Question about 2006 Harley Davidson FXDBI Street Bob

1 Answer

2006 Harley Street Bob stalls - 2006 Harley Davidson FXDBI Street Bob

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

Under what conditions????

What DTCs are set????????????

Possibly IAC, is p0505 set???

Posted on Oct 18, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2006 Harley Street Glide turn signal problems

hi, if you have not yet fixed the problem , the fuse box is located underneath the left sidecover in front of the left sattlebag youll need to remove the bag to get the side cover off ck the fuses thats all it should be ,prolly what happened was a bulb went bad and shorted the circut blowing the fuse for them theyre on the same fuse as the tach and speedo

Posted on Apr 27, 2009

jigsaw_9077
  • 308 Answers

SOURCE: Speedometer stopped working and mileage is not

check the wires connected to the speedometer .if the speedometer is not working replace speedometer.

Posted on Jul 10, 2009

  • 47 Answers

SOURCE: Replacement of a stock fuel gauge on a '06 Harley Street Bob.

no need to remove tank, Remove terminal pins from connector under left side of tank then pull gauge and wires out. Install new gauge, replace terminal pins in their propper place in the connector,plug it in and varify the repair.

Posted on Dec 22, 2009

wd4ity
  • 4565 Answers

SOURCE: Changing grips. Any suggestions or warnings,

Usually when you change the grips on the throttle side, depending on what type of replacement grips you bought, you'll be replacing the throttle sleeve as well. This means that you will be messing with the throttle and idle cables.

Loosen both cables at the adjusters as loose as they will go. Then, remove the two bolts that hold the right hand switch housing together. Carefully seperate the two halves. Do not damage the wires going to the switch. Work the throttle cable and the idle cable out of there slots in the throttle sleeve of the old grip. Be careful not to loose the brass ferrel that goes over the cable end. Lubricate the inside of the new throttle sleeve, the handlebar, and the area where the cables hook up with white lithium grease. Reassemble cables into new sleeve and reassemble the switch housing.

Once you have everything back together, adjust the throttle cable first and leave just a bit of slack in the cable. You should be able to freely "rock the throttle grip" before you feel the cable tighten up, Just a bit. Then adjust the idle cable about the same way.

Now, Turn the throttle cable to Wide Open throttle position and release it. It should "snap" shut, do this again from half and quarter throttle to make sure it works as it should. Failure to insure that the throttle operates properly can cause serious injury or death.

If you are simply replacing a grip on each side of the handlebar, use a long slender blade screwdriver or an ice pick to slide between the handlebar and the grip. Spray some WD40 in the work the grip a bit and it will break loose. Clean the throttle sleeve and handlebar off alcohol. Now, some people like to use "Grip Glue" on the new grips. Put the glue inside the grip and slide it up on the handlebar. If you put the glue on the handlebar, it will roll up in front of the grip as you slide it on to the handlebar or throttle sleeve. Make sure you "align" the two grips so they look the same before the glue sets.

Good Luck
Steve

Posted on Jul 18, 2010

wd4ity
  • 4565 Answers

SOURCE: 2006 Harley Davidson street glide brake light

Try loosening the bolts holding the front master cylinder on the handlebars. Slide the master cylinder down as close as possible to the right handlebar switch housing. If this doesn't work, the front brake light switch is probably bad and needs to be replaced in the right switch housing.

Good luck
Steve

Posted on Sep 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Harley stalls on idle


Could be the IAC Is code P0505 set. What other codes ares set, if any???

May 04, 2014 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Replace battery 2006 street bob


Hi Kirdape, for more information on your question please visit the websites below and good luck:
How to remove battery cover from Harley Davidson how to remove battery Dyna

Mar 28, 2012 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Pics on drain plug on 2006 harley davidson dtreet bob


Hi Anonymous, for more information on your question please visit the websites below and good luck:
DIY Oil Change on 2003 Harley Davidson Dyna

Mar 20, 2012 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Where is the oil drain plug on the 2006 harley davidson street bob


Hi Hd_meyers, for more information on your question please visit the websites below and good luck:
DIY Oil Change on 2003 Harley Davidson Dyna

Jun 20, 2011 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

What size battery do i buy for a 2006 harley fxdbi (street bob)


Should be a YTX20HLBS. Check Yuasa batteries on there Web site.

Feb 09, 2011 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Install fuel pump 2006 harley street bob


Hi Tellison2, I'm sorry you can't find the very first and best tool you ever bought for your Harley Davidson. Despair not, for a mere $6.50 you may be able to download another one from the website below and good luck. Harley Davidson Manuals Mark Workshop
Pt 1 of 1 Replace Fuel Filter 2006 Harley Dyna Wide Glide

Aug 22, 2010 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

FIX SPEEDO ON A 2006 STREET BOB HARLEY DAVIDSON IT WORKS SOMETIMES AND SOMETIMES IT DONT


Hi,
Check the speedo pickup on the rear of the gearbox,they are magnetic,attract any debris and do not recognise the the gear passing below it.

May 08, 2010 | 2006 Harley Davidson FXDBI Street Bob

Not finding what you are looking for?
2006 Harley Davidson FXDBI Street Bob Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...