Question about 2004 Honda VT 750 Shadow Aero
Posted by Anonymous on
Hi, Anonymous and the usual suspects are:
1. Idle port, transfer ports, slow air jet clogged.
2. Idle adjusting screw set too low.
3. Air fuel mixture adjustment too lean.
4. Pilot/slow fuel jet clogged.
5. Faulty accelerator pump.
6. Float level too low.
7. Float bowl contaminated old fuel, water, dirt, rust, etc.
8. Carburetor bowl vent line clogged/blocked/pinched.
9. Fuel line to carburetor kinked or pinched.
10. Fuel filter clogged.
11. Intake manifold leak.
12. The gas cap is not venting properly or fuel tank venting system blocked.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
15. Multi carburetors not in sync.
16. Faulty fuel pump.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Starts choke but dies with little throttle
02 shadow spirit 750 dies if given any throttle Shadowriders
Honda 1998 VT750C Service Manual
Honda VT750C Owner Manual
Posted on Jul 20, 2017
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2004 Honda Shadow Aero stalls
There seems to be low gas level in the float chamber of the carburator.
Clean the carburator and check the float level and reset.
With the choke 'on' and if you hit the throttle it will die because there is a restriction of the air flow to the carburator.
Posted on Jul 19, 2009
check fuel level, u may need to check the flow of petrol to it,,Also if that does not solve you may need to service the carb and check fuel filter,air filter etc...
Posted on Aug 31, 2009
You do not have to remove the final drive , the wheel is resting on a spline shaft. Center stand the motorcycle or lift the rear wheel, remove the axle bolt, knock out the spacer, and slide the brake panel out of the way. Now the wheel is resting only on a splined shaft. Grab the wheel and gently slide it away from the final drive ( off the splined shaft ) and roll it out the back of the wheel well. When replacing the wheel be sure to get some MOLY60 paste from the Honda dealer and grease the spline before putting the wheel back on.
Posted on Jul 29, 2010
it takes between 3-4 quarts but that model has a dip stick on the oil cap so use it to check as you fill,also make sure to only use motorcycle oil,car oils break down to fast and were not designed for motorcycle use, honda makes a very good oil, i would use a 10w-40 for cold weather and 20w-50 for hot weather,also i would suggest a synthetic oil, it will shift easier and make those movable parts last allot longer. ( preventative maintenance )
Posted on Sep 27, 2010
Tips for a great answer:
Jul 13, 2014 | 2004 Honda VT 750 Shadow Aero
Apr 26, 2014 | 2004 Honda VT 750 Shadow Aero
Mar 22, 2014 | 2005 Honda VT 750 Shadow Aero
Oct 21, 2012 | 2004 Honda VT 750 Shadow Aero
Jul 12, 2012 | 2004 Honda VT 750 Shadow Aero
Oct 06, 2011 | 2004 Honda VT 750 Shadow Aero
Apr 29, 2011 | 2004 Honda VT 750 Shadow Aero
Mar 03, 2011 | 2004 Honda VT 750 Shadow Aero
May 27, 2009 | 2004 Honda VT 750 Shadow Aero
45 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: