Question about BMW R 1150 RT (ABS Motorcycles
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: HOW DO YOU BLEED THE
i think it should be just like a car this could be a 2 person job have some one pump the brake 10 times and hold it on the last one and you loosen the bleeder bolt it gona squirt then tighten it back up and have them let go of the brake also check your fluid level after everytime try that
Posted on Apr 29, 2009
I just by-passed the ABS system and the front breaks work perfectly! I don't care much for ABS... It's not like I'll be slamming on the breaks down the road at high speeds. I'm off to do the same on the rear breaks tomorrow.
Posted on Sep 02, 2009
SOURCE: my bike is a 2002
Low voltage has been blamed for ABS faults on a number of bikes, and those bikes have been fixed by going to a different battery, usually a sealed one. Sealed batteries have significantly higher voltage due to the chemical differences, usually about 12.85 to 12.95, instead of the 12.60 to 12.80 typical of flooded designs
If the lights initially flash together but alternate after you start the bike, you can try the "rolling restart." Ride away with lights flashing and on a straight section of road, in third gear or higher and maybe 2500 RPM, pull the clutch in and turn the key off with your right hand. Coast for one or two seconds, then turn the key back on and release the clutch to "bump-start" the motor. If the lights are flashing together, you're in luck, and next time you come to a stop and pull away you should get a successful ABS self-test. If so, you need a new battery or you have some other charging system problem. If not, you have some other fault.
There is also a modification you can make so that the ABS unit is not powered up until after the motor is running; this will also cure low-battery problems.
BMW batteries often (in my experience) have quite low voltage. This might be a carry-over from the days of the airheads, where cranking current was vital, but voltage wasn't. As you go to higher voltages, the cranking performance can suffer a bit, especially at low temperatures. More importantly, they are harder to recharge - an important point for most airheads. I have seen Mareg (BMW) batteries on properly functioning bikes at 12.40 volts and lower, fully charged, engine off - well below what is considered (I think by BMW) to be the minimum for good ABS operation.
Dealers get the electrolyte for the batteries locally - not from BMW - so this aspect of the battery is not really BMW-controlled. Different dealers could be using different strengths of electrolyte. The article explains how this affects voltage. If your fully charged battery is at too low a voltage due to weak acid being used to fill it, you MAY be able to successfully raise the voltage by use of fresh electrolyte.
Theory only! A way to do this would be to fully charge the battery, discharge it to a point where the electrolyte specific gravity is about .030 below the new electrolyte you have, then empty it and quickly refill with the new stuff. This will give you maybe a .020 increase in gravity and a 0.2 volt improvement. Don't shoot for anything higher than 1.285 or so. Remember, for a 12V battery the voltage is roughly ten times the acid gravity. 1.260 S.G. gives you around 12.60V. And don't let the battery stand without acid in it.
If your problem is that the voltage drops too much when the key goes on, then the above IS NOT your problem. You probably want a stronger, or newer, battery. The success of the new sealed batteries in this area is largely due to the fact that the voltage doesn't drop as much while cranking, rather than simply higher overall voltage. This is a function of plate area, etc...
hope this helps
Posted on Mar 28, 2011
Tips for a great answer:
Apr 16, 2014 | 2002 BMW R 1150 RT (ABS)
Mar 02, 2014 | BMW Motorcycles
Jan 20, 2014 | 2002 BMW R 1150 RT (ABS)
Jan 20, 2014 | 2004 BMW R 1150 RT (ABS)
Dec 13, 2013 | 2002 BMW R 1150 RT (ABS)
Aug 02, 2013 | BMW R 1150 RT (ABS Motorcycles
Apr 11, 2013 | 2004 BMW R 1150 RT (ABS)
Mar 30, 2010 | 2002 BMW R 1150 RT (ABS)
77 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: