Question about Suzuki VL 1500 Intruder LC Motorcycles
Speed sensor location
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hi ...... Find where the battery is, under the seat or behind a side panel. Disconnect the black (negative lead usually with a 10mm spanner then disconect the red (positive) lead. The battery will be held in place with a 'rubber' strap or a bracket and depending on type of battery there may be a vent hose from the battery to the lower half of the bike, this just pulls off and remains in place until you replace the battery. Installation is reverse except you connect red (positive) first.
Let us know how you get on.
Posted on Jan 20, 2009
Could be a bad starter push button,poor connection in wiring, bad safety switch.Need to track down with voltmeter if you can.
A good dealer may offer some help if you buy the parts needed from them.
Posted on Oct 24, 2009
You need to buy a volt meter and set it on 10, or 20 v-. Start the bike and see what it says. A good charging system will show 13-14+ volts. If the meter says 11-12 volts or does not change, you have a bad stator, or rect/reg. Take to a shop to have it further tested. Chaz Moto DC
Posted on Jan 22, 2010
Hello Dale, this is an easy job on your bike. Use a flat head screw driver and remove the brake pad cover...it will pop off.
Remove the hairpin type clips off of the ends of the brake pad pins.... Use pliers & pull the brake pad pins out from the front of the rear brake caliper....Clean the rear brake caliper's piston with brake cleaner. Use a rag and wipe it clean...Reinsert the old brake pads into the caliper. Place a pry bar between the brake pads, then push the inner piston into the caliper body, this will allow room to install new pads.... Remove the old brake pads...Coat the brake pad pins and the new brake pads metal back plates with high-temperature grease.
Slip the new brake pads into the rear brake caliper, then push the brake pad pins halfway into the caliper. Slip the spring clips into place between the brake pads and the brake pad pins. Push the brake pad pins completely through the rear brake caliper. Push the hairpin clips back into the brake pad pin tips. Snap the brake pad cover onto the top of the rear brake caliper....
Pump the rear brake pedal until the pedal feels firm, indicating that the brake pads have closed around the brake rotor...No bleeding will be needed because the system was never opened - That's all there is to it...i hope this information is helpful & good luck with your bike.
Posted on Nov 23, 2011
Tips for a great answer:
Oct 16, 2017 | 2001 Suzuki VL 1500 Intruder LC
Jul 04, 2017 | 1999 Suzuki VS 1400 Intruder
May 15, 2017 | 2001 Suzuki VL 1500 Intruder LC
Apr 21, 2017 | 1999 Suzuki VS 1400 Intruder
Apr 14, 2016 | 2002 Suzuki VL 1500 Intruder LC
Apr 02, 2016 | Suzuki Motorcycles
Jun 23, 2014 | 2000 Suzuki VL 1500 Intruder LC
Jun 04, 2011 | 2000 Suzuki VL 1500 Intruder LC
Oct 31, 2010 | 2000 Suzuki VL 1500 Intruder LC
Apr 04, 2009 | 2002 Suzuki VL 1500 Intruder LC
Jun 07, 2015 | Suzuki VL 125 Intruder LC Motorcycles
28 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: