Question about 2006 Harley Davidson FXDI Dyna Super Glide

1 Answer

2006 harley clutch pack assembly - 2006 Harley Davidson FXDI Dyna Super Glide

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

After having soaked the friction plates as required first install the narrow friction plate on the clutch hub, engaging the tabs on this plate with the slots in the clutch shell then install the damper spring seat (sometimes called a judder spring) on the clutch hub so that it sits inboard of the previously installed narrow friction plate with the concave side out (facing away from damper spring
seat) (that will be with the narrow side facing into the clutch hub and the wider side facing out) THEN install a steel plate with the round edge (produced when the plate was stamped out from a larger piece of steel) outward and then install a regular friction plate onto the clutch hub and continue by installing the seven remaining sets of steel and fibre plates in the same manner, alternating between steel plates and friction plates so that no two steel are touching each other and so that no two fibre plates are touching each other and then when they are all in place install the pressure plate onto the clutch hub aligning holes in the plate with the threaded bosses on the hub. THEN install and seat the diaphragm spring into the recess of the pressure plate with the concave side inward and with the holes in the diaphragm spring retainer aligned with the threaded bosses on the clutch hub tabs on the spring retainer contact flats on the inboard side of the bosses install the six metric bolts to secure the diaphragm spring retainer to the clutch hub and alternately tighten the bolts to 90-110 in-lbs (10.2-12.4 Nm).

Posted on Oct 18, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 FXDBI makes a noise when it in neutral, but when I put it in gear the noise stops?


That's where the clutch pack is. As long as the clutch is working ok, don't worry about it. They all make noise.

Jun 17, 2014 | 2006 Harley Davidson FXDBI Street Bob

2 Answers

This thing suxs


Right about 1 quart (give or take about and fluid ounce or two).

Two ways to judge:

1: hold bike upright, remove derby cover (over clutch pack).
Pour primary fluid through derby cover hole until level comes up to just the bottom of the clutch plates.

------------------------OR-------------------

2: With bike on kick stand, pour fluid through derby cover opening until level is just below the derby cover opening.

Apr 17, 2014 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Removing a clutch pack on a 1996 electra glide


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Stator Repair 3b of 9 Clutch Assembly Removal Tool Listing

Apr 25, 2012 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

I am switching from a barnet back to the stock clutch on my 06 sportster 1200. How do I assemble the plates?


http://www.bikebandit.com/2006-harley-davidson-sportster-1200-low-xl1200l/o/m18603#sch622966

You assemble the clutch plates alternating with fiber to metal. The "spring plate" goes in the middle of the clutch pac. Refer to the draw at the above site. I hope this helps.

Good Luck
Steve

Sep 12, 2011 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

How would you install a clutch on a 2007 xl 1200 harley davidson


If you are going to replace the entire clutch assembly, simply remove engine sprocket, primary chain, and the mainshaft nut, pull the clutch assembly off and put another one on. But, this is extremely expensive because you're replacing the inner clutch hub and the outer clutch shell. If you want to simply put new clutch discs in, you need a special tool to compress the diaphragm type clutch spring and get the snap ring off. The tool cost about $50 or so depending on the brand of tool you purchase.

http://www.ironeagle.com/product_info.php?products_id=5252

Barnett clutch tool for Sportsters, Custom Chrome number 14966

Good Luck
Steve

Sep 04, 2011 | 2006 Harley Davidson XL 1200 C Sportster...

2 Answers

Disassemble the clutch so I can install new primary chain


Isn't there a big nut in the middle of the clutch pack? Also I am not sure, it might be a left-handed one, check the threads first.

May 12, 2010 | 1993 Harley Davidson FXR Super Glide

Not finding what you are looking for?
2006 Harley Davidson FXDI Dyna Super Glide Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...