Question about 2008 Husqvarna SM 125 S

Open Question

Problem z ecu 6 - 2008 Husqvarna SM 125 S

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will not start in cold weather unless you use something to heat up ecu. Can ecu be purchased preflashed


Sounds as if there is a poor solder/connection within the ECU. Most ECU's need to be installed into the vehicle when flashing is done. Check electrical connections/plugs at the ECU for looseness. Sometimes, just connecting/reconnecting the plugs may correct the problem

Feb 22, 2016 | 2003 Mazda 6

1 Answer

Ecu falt change same ecu after no start


When you change the ecu you must to rewrite the imobiliser key code or you must to buy a second hand one with imobiliser and key

Jul 13, 2014 | 2012 Ford Expedition XL 4dr SUV 5.4L V8...

2 Answers

Ecm fuse problems


Well if you've had your ECM burn and got it changed and the same thing happen again then there might be a pilled positive wire exposed to the body or the chassis of your car touching at some point,my best advice is to trace all positive heavy wires leading from the starter and under the fuse board as well.i hope this helps thanks

Jun 23, 2014 | 2003 Ford F150 Regular Cab

1 Answer

Flashing light #1 on the display of a 2004 recon es Honda atv


How many blinks on the 1st gear light? Here's the code definitions that should be for your quad.

Code 0 (no flashes) - The system is functioning normally
Code 1 (one flash) - Electronic control unit
Code 2 (two flashes) - Shift Switch or it's circuit
Code 3 (three flashes) - Angle sensor or it's circuit
Code 4 (four flashes) - Gear position switch or it's circuit
Code 5 (five flashes) - ECU motor circuit (defective ECU)
Code 6 (six flashes) - ECU failsafe relay circuit (defective ECU)
Code 7 (seven flashes) - ECU voltage converter circuit (defective ECU)
Code 8 (eight flashes) - Angle sensor, control motor, ECU or circuit
Code 9 (nine flashes) - Angle sensor, it's circuit or ECU
Code 10 (ten flashes) - Pulse generator or it's circuit
Code 11 (eleven flashes) - Speed Sensor , it's circuit or ECU
Code 12 (twelve flashes) - Gear position switch, it's circuit or ECU

I hope this helps you out.

Oct 08, 2013 | ATVs

1 Answer

R 15 missing while accelerating with Daytona ecu


Hi, Anonymous for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.daytonaindonesia.com/customer-support/ecu-software---program-download/6
Daytona Android ECU Calibration
Yamaha YZF R15A Owner Manual
OEM parts for Yamaha
Yamaha YZF R15 Service Manual

Nov 23, 2012 | 2008 Yamaha YZF-R15

1 Answer

ECU


Hello
Try these links.
www.tyresmoke.net/forum/audi.../7324-how-reset-ecu-correctly.html
www.hondaclub.com/forum/.../208-ecu-resetting-performance-6.htm...Cached
www.youtube.com/watch?v=RUhHiJgsmAg
www.nicoclub.com/.../g35-how-to-reset-ecu-throttle-pedal-release-idl...Cached - Similar
www.youtube.com/watch?v=Y1sVpHClhXs

Feb 27, 2012 | Toyota Cars & Trucks

1 Answer

I have a 1997 328 ic that has a check engine light on I bought a code reader but all it tells me is the code and the problem I don't know how to fix it the codes are 41 camshaft sensor and f-6 which is...


check for a wet ecu

the ecu compartment is under the windshield on the passenger side on E36

you gain acess to it under the hood....
this compartment gets wet, the ecu lays on a flat surface in that
compartment.

the bottom side of the circuit board gets wet and starts corrosion.

remove the ecu, take the bottom plate off, clean the bottom of the circuit
board with alcohol and a soft tooth brush.

you should be able to see the signs of corrosion or conductive build up.

this gunk bridges solder points doing all sort s of wierd things to your
car, including false sensor readings from asc/abs controllers and other
sensors....

all the way to engine failure and worst case burnt and shorted wiring
harness.

I'm on my 3rd ecu, took me and the repair boys a few years to figure this
one out.

BTW: i would get that ecu mounted above that flat surface, use some sort
of standoff to raise it so that it is not laying in the wet.

Nov 24, 2009 | 1997 BMW 328

1 Answer

Instructions for replacing 1997 Jeep Wrangler 6cyl


Its an easy job! Disconnect the battery first! That's very importand! Then disconnect the wiring pack from the ECU. Some models are equipt with snap-systems, other with a screw-system to remove the wiring connector from the ECU. If done, there are three or four screws that hold the ECU in place with the body. Remove the screws and you hold the ECU in your hands. To buy a new or rebuilt ECU, reffer to the numbers shown on the label at your Wranglers ECU in combination with the V.I.N. To connect the new ECU with the wiring pack, be careful with the connector! You need to put him in the right position to connect with the ECU. Do it slow and make sure the connector fits to all points. Otherwise you'll bake some contacts inside the connector.

Oct 23, 2009 | 1997 Jeep Wrangler

1 Answer

My 200 honda recon first gear light is blinking and engine wont stay running


How many blinks on the 1st gear light? Here's the code definitions that should be for your quad. Count the flashes and look it up here. Call your dealership or local repair shop for more info and parts if you're planning on tackling it yourself.

Code 0 (no flashes) - The system is functioning normally
Code 1 (one flash) - Electronic control unit
Code 2 (two flashes) - Shift Switch or it's circuit
Code 3 (three flashes) - Angle sensor or it's circuit
Code 4 (four flashes) - Gear position switch or it's circuit
Code 5 (five flashes) - ECU motor circuit (defective ECU)
Code 6 (six flashes) - ECU failsafe relay circuit (defective ECU)
Code 7 (seven flashes) - ECU voltage converter circuit (defective ECU)
Code 8 (eight flashes) - Angle sensor, control motor, ECU or circuit
Code 9 (nine flashes) - Angle sensor, it's circuit or ECU
Code 10 (ten flashes) - Pulse generator or it's circuit
Code 11 (eleven flashes) - Speed Sensor , it's circuit or ECU
Code 12 (twelve flashes) - Gear position switch, it's circuit or ECU

I hope this helps you out.

Jun 04, 2009 | RTO 200cc Full Size Four Wheeler ATV

Not finding what you are looking for?
2008 Husqvarna SM 125 S Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

choprboz5

Level 2 Expert

196 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...