Question about 2005 Hyosung GT 650 R

1 Answer

Rubber Hose From The Head

I have a burnt hose that comes from the head ...what is it for and can i use a fuel line or some other type of hose to replace it?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

The hose is just a breather hose. Run the new hose into the air box. Replace it with any hose that is heat proof and one that gas will not deteriorate. Any auto parts dealer or motorcycle shop should be able to supply the hose.

A “very helpful” rating for this answer? Thanks! < < And it doesn't cost anything extra!

Posted on Jun 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I need the rubber boots or vaccum lines that go from the carburator to the head or lower engine! But i do not know how to order them because i dont know what there called

Some rubber vacuum hose elbows & such, are in auto parts
stores, usually on the wall or a stand

On a carburated motor, you use EEC Vacuum Hose
(Evaporative Emission Control)---not washer hose

The larger 3/8" hose-- you use EEC or Fuel Line Hose

It doesn't have to meet fuel injected standard, but either
hose spec can be used That will be the Jxxxx numbers on the

You have no vehicle shown here,no motor & I fail to understand
hoses that go to the head or lower engine!

Apr 09, 2014 | Cars & Trucks

2 Answers

American Standard Kitchen Faucet Low water flow

I had the same issue with an American Standard faucet that I installed new 6 months ago. The diverter can be the issue if you have a sprayer attachment. Try unscrewing the sprayer head from the hose it's attached to. Now run the water full pressure with the hose pointed into the sink, obviously :~). After running the water for about 1 minute, connect the sprayer head back onto the hose, make certain the flat rubber washer and ring gaskets are seated in their grooves properly, and tighten until you have no water leaking from the sprayer head/hose connection. Now try the water through the faucet. If the problem was a temporary diverter issue, your pressure should be fine now. Good luck

Oct 31, 2011 | American Standard Kitchen Faucet 6310 020...

3 Answers

Overheated due to a heater hose leak all hoses were replaced but now have white smoke coming from tail pipe that smells of antifreeze

White smoke is burning antifreeze. You have more than likely blown a head gasket which is allowing coolant into the combustion chamber where is is being mixed with fuel and burnt.

Aug 07, 2011 | 1999 Chevrolet Suburban

1 Answer

Tried to repair a gas leak under car . we tried to repair the hose now it doesnt leak from above the hose only under and used 2 clamps and it is tight as we are able to get it is it the metal piping ?

you don`t say what type of fuel system you have,carburetor or fuel injection,throttle body or port fuel injection system.this determines the type of repair.if it is port fuel injection then you cannot repair with a hose,it must be repaired with a steel line as the fuel pressure is above 30lbs pressure and rubber hose is not strong enough for the can replace the section of line that is bad with a new steel line connected to a good section.if it`s carburetor the pressure is only about 6 to 8lbs pressure,and a hose can make the repair.if it`s throttle body then the pressure can range anywhere from 15 to about 20lbs pressure,this can be repaired with fuel injection gas hose,so you can see it makes a difference what system you have.any rubber hose used must be a fuel line hose not just any rubber hose.

Mar 15, 2011 | Chrysler New Yorker Cars & Trucks

2 Answers

I have been told that you have to replace the head bolts when replacing the head gasket because the bolts will stretch. Is this true?

If you change the head bolts that's the safest bet for trouble free operation. But, I've changed head bolts on Hondas for years and they never stretched. I know this is for a Kia. My best guess is that it's not necessary since the Chilton based manuals don't say to do this.

If the head is torqued down to specifications and it leaks, then I would say, otherwise. Even torque is more important than bolt stretch, especially if the bolts don't stretch so much that the head gasket can't be tight against the head and block.

Jan 31, 2011 | 1999 Kia Sportage

1 Answer

Black and decker VP450 battery garden sprayer. not holding pressure.

Check large rubber "O" ring under pump top and outlet hose. If that is OK then probably their is an internal leak in a hose. It can be fixed if you are handy with vacuum tube or fuel hose purchase from local auto supply house. The internal hoses are 1/4" and 3/8" or metric equivalent. The pump head comes apart by unscrewing Philips head screws and separating the housing halves. Take a photo with your digital camera before working inside unit so you will remeber how it fits back together.

Sep 07, 2010 | Garden

1 Answer



Things You'll Need:
Fuel-line disconnect tool
New gasket
New fuel pump
Flat head screwdriver
Ratchet and socket
The assistance of a friend (only when you are ready to remove the back seat)
Rubber hose plugs
Two adjustable wrenches

Locate the fuse panel under the hood of your vehicle, then open it and remove the fuel pump fuse with your hands.

Start your car and allow the fuel system to depressurize by allowing the car to idle until the engine dies.

Reinstall the fuse, then disconnect the battery with a ratchet and socket. Drain the gas from the gas tank with a siphoning kit.

Remove the back seat by unbolting the base with a ratchet and socket and lifting the seat out with your hands. The bolts are located on either side of the seat near the base. You will also need the assistance of another person to lift the seat out safely.

Remove the wiring harness by gently pulling it from the connector, and detach the rubber grommet with a flat head screwdriver. Unbolt the fuel tank cover with a ratchet and socket, remove it with your hands, pull the wires through the grommet, detach the fuel line hoses with a fuel-line disconnect tool, and lift the hoses out. Cap the hoses with rubber hose plugs.

Reach directly into the gas tank, then remove the fuel filter using two adjustable wrenches, placing one on either side of the fuel filter. You will recognize the fuel filter by its filtering paper cartridges.

Install the new filter, then follow the previous steps in reverse to complete the installation. Refill your gas take when finished

Jul 08, 2010 | 2008 Hyundai Tucson

1 Answer

Oil coming from the area where rubber hose goes

pcv cracked? The spark plugs are installed into the top of the head.
Replace cracked or dry rotted hose or the gromit for the crank case pressure valve, this should return through a line to the intake. Good luck

Aug 29, 2009 | 2003 Chrysler PT Cruiser

2 Answers

I have been looking for a repair manual for a 99

# Properly relieve the fuel system pressure.

# Drain the cooling system.

# Remove or disconnect the following:

Negative battery cable

Brake booster vacuum hose from the dynamic chamber

Fuel line from the pressure regulator and the return line from the rear of the dynamic chamber

Ground wire from the intake manifold

Purge solenoid valve vacuum hose

Upper radiator hose

Intake manifold support bracket

Converter flange inlet pipe

Timing belt

Cylinder head cover

Cylinder head with the intake and exhaust manifolds attached

3 wire harness connectors at the rear of the cylinder head


May 14, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
2005 Hyosung GT 650 R Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides