Question about Harley Davidson XL 1200 C Sportster Custom Motorcycles

1 Answer

Exhuast stud torque setting - XL 1200 C Sportster Custom Harley Davidson Motorcycles

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Be careful,you dont want to over tighten and break studs ,just use lock washer and snug up,thats all,done lots of exhaust changes on my 94 Wide Glide quite easy,take care.

Posted on Apr 17, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3567 Answers

SOURCE: torque settings for the head bolts on a 1984 xc 125 husky

The stud is 8mm with 1.25 thread. the torque, according to the service manual, is 19.6 to 21.6 Nm or 2.0 to 2.2 Kgm or 14.5 to 15.9 lb/ft.. It all depends on your favorite language.

Please take a moment to rate this answer. Thanks silverfernwe!

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque does it take to break a standard wheel stud?


it is tension that breaks a bolt not torque
you would have to put the stud through a piece of metal and make the nut stretch the bolt to make it snap and measure that required torque
the torque will be in excess of 100ft/lb

Aug 12, 2017 | Cars & Trucks

1 Answer

Free answer "93 Lexus head bolt torque


it means that after the initial torque setting of 25 ft/lbs you put the torque wrench away and use a socket and bar to move the head of the bolt the required number of degrees as per the angle gauge that you will fit over the head of the bolt
so select the first hard stud and torque to 25 ft/lbs
repeat this to all the other head studs in the pattern required to achieve even tightening of the head
put the torque wrench away and fit the angler meter (gauge) on the 1 st stud and tighten to 60 degrees as indicated on the gauge
repeat the process for all the head studs as per the tightening sequence
then start again and tightened again another 60 degrees and so on
modern engines use degrees to achieve the correct stretch of the bolts to get the prescribed crush on the gaskets
this is because engineers found that dry threads , dirty threads and dirty stud holes do not give repeatable tensions on all studs.

May 19, 2015 | Lexus Cars & Trucks

1 Answer

Exhuast stud tourque setting


If you mean the nut that threads onto the stud to compress the exhaust pipe flange, 10-15 Ft-Lbs

Apr 12, 2014 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

What are the torque setting for the front discs on a 2003 ford transit


if your doing wheel bearings and youve never done this before,id take it to a mechanic ,there are no torque settings its about experience

Feb 03, 2012 | Ford Transit Connect Cars & Trucks

1 Answer

Head stud torque


cyl head torqes.1st stage 29 nm. 2 nd stage 57-67 nm. 3rd stage slacken off 360 cegrees, 4th stage 29 nm. 5th stage 64-74 nm. intake and exhaust valve clearance .38 mm hot setting. hope it goes ok.

Aug 14, 2009 | 1987 Nissan King Cab

1 Answer

How to install twin kadrons on a stock 1600 and do i need to install anything else first


fuel pressure needs to be between 1.5 and 2 psi (after the fuel filter) unbolt the throttle cable and remove all hoses from the existing carb. remove the air cleaner. unbolt the intake from the heads and from the exhuast. remove the whole assembly from the vehicle. go ahead and set your valve clearances. plug the preheat hole in the exhuast manifold. install the studs on the intake. apply a little oil on the mating surfaces then apply the gasket, install the carb onto the manifold and the manifold onto the head. do the same for the other side. install the linkage and filter. set the jets all the way in on both sides then back them out two full turns and that should get you to where you can start it. then sync and adjust them accordingly.

Jul 08, 2009 | 1998 Volkswagen Beetle

1 Answer

Taking torque converter inspection plate off 86 s10 blazer


Hello tapout383: My name is Roger and I will answer for you. There is no way to remove the flywheel cover with out dropping the exhaust. I have tried every way you could imagine. You will also need to replace the donut gaskets when you put it back together.Be careful not to break the exhaust studs when you loosen them. Good luck on your repair. Please rate the quality of your answer. This is how we track you received the correct answer. Thank You for using FixYa. Roger

May 06, 2009 | 1986 Chevrolet S-10 Blazer

1 Answer

Torque settings for the head bolts on a 1984 xc 125 husky


The stud is 8mm with 1.25 thread. the torque, according to the service manual, is 19.6 to 21.6 Nm or 2.0 to 2.2 Kgm or 14.5 to 15.9 lb/ft.. It all depends on your favorite language.

Please take a moment to rate this answer. Thanks silverfernwe!

Apr 15, 2009 | 2001 Husqvarna SM 610 S

1 Answer

Exhuast leak manafold bolt stipped


you need to drill out the manifold bolt and replace the stud,  Or buy a used manifold from the junk yard

Mar 26, 2009 | 1991 Toyota Pickup

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...