Hub assembly diagram

There are several different varieties of rear coaster brake hubs. The most common is a "Shimano". The easiest way to tell you how to reassemble is by referring you to either Utube, put "shimano coaster brake in search box or go to SheltonBrown.com. Again enter the shimano in the search.

IF you have a axle flange that is bolted to the hub by say 6 nuts then undo the nuts and you will see small tapers around the bolts. To loosen these give the centre of the axle flange a good hard hit with a hammer. This will pop the tapers loose and allow you to get them out . Pull the axle out and you will find 4 nuts with a lock tab washer between them. If you have have discs you will need to remove the caliper first then pull the hub off.

• Air Suspension
• Front Suspension
• Rear Suspension
• • Coil Spring Rear Suspension
  • Coil Springs
  • Lower Ball Joint
  • Lower Control Arms
  • Shock Absorbers
  • Stabilizer Bar Sway Bar
  • Strut Macpherson Strut Assembly
  • Upper Control Arms
  • Wheel Bearings
• Specifications
• Wheel Alignment

• HOME
• REPAIR INFO
• 1999 LEXUS ES300 3.0L SFI DOHC 6CYL REPAIR GUIDE
• SUSPENSION
• REAR SUSPENSION
• COIL SPRING REAR SUSPENSION

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

• HUB & BEARINGS
• STABILIZER BAR
• STRUT & COIL SPRING

Print

Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Raise and safely support the vehicle.
3. Remove or disconnect the following:
   
   Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly
   

To install:

1. Install or connect the following:
   
   Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
   
2. Adjust the parking brake.
3. Stabilize the suspension as follows :
   1. Install the wheel(s).
   2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
   3. Raise the vehicle.
   4. Remove the wheel.
   5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.
   
   
4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).
   
   Rear tire and wheel assembly
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Raise and safely support the vehicle.
3. Remove or disconnect the following:
   NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.
   
   
   Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring
   

To install:

1. Install or connect the following:
   
   Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel
   

1. Before servicing the vehicle, refer to the Precautions section.
2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
3. Remove or disconnect the following:
   
   Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
   
4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
5. Remove or disconnect the following:
   
   Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
   
6. Place matchmarks on the adjusting cam and body.
7. Remove or disconnect the following:
   
   Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
   
8. Secure the axle carrier in a vise.
9. Remove or disconnect the following:
   
   Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal
   
   

   Fig. Removing the oil seal (inner)-LS 430
   
   

10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
11. Remove or disconnect the following:
    
    Axle hub
    
    

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub
    
    

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle
    
    

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing
    

To install:

1. Install or connect the following:
   
   New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.
   
   

   Fig. Installing the oil seal (outer)-LS 430
   Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.
   
   

   Fig. Installing the oil seal (inner)-LS 430
   New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable
   

2. Lower the vehicle and turn ON the air suspension switch.

Fig. Exploded view rear carrier assembly, hub and bearing-

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   WARNING Be careful not to damage the boot and ABS sensor
   
   
   Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier
   
   
   Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly
   

To install:

1. Install or connect the following:
   
   4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
   
2. Inspect and adjust rear wheel alignment
3. Check ABS speed sensor signal

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
   
3. Press the hub out of the wheel bearing, then remove the backing plate.
4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.

1. Installation is the reverse of the removal procedure, while using the following torque values:
   
   Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)
   

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor
   

To install:

1. Install or connect the following:
   NOTE Inspect bearing back lash and hub deviation
   
   
   Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire
   
   
   Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
   
2. inspect and adjust rear wheel alignment
3. Check ABS speed sensor signal

Stabilizer Bar

Removal & Installation

1. Remove the rear wheels.
2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
4. Remove the stabilizer bar.

To install:

1. Install the stabilizer bar.
2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
4. Install the rear wheels.
5. Inspect and adjust rear wheel alignment.

Strut & Coil Spring

Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.
   
   
   No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
   
3. Secure the strut in a vise.
4. Compress the coil spring
5. Remove or disconnect the following:
   
   Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

Your hub is a complete unit including wheel flange and bearing. Thje axle passes through the assembly. You will find three twelve point 13mm bolts that go into the rear of the hub through the steering knuckle.
To remove the assembly, Loosen those three bolts, run them out part way and use a socket you don't want (you will destroy it) Put the socket on each bolt and use a heavy hammer to drive the assembly out of the knuckle. Alternate sides so it does not bind. use lots of solvent on the hub parting surface.
One tip: Disconnect the tie rod end so the assembly is easy to turn from side to side.
The hub assembly is only rebuildable in a factory. It is replaced as a unit. While you have it apart, always check the axle universal for binding or play. If you remove the axle for any reason, when putting it back in don't drag it on the bottom of the tube, The seal is inside the tube next to the gear set. Dragging the axle will knock the seal out.

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical)

1. Release parking brake.
2. Remove rear wheel assembly.
3. Remove rear wheel speed sensor from carrier.
4. Dismount brake caliper and support with mechanic's wire.
5. Remove brake disc.
6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical)
   
   
7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
8. Remove carrier.
9. Remove stakes and remove flange nut.
10. Support bearing outer race flange and press rear axle hub out.
11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.

To Install:
Hub bearing assembly (Typical)

1. Apply thin coat of grease to bearing contact surface and hub.
2. Using and appropriate tool, press bearing into hub. CAUTION
   Do not press against outer race of wheel bearing.
   
3. Install flange nut and stake nut until it meets concave portion of spindle.
4. Install carrier.
5. Use an appropriate tool to press tone wheel.
6. Install hub/bearing assembly with rounded portion of outer race facing up.
7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
8. Measure wheel bearing starting torque with a spring balance or equivalent device.
   • Starting torque should measure 15.9 in lb (1.8 Nm) or less
9. Install brake disc.
10. Mount brake caliper.
11. Install rear wheel speed sensor to carrier.
12. Install rear wheel assembly.

The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal

1. Raise and support the vehicle.
   

1. Remove the wheel and tire assembly.
   

1. Remove the hub grease cap (1131) from the wheel hub.
   

1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
   

1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
   

1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
   
2. Remove the wheel hub from the rear wheel spindle.

front or rear?

Assuming rear, on the brake drum:

Hub Removal

1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .

1. Remove the wheel hub.
   1. Unstake the rear axle wheel hub retainer.
   1. Remove the rear axle wheel hub retainer and discard.
   1. Remove the wheel hub (1104).

What year miata?