Question about 2001 kawasaki ZX-6R Ninja

1 Answer

I need a diagram of rear caliper so i can see how the metal clips fit in the caliper they go under brake pads but i dont know how (kawasaki ninja zx6r j2 model

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Suzuki VL 1500 Intruder LC REAR DISC RATTLE,HOW DO I REPLACE IT?


Hello Dale, this is an easy job on your bike. Use a flat head screw driver and remove the brake pad cover...it will pop off.
Remove the hairpin type clips off of the ends of the brake pad pins.... Use pliers & pull the brake pad pins out from the front of the rear brake caliper....Clean the rear brake caliper's piston with brake cleaner. Use a rag and wipe it clean...Reinsert the old brake pads into the caliper. Place a pry bar between the brake pads, then push the inner piston into the caliper body, this will allow room to install new pads.... Remove the old brake pads...Coat the brake pad pins and the new brake pads metal back plates with high-temperature grease.

Slip the new brake pads into the rear brake caliper, then push the brake pad pins halfway into the caliper. Slip the spring clips into place between the brake pads and the brake pad pins. Push the brake pad pins completely through the rear brake caliper. Push the hairpin clips back into the brake pad pin tips. Snap the brake pad cover onto the top of the rear brake caliper....

Pump the rear brake pedal until the pedal feels firm, indicating that the brake pads have closed around the brake rotor...No bleeding will be needed because the system was never opened - That's all there is to it...i hope this information is helpful & good luck with your bike.


11_23_2011_12_23_40_am.jpg

Nov 22, 2011 | 2003 Suzuki VL 1500 Intruder LC

1 Answer

Change rear brakes


Just follow this instructions:

1 Unbolt the brake caliper from the front fork or rear swingarm, using a socket wrench. Use a 14-mm hex socket to unscrew the front caliper bolts, and a 6-mm Allen socket for the rear caliper.
2 Slide the caliper off the brake rotor. Suspend the caliper from the handlebars or frame, if needed, using a bungee cord.
3 Pull the hair clip pin out of the brake pad's retaining pin on the outside face of the caliper using a pair of needle-nose pliers. Push the retaining pin out of the back of the caliper with your finger.
4 Pull the brake pads and their spring clip out of the caliper. Retain the spring clip, and discard the brake pads.
5 Reinstall the brake calipers, following the reverse method of removal.

I hope this will help you. thanks

Sep 22, 2011 | 1998 kawasaki ZX-6R Ninja

1 Answer

There are 2 clips on the lower portion of the front brake caliper.. does anyone have a diagram of the caliper layout from a factory manual for a 2004 rmz 250. i need to figure out how each clip locks...


I believe you mean the clips that keep the brake pads from rattling.
The smaller one of the two, fits into the caliper where the front of the pads slide into the caliper. It goes between the pads and caliper, and has a slot to where the disc fits. It kinda fits into a recessed rectangle hole. (Opposite the brake pad pin.)
The longer clip has two small tabs on it's back, near the center, that clips towards the top center of the caliper, and it puts pressure downward on the pads. One end rests on the top of the pads, as the other ends up resting on the "pin" that holds the pads in place.
Look close, and you should see marks where they were, as they can only go on one correct way.
Good luck!

Oct 08, 2010 | 2004 Suzuki RM 250

1 Answer

What brake pads etc and disks do i need for my bike. ZX6R Ninja (1996) (P).


These are the part numbers from Kawasaki

Front brake pads, you will need 2 sets 43082-1142

The front rotors have been canceled, I will give you the part number 41080-1398-5C

Rear brake pads 43082-1171

The rear rear is also canceled part number 41080-1389-FB

Apr 29, 2010 | 1996 kawasaki ZX-6R Ninja

1 Answer

Do you have to take off rear wheel to do the rear brakes if not how do you do it??


hi,if you are only replacing the pads then there is no need to take the wheel off,simply undo the two bolts holding the caliper to the carrier,remove the caliper from the disc,push the brake pads back (with a screwdriver or something similar),flip the caliper over,remove the plastic cover(if fitted),remove the"r"clips that hold the brake pins in(some models have external bolts and cut plates or tabs but they all do the same job of holding the brake pins in),once you have the clips out,the pins will slide out and the pads will be able to be removed,replace the pads and reassemble opposite to removal,easy job should take about 20 mins from start to finish.dont forget ,once you have the caliper back on to pump the brake lever a few times untill the pads seat against the disc and you have full brake pressure again..hope this helps...cheers

Apr 01, 2010 | 1999 Suzuki GSX-R 750 X

1 Answer

Right side rear brake drags


Remove all rust from pad and caliper sliding surfaces,eg metal to metal,not the pins,they get synthetic brake lube. Apply anti-seize to all sliding surfaces. Make sure you can screw in the rear caliper piston,if applicable, and manually ratchet up the parking brake,after caliper and pads are on. Bleed/Flush all 4 Wheels. Make sure you can slide the pads back and forth,before lubing end tabs. You may need to file a little off the ends or just remove the paint. Make sure parking brake cables are really releasing.

Mar 12, 2010 | 2001 Mitsubishi Montero Sport 4WD

2 Answers

How to fit rear brake pad retainer clip when i took the rear brake pads out the pad retainer clip fell out and i cannot see how the little clip fits back on


If the clip has a slot in it then it fits in the caliper where the ends of the pads fit.
If not & it has a sprung tab then it fits in the caliper where the top of the pads fit

Hope this helps.
(If it does then please mark this as 'useful')
Ride Safe
Bike-Doc

Jan 29, 2010 | 2000 kawasaki ZX-9 R Ninja

1 Answer

Brake rotors need to be resurfaced,explain best way to remove rotors from vehicle.


front ones remove wire clip remove bolts from caliper hang caliper out of way remove pads remove 2 bolts from pad carrier put to one side remove 2 disc retaining bolts remove disc may need hammer clean hub flange with wire brush fit new disc clean pad carrier and refit fit new pads put some copper grease on back of pads push in caliper piston slowly using large grips or g clamp fit and secure caliper pump up brake pedal check brake fluid level do other side for rear brakes see my solutions

Dec 01, 2009 | 1999 Volvo S80

1 Answer

Rear brake caliper clip


its probably the anti rattle plate that fits onto the pad itself!

Jul 27, 2009 | 2007 kawasaki ZX-10R SE

2 Answers

NEED TO REMOVE REAR ROTOR


Take off the wheel, remove the brake caliper (2 bolts on the back), then the rotor just slides off, the wheel studs are part of the hub assembly not the rotor.

Nov 21, 2008 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
2001 kawasaki ZX-6R Ninja Logo

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...