May 17, 2009 | 2004 Honda CRF 250 R

1 Answer

How do i dismantle front forks to replace the oil seals


You just needed to.... remove front wheel, support bike on something, undo retaining bolts on forks, tap out fork legs from the top, using a soft mallet. Take out fork seals with a seal pick, (halfords) Replace old seal with new seals, in reverse order) sliding over the fork leg, tapping into place. Then put replace forks etc in reverse order (from dissassembly). Hope this helps

Feb 21, 2009 | 1992 Honda CB 750F2 Seven Fifty

Not finding what you are looking for?
2004 kawasaki VN 1600 Mean Streak Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...