Question about 1996 Suzuki VS 1400 Intruder

1 Answer

Coil not firing

Not firing through plugs

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Either your coils are bad, or they are not getting power, or they are not getting a signal from the pulse coils.
Check ignition fuses
Check for ~12V at coils with ignition on.
Find pulse coil connector, check resistance across leads, should NOT be zero, and should not be infinite, consider about 100 ohms OK. (These wear out more often than the coils.)
If these three checks are OK, check the primary and secondary resistance of your coils. The resistance across the wire connections on the coil body should be about 10X the resistance from the spark plug wire to the coil connection.
All the best!


Posted on Apr 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coil pak not firing 97 lesabre 3.8 relaced non firing pak, didnt help.


If three coils plugged into ignition module, and one isn't firing. One coil fires two plugs, when you remove that one coil, use a test light at ignition module primary terminals, where that coil plugs in, have a helper crank it, if the light doesn't flash, replace the ignition module. You may want to disable engine so it won't start. I can't think what else it might be? I've seen this problem before, at that time, it turned out to be the ignition module that was faulty.

Jun 14, 2017 | Cars & Trucks

1 Answer

Why are two spark plugs not firing?


This is likely a waste fire ignition system where one coil is firing two plugs. This is a less expensive system for the OEMs and is used in many models. I would swap the coil with another to assure that it is the coil and not the Spark Control Module.

If problem moves with the coil replace the coil.



26140240-lzleqmkq2il3uzgzlfgxjwff-3-3.gif Hope this helps?

Mar 24, 2016 | Cars & Trucks

1 Answer

It mayI have no fire going to the coil or from the coil to the plugs


Have you checked the wiring, the spark @ plug, Power to the coil???

Engine Won't Start No Spark - Auto Diagnosis Repair Help

aa1car.com/library/no_spark.htm
If your engine cranks normally but will not start because it has no spark, or it ... If an engine has a coil-on-plug ignition system with no plug wires, remove one of ...

No-start, No-Spark diagnosing simulated - YouTube

? 5:13
https://www.youtube.com/watch?v=XSWN1M8Hoqo
May 19, 2010 - Uploaded by FrankHurtAuto
Simulation of no start with no spark diagnosing, ... Ignition coiland module test with test light (ScannerDanner Premium lecture) - Duration: ...

getting fire from coil but not to plugs - CarGurus

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusJun 12, 2013 - 2000 dodge ram 1500 4x4 not getting fire changed distributor cap, coil, pickup ignition, rotor, plugs, plug wires 2 answers. ... 1994 dodge 5.9 just shut off and wont start back up there is no spark or fire from coil or plugs. ... 94 dodge van 318 eng will not start new plugs new crank ...

Ignition Coil Troubleshooting: (No) Fire in the Hole

www.secondchancegarage.com/public/coil-troubleshooting.cfm

Jan 27, 2016 | Cars & Trucks

1 Answer

Number 1 &4 cylinders won't fire changed the coil, plugs and wires but still won't fire.


check power and ground and signal voltage at the coil electrical plug. chances are your missing one of them.

Sep 14, 2014 | Cars & Trucks

1 Answer

Coil wont fire all three wires have power but no fire to plugs replaced twice


Crank sensor if it has one,timing belt skipped is a possibility,and always the dread security key problem.don-ohio

Apr 01, 2013 | 2001 Ford Focus

1 Answer

1993 Nissan 300zx: Number 4 cylinder doesnt fire.


Please read about misfire diagnosis and repair here.

Oct 01, 2012 | 1993 Nissan 300ZX

1 Answer

4 cyl. won't start,new plugs, wires,cap,etc.


a crank sensor tells the coil to fire.are you getting a signal at the coil to fire?

May 25, 2009 | 1995 Jeep Wrangler

3 Answers

NOT GETTING FIRE TO THE SPARK PLUGS


Hello Momtexas1:

>>Remove the Spark Plugs and Wrap the Threaded Section of the Plug with Wire, then Attach the Other End of the Wire to the Engine Block.
>>**First Make Sure the Plastic End that Snaps to the Plug is Allowing Current to the Plug. Use a Test Light or Multimeter and Check for Fire Behind this Connector (through the Large Rubber like Coil Lead to Plug) for Fire to the Plug whenever there is No Fire to the Plug.**
>>Once you are Sure the Coil Lead and Ends to the Plug are Not the Reason for No Fire to the Plug, then with the Plug Still Wired to the Engine and the Coil Lead Attached to the Plug; Remove the Coil Shut Off Wire at the Shut Off Switch.
>>Check for Fire. If No Fire, then Remove the Cut Off Wire from the Coil (removal of the blower housing required) and Check for Fire.
>>If the Spark Plugs are Firing with the Plugs Out and Properly Grounded to the Engine, then Replace the Plugs and Start the Engine.
>>Using an Insulated Plug Wire Puller, Pull the Plug Wire from 1 Cylinder. If the Engine Continuse to Run, then Replace the Plug Wire and Disconnect the Other Plug Wire. If the Engine Quits, then Replace the Other Cylinders Coil.
Send me the Model and Type or Spec Numbers Off the Engine and the Mower Model Numbers, Please. With these I can Locate the Proper Manual and Better Assist you. The Engine Model Numbers May be Stamped Into the Blower Housing (metal engine cover) Above the Spark Plug. The Mower Model Numbers are Usually Located Under the Seat on a Sticker on the Body of the Mower.
>>Thanks.

Respectfully

John

Apr 13, 2009 | Craftsman 42 in. Deck 19.5hp Lawn Tractor

Not finding what you are looking for?
1996 Suzuki VS 1400 Intruder Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...