Question about 2008 kawasaki Ninja ZX6R

Open Question

What color wire from starter button to solenoid 2008 zx6r ninja

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 132 Answers

SOURCE: I want to chang the horn in my kawasiki ninja zx6r

the horn is only held on by 1 bolt,undo this and remove the 2 wires then just reverse these steps to refit

Posted on Jun 13, 2009

  • 14 Answers

SOURCE: seriously overheating zx6r ninja

With the 05 I would check the thermostat. With the 03 that is normal, my 02 cuts on and off around the same range. I put a switch in so I could turn my fan on when ever I wanted. I run mine once I get to 175...

Posted on Jun 22, 2009

andyhazel83
  • 2 Answers

SOURCE: zx6r ninja acceleration issues

hi there i think your jets are blocked in the carbs , need to strip the carb and cleen the jets and the bowl ect.. hope this helps

Posted on Sep 25, 2009

Benimur
  • 6966 Answers

SOURCE: 00 kawasaki ninja zx6r my bike don have no power,

Hi and welcome to FixYa,

I understand that you have checked the:

  • battery - that it is fully charged and that the cables & terminals / connectors are clean and tight;
  • fuses - including the 30 Amp main fuse;
  • starter relay - there is +12 on the white wire.
Should the above hold true, then the only remaining components to suspect / check would be the always on +12 connectors and/or the ignition switch.

Good luck and thank you for asking FixYa.

Posted on Nov 18, 2009

  • 1 Answer

SOURCE: seriously overheating zx6r ninja

my bike did the same thing, and it sounds to me like your riding in a lower gear and your thermostat sensor on the radiator needs to be replaced

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

At the same time I can push start the bike and everything works fine ,clutch clutch lever everything works fine when im riding , just when I stop the bike acts like its dead , at the same time when im...


Hi, Anthony nice novella and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a "LOAD" test, your battery may show 12.5 volts but has little or zero amps and must be replaced.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand or clutch pull in switch/sensor.
10. Security alarm needs a reset.
11. Starter relay, solenoid or starter circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
ZX6R J2 2001 won start
What to do When Your Motorcycle Won Start
Kawasaki 2000 Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual

Mar 31, 2017 | 2001 kawasaki ZX-6R Ninja

1 Answer

Left Headlight not working


probably loose wiring or something like that if i was u i would take it to the mechanic

Jun 26, 2013 | 2008 kawasaki Ninja ZX6R

1 Answer

Zx6r 2004. Bike ran great for two months. Went out to dinner last night and came out to my bike not starting. Trailered it home, started when taking off trailer. Went for a 15 minute ride and parked it....


Hi, Matt it saddens me to inform you that you have to put on your Battery Priest Robe and prepare yourself for the Ceremonial "LOAD TEST" but before you begin, maintenance type batteries must be topped off with distilled Holy Water and all batteries must present their terminals to the battery charging altar to receive the electrical infusion of Holy Ions until they have reached a 100% full charge of 12.5 volts or better.
Below is a quick and easy test to see if your battery is in good condition or needs Last Rites and must be replaced.
1. Start by disconnecting the spark plug cables.
2. Adjust voltmeter to DC volts 20-volt range
3. Place the voltmeter leads to the battery terminals.
4. Turn the run/off switch to run.
5. Turn the ignition switch on and press the starter button.
6. Watch the voltmeter as your engine turns over for 15 seconds.
7. If the voltage drops below 9.5 volts, the battery is faulty and must be replaced.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
ZX6R 636 Bike won start
Kawasaki NINJA ZX6R My bike won start Starter problem or discharged battery
Kawasaki Ninja ZX6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual
How to Tell if Your Battery is Bad in 3 Easy Steps

May 18, 2017 | 2007 kawasaki Ninja ZX6R

1 Answer

How do i test a starter solenoid on my ninja 250


I normally put a screwdriver between the terminals on the solenoid to see if it starts. If it does The second thing to do is listen for a click in the solenoid when pressing the start button. If it does but doesn't turn the starter then it's the solinoid at fault not the starter button. If you get nothing when connecting the terminals it's proberly the starter motor or connections.

Mar 22, 2013 | 2008 kawasaki Ninja 250R

1 Answer

Starter motor continues to run(without starting the engine) with the kill switch off and ignition turned of and the keys removed


Most bikes are built with this setup....
the positive battery post has 2 cables....one goes directly to one side of the starter solenoid relay, the other goes to the main fuse for the bike. With the key on, when you press the starter button it completes the circuit for the relay coil, which closes the heavy contacts of the solenoid and puts power to the starter motor.
This design allows the starter button to be constructed with smaller wires as they only operate the coil, not carry all the heavy current to spin the starter.
It sounds like your starter solenoid contacts are stuck closed so power is getting through at all times.
Sometimes with battery unhooked you can tap the solenoid and free the contacts....and it may work, however its probably time to replace the starter solenoid relay.

Mar 20, 2011 | 1997 kawasaki ZX-9R Ninja

1 Answer

I have zx6r that wont start changed battery for new but all i get is a clicking sound. any ideas


Follow the large wire from the positive pole on the battery to a small relay with two large wires on it.
That is the starter solenoid, jump from one off the post to the other big post on the solenoid and see if the
starter works. IT WILL SPARK when you jump it use a big wire.
If starter works then 99% sure solenoid is bad.

Feb 06, 2011 | 1996 kawasaki ZX-6R Ninja

2 Answers

00 kawasaki ninja zx6r my bike don have no power, no lights or horn, nothin is comin on whats wrong , i check battery and fuses plus starter relay everythin is ok i just dont have no signs of power, thanks


Hi and welcome to FixYa,

I understand that you have checked the:
  • battery - that it is fully charged and that the cables & terminals / connectors are clean and tight;
  • fuses - including the 30 Amp main fuse;
  • starter relay - there is +12 on the white wire.
Should the above hold true, then the only remaining components to suspect / check would be the always on +12 connectors and/or the ignition switch.

Good luck and thank you for asking FixYa.

Nov 18, 2009 | 2001 kawasaki ZX-6R Ninja

1 Answer

I want to chang the horn in my kawasiki ninja zx6r


the horn is only held on by 1 bolt,undo this and remove the 2 wires then just reverse these steps to refit

Jun 10, 2009 | 2001 kawasaki ZX-6R Ninja

Not finding what you are looking for?
2008 kawasaki Ninja ZX6R Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...