Question about Motorcycles

1 Answer

Jet pump wont run on hot springs classic 110 volt the light lights up when attempting to activate the timed jets

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 665 Answers

And, what does this question have to do with motorcycles?

Posted on Apr 17, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hot tub has an issue. Only half the display is working, there's no heat and the jets wont turn on. If I trip the curcit, I can get the hot tub jets for 10-30 seconds and that's it. HELp


Almost all hot tubs use 230 volt AC power which comes from the power company in two power wires plus one common common wire. You get common 115 volts between a common and either other wire. "Half way" working could well be an attempt to run on only one of the wires. There is also likely to be a ground fault circuit breaker in the wiring which makes sure current going out to the tub is all returned via the wires and not through someone's legs to ground. If you're comfortable with an AC voltmeter check some voltages but understand that 230 volts is way into the killing range. Two people present and well insulated probes are important.

Apr 15, 2016 | Pool & Spa

2 Answers

Why wont hot tub heat with jets on losing temperature on 110 volt


My first question would be about the outside temperature. What is the outside temperature?
Hot tubs that are designed to operate on 115v only have 1.5kw heaters and if the outside temperature is below 50 deg F they tend to not keep up to 103 deg water while being used. They are also designed to not heat while the high speed pump is operating.
Does it stay up to temperature on a normal basis?

ROD
US Parts Center

Jun 08, 2014 | Qca Spas Dream Series Dream Master Hot Tub...

1 Answer

Balboa VL700S control panel jets 1 not working


Your problem is going to be in the circuit board in the spa control box under the skirt.
You have a bad relay.
Rod
US Parts Center

Jun 25, 2013 | Pool & Spa

1 Answer

Factory Jet Sizes


Front cylinder carburetor:

·
112.5 Main Jet

·
17.5 Pilot Jet

·
(1) 0.020" thick shim washer under the needle

·
PMS setting apparently varies from bike to bike... but it should be 2.5 turns

Rear cylinder carburetor:

·
110 Main Jet

·
17.5 Pilot Jet

·
(1) 0.020" thick shim washer under the needle

·
PMS setting apparently varies from bike to bike... but it should be 2.5 turns

May 23, 2013 | 2000 Yamaha V Star 1100 Classic

1 Answer

Idle adj screw vibrates out and the idle speed is high.


Hi Charles Gregory.

When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.
Make sure your spring that goes on the idle screw is in place.
You can also use some "locktite" thread locking compound on the threads of the needle if the spring is missing.
Normally you will adjust your idle jet to 1/2-3/4 turn open from the bottom seated position.
Then you will re-adjust the low speed of the engine when the engine is warm by turning the idle screw in or out till the engine runs smoothly at idle speed, around 1200 RPM.
The high speed jet is adjusted to 1 1/2- 1 3/4 open from the bottom seated position, after the engine is warm.
Then re-adjusted by turning the High Speed jet adjustment screw in or out till the motor runs smoothly at high speed.
Alway use the "lightly seated" method if you have not changed the screw settings.
Please take time to rate me
Bud

Oct 01, 2012 | Garden

2 Answers

Hot Spring Spa pump won't run just click on circuit board....


Check for voltage at the pump, before assuming the relays are out... then check for voltage before and after the relay contacts

Apr 08, 2010 | Pool & Spa

1 Answer

I have a 2000 Sovereign Hot Spring hot tub that quite heating, I checked filters they are ok, I have no air lock, The jets and light work fine. Inside the control box on the circuit board all 3 led lights...


Check for a bad heater controller board or burnt wire connection going to the heater. You can check for voltage across the white and black leads going to the heater from the heater controller board (upper left corner of the black control box

Mar 31, 2010 | Waterway 5 Hp 230 Volt 2 Speed Side...

2 Answers

Jet pump will not shutt off after I replaced heater relay. Tub is a hot springs landmark with an IQ2000 panel the year is also a 2000


it sounds like the pump relay may be stuck closed. Also check the temp readout, if it thinks the water is too hot it will try to cool the water by running the jets and sometimes the blower as well.

Dec 08, 2009 | RTO 2 Person Spa Hot Tub 8 Hydrotherapy...

1 Answer

"high pump" (jets) shutoff


look at circit board see if it s burnt replace

Sep 30, 2008 | Waterway 1 Hp 115 Volt 2 Speed Side...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...