Question about Honda XR 125 L Motorcycles

1 Answer

My honda dylan se125 shredding drive belt

My honda dylan se125 keeps shredding it drive belt and it's rollers are coming out of place the garage have looed at it , but can't find anythink wrong . any help would be great thank you

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 80 Answers

Does the garage know ANYTHING about bikes? I would suggest you check the bearings, as well as the wheel alignment, the wheel should be exactly in line with the frame. Also, try to see if the spacers at either end of the wheel is in the correct place, it could be that the wheel is slightly off-centre, causing the belt to scuff against the side of the "sprocket"

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a whirlpool gas dryer. One of the drum rollers keep getting shredded and breaking only after a couple of hours of use. I have now replaced both drum rollers 5 times in the last 6 weeks.


Did you lube the bearing surfaces of the new rollers with a good lube? Is the shaft surface for the bearing smooth? Do the new rollers wobble on the shaft (very bad)? Do your have the drum on straight and is it riding on the felt surface in front ok? Do the rollers turn easily after you install them or are they jammed up for some reason? What does the surface on the drum where the rollers ride look like? Does the idler pulley for the belt hold the belt steady in the correct place on the drum or does it wobble around? I have serviced these rollers on many occasions and they last a long time. The felt in front should be both in front of the drum and reach across the outer front edge of the drum. Sometimes it get all bunched up at one spot in front of the drum without wrapping around the outside too. I put the bottom in first and then use a J shaped piece of bent tin to guide it in on top where I can't see it.

Dec 12, 2015 | Whirlpool Dryers

1 Answer

Hi I've got a honda dylan ses 125 scooter now it won't start it made to big bangs out of the exhaust whist starting the bike then just started to dye down to a ticking noise there a brand new battery


2003 Honda Dylan SES 125 Scooter Engine ebay - YouTube

? 0:47
https://www.youtube.com/watch?v=DzAByfS2OAY
Nov 21, 2012 - Uploaded by TheShamefulsin
Short video demonstrating a 2003 honda dylans engine, that it starts and runs for the purpose of selling the ..

honda dylan in United Kingdom ' Motorbikes & Scooters for ...

https://www.gumtree.com/motorbikes-scooters/uk/honda+dylan

GumtreeMy 2003 Honda Dylan ses 125, unfortunately it was stolen from me, hence the .... uk plate GF07 XJK,bike has only few scratches, last time I could not start it, but ...

Nov 29, 2015 | Honda Motorcycles

2 Answers

When i change my drive belt it gets shreded on start up


Sounds like either the belt is not tight or more likely your door balance is heavy ie fatigued/broken springs or its hung up somewhere.

Apr 16, 2014 | Chamberlain 1/2-HP Whisper Drive Belt...

1 Answer

The drive belt on my Honda HRT broke. I replaced it and within a few seconds the new belt broke. I know the blades are turning, but I'm wondering if the wheel on the transmission is not turning thus the...


could be rear end is locked up you will have to get another belt try turning wheels by hand if loose see if there are broken bearings anywhere on the drive usally thats the case with the belt bearing goes out and shreds thr belt try those ideals

Jul 30, 2013 | Garden

1 Answer

Pathmaster 8.0 treamill model 21-3688a fix


Drive Belt Installation for Treadmills

The drive belt is used by the motor to drive the treadmill walking belt via the front roller pulley. A drive pulley is mounted on the roller and the roller has knurling or a sleeve to help it drive the walking belt. The treadmill console detects the current speed of the treadmill by monitoring the movement of a magnet mounted on the front roller pulley with a reed switch or by using an optic switch which monitors an optic disk mounted either on the front roller or on the motor shaft. If the sleeve moves to the side, you will not be able to keep the belt centered and many optic disks can be warped if pushed to the side by the sleeve if it moves, but we do have replacement sleeve kits if needed.


Steps to Replace Drive Belt-

1) Remove the safety key and unplug the treadmill from the wall outlet.

2) Remove the screws securing the motor hood and gently remove the motor hood.

3) Using an Allen wrench provided with the treadmill, loosen the two rear roller adjustment bolts until the rear roller comes into contact with the walking board. Turn the bolts and equal number of turns on each side and keep a count of how many turns you made so you will know how to properly re-tension the walking belt.

4) Remove the drive belt from the motor pulley. Place a screwdriver between the pulley and the belt and turn the pulley by hand. Use the screwdriver to guide the belt over the edge of the pulley. Be careful with the screwdriver to prevent damage to the pulley.

6) Mark the position of the front roller axle on the front roller bracket above the front roller adjustment bolt using a Sharpie marker so you will know where to put the bolt back into position. Remove the front roller adjustment bolt if your treadmill's front roller has a pitch adjustment bolt. If your treadmill does not have exposed roller bolts you will need additional instructions. Please see the troubleshooting section on our website for further help.

7) Gently slide the front roller from out of its mounting position on the frame. Do NOT remove the roller from the walking belt.

8) Slip the old drive belt off the roller and loop the new drive belt onto the front roller pulley.

9) Replace the roller back into its slot on the pulley side and re-tension the front roller pitch bolt to its proper place using the Sharpie mark as a guide.

10) Using the screwdriver, loop the drive belt over the motor pulley. Many Icon units originally had the drive belt misaligned by design (if you can believe it). This was to use the side load of the drive belt in order to keep tension lower. It does lower amp draw for the machine and replacing a side load drive belt occasionally is much cheaper than replacing a motor and/or controller so if your original drive belt was off-centered, install the new belt in the same manner.

11) Re-tension the walking belt.

12) Plug in the machine and check the drive belt for slipping. You can use some automotive fan belt dressing on the grooved or contact side of the belt to help it with grip on the pulleys and it will treat the belt as well. We prefer using belt dressing rather than over-tensioning the belt for the aforementioned amp reasons as well as additional stress placed on the drive system parts.

13) Replace the motor cover and test.

14) Make sure the walking belt is not slipping and is properly aligned and your treadmill is ready to use.

Copyright 2009 by TreadmillDoctor.com, Inc.

All illustrations, photographs, and scanned images, and text are the property of TreadmillDoctor.com, Inc. and may not be reused, retransmitted, copied, given, sold, or bartered to any third party. The recipient of this property is authorized to use it only in the manner expressly indicated by a staff member of TreadmillDoctor.com, Inc. All rights reserved.

Jul 09, 2012 | Exercise & Fitness

1 Answer

My son has a Peugeot Trekker 50 2004 model. He took it out on his CBT an broke down. The drive belt was shredded - what could cause this to happen


the rollers/springs have gone mis shaped and are not engaging the clutch properly so the belt gets caught up if you have a compressor and an air gun you can changed them they only cost about £5 for a set if you dont them and garage should change them for you


hope this helps


John

Jun 30, 2011 | Peugeot RR 50 Enduro Racing Motorcycles

1 Answer

Serpentine belt keeps shredding on the inside


PULLEY ALIGNMENT.WITH BELT ON LOOK AT THE PULLEYS FROM THE SIDE.U MUST HAVE A PULLEY THE IS MISSALIGNED

May 06, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

1996 buick regal custom's belt keeps shredding


The first thing i would do is try playing with the belt tensioner. it sounds like the belt is lose and when the engine warms up the belt starts to expand and slips off.

Aug 14, 2008 | 1996 Buick Regal Olympic Gold

3 Answers

Chamberlain Whisper Belt Drive


door does not close without holding wall button in

Oct 15, 2007 | Chamberlain Powerdrive PD422D 1/2 HP...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

539 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...