Question about 2005 Harley Davidson FLHT - FLHTI Electra Glide Standard

1 Answer

Clutch takes too early - 2005 Harley Davidson FLHT - FLHTI Electra Glide Standard

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

Adjust it

Posted on Oct 18, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My clutch. 2014 escape smells like burning brakes why

Could be your emergency break is locked on. Could be reason for early clutch failure. Other wise if you are sure it is the clutch, it has not been adjusted properly and so slipping. Take it back to installer. I had a standard 5spd never changed clutch in 175,000 miles. Or you are keeping your foot on the clutch. Learn to drive with minimum clutch effort.

Feb 27, 2015 | 2014 Ford Escape

1 Answer

Where is serial number located on early 440 a skidder

Probably it is on a plate on the right side of the clutch housing, just behind the engine. You need to take the side panel off to see it.

Feb 08, 2015 | Caterpillar Skid Stear Loader

1 Answer

My clutch is loose, i can not change gears

To have better performance change your clutch. Please take early steps else some expensive parts may also be damaged. Here you can get all necessary Hyundai car parts

May 20, 2011 | 2000 Hyundai Accent

1 Answer

Please can someone tell me how to take off the drive pulley assy on a husqvarna k750 partner and fit the new one. thanks Ian

To remove the drive pulley from the engine you need to remove the clutch, there is a 19mm nut on the outside of the clutch, if you have an impact gun, fit a 19mm socket and jar the clutch off against compression ( left hand thread, turn clockwise as you look at it ) if you do not have an impact gun then you will have to use a suitable 19mm socket and speed brace, keep tapping the brace clockwise with a soft hammer until the clutch spins off. There are two different pulleys, the early pulley has a open needle bearing, the later pulley has a fully sealed bearing, they are not inter changeble.
Hope this answers your question

Feb 05, 2011 | Garden

1 Answer

I have noise at the clutch and when i press the clutch pedal the noise go off

Did you check you clutch fluid level? It may be low. Also chattering is usally an early sign that the pressure plate/clutch is starting to wear out.

Feb 04, 2011 | Kia Sportage Cars & Trucks

1 Answer

How to remove the clutch fan on a 2004 dodge ram

autozone usually has a fan clutch loaner tool set, however in a pinch a strap wrench can hold the pulley and then you have room to fit a decent size crescent wrench. In a hurry you can use an air hammer on an edge (of the nut) going counterclockwise, they also make a neat tool that does basically the same thing, might take a few tries but you will get it.

Jul 27, 2010 | 2004 Dodge Ram 2500

1 Answer

Adjust the clutch

If I'm not mistaken, in the early 90's the auto manufacturers started going to a hydraulic clutch. Unfortunately, those type of clutches are not adjustable. You will probably need to at least rebuild, if not, replace the clutch.

Jun 15, 2010 | 1994 Ford Escort

1 Answer

How to adjust your clutch in 1990 4runner

the 4runner uses a hydraulic clutch only the older mechanical linkage type clutch release systems were adjustable, thiose went out in the early 80's, this type of clutch release is self adjusting, if the clutch is slipping then it is worn out.

Jun 04, 2010 | Toyota 4Runner Cars & Trucks

1 Answer

Seems to slip on take off

early signs of wear on clutch drive / pressure plate.....take off slowly and it may last a couple of thousand kilometers

Jul 24, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
2005 Harley Davidson FLHT - FLHTI Electra Glide Standard Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4999 Answers


Level 3 Expert

4350 Answers


Level 3 Expert

80668 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides