Question about 2008 Hyosung GT250

1 Answer

Stripped oil bolt - 2008 Hyosung GT250

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyosung Master
  • 3,096 Answers

You can get a variety of oversized and other type "fix-it" plugs at Oreilly's, or AutoZone... just take your plug with you.. ( I did this very operation on my truck TODAY!)
I have put heli-coils in the engine cases also.. you have to watch it doing this.. it creates aluminum chips that get inside the case..they must be removed before running.

Posted on Jun 11, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the bar bolts?


Depends on Model. Some you will have to remove muffler, other models are actually inside of oil tank. Once you locate the Square head of the bolts, you can than tap them out gently from the other side using a hammer. Afterwards, tap new bar bolt in its place. NOTE: if bolt head is inside of oil tank you will need to drain oil first.

Jul 14, 2014 | Husqvarna 142 Chainsaw For Parts

2 Answers

Bolt is stripped can get off tried penetrating oil didn't work need help


I would use a vise-grip that fits really snug and you should be able to break it loose. You will want to replace the bolt so you don't have this problem again

Mar 02, 2013 | Cars & Trucks

2 Answers

Crankshaft pulley bolt worked its way out of end of crankshaft. Car still ran but no oil pressure. Is it possible that it was stripped when oil pump was replaced or is it more likely it was not torqued...


Either or are possible. This should be done professionally but if u want to check the threads, Get the exact bolt size including thread size (specs should be on new part, get from OEM) Try hand threading it into the crank (GENTLY) use a ratchet to feel for a stripped thread. You can do the same with a tap from a tap & die set. If is well, use threadlock on the new hardware threads. DONT FORCE IT, IF IT'S NOT STRIPPED TOURQUE TO SPEC, IF IT'S STRIPPED IT'S STRIPPED. Good luck

Aug 11, 2017 | 1985 Porsche 944

1 Answer

What to do if engine oil drain bolt lost its grooves (not tread)...whats the best solution for removing drain bolt without doing any damage?


Typically , the threads in the crankcase are what get stripped out. Find a dealer that has oversize drain bolts and have them tap the drain hole in the crankcase out to the next size bolt. That is the best fix for a stripped drain bolt hole. Always be careful, when changing your oil , to only tight the filter and the drain bolt (with soft aluminum sealing washer) enough to seal the oil in . Over tightening will only make the next oil change harder with the possibility of this happening again.

Nov 05, 2010 | 2001 Honda CBR 600 F(4)i

1 Answer

How do you change the oil pan or the oil pan bolt on a 1997 buick century?


i am assuming the bolt threads are stripped, you can get a self tapping oversize bolt from a parts store, use a new gasket

Sep 14, 2010 | 1997 Buick Century

1 Answer

1994 4runner, six cyl. putting rebuilt heads on, toyota head gaskets, new head bolts "tvs 10.9". Torqued bolts in pattern to 33 foot pounds. another 1/4 turn in the pattern. and into my next and final 1/4...


REMOVE 3 BOLTS MAKE SURE YOU HAVE THE RIGHT THREADS.IF BOLTS LOOK OKAY.YOUR BOLTS HOLES HAS DEBRIS OR OIL AND ANTIFREEZE IN THEM.OR YOUR BOLT HOLES IS STRIPPED.YOU HAVE TO REMOVE HEAD TO FIX THE THREAD PROBLEM.IF YOU HAVE NOT MADE THE FINAL TORQUE TO CRUSH AND SEAL HEAD GASKET THE. HEAD GASKET PROBABLY ALRIGHT.YOU HAVE TO LOOSEN HEAD BOLTS IN SEQUENCE BACK OFF A LITTLE AT EACH BOLTS.IF HEAD GASKET LOOK DAMAGE AT BOLT HOLES REPLACE HEAD GASKET.

Nov 13, 2009 | Toyota 4Runner Cars & Trucks

2 Answers

Stripped oil plug


If you use a good pair of vise grips you may be able to get it off if you adjust the visegripes just beyond your ability to clamp them and then proceed to clamp them shut with a large pair of channel lock pliers, if this does not work drill the appropriate size hole through the bolt and tap in a large easy out bolt extractor into the hole drilled and proceed to use a star socket
on the end of the extractor to unsrew the frozen oil pan bolt.

Jul 16, 2009 | 2001 Buick LeSabre

Not finding what you are looking for?
2008 Hyosung GT250 Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...