Question about 1990 kawasaki ZXR 750

1 Answer

Wont start, it was found that the carburator release too much gas while the others not.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Strip and clean your carbs, set the float-heights back to standard making sure the float needles are in good condition.

Posted on Jun 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Carburator choke wont set on 1984 honda hatchback when pumping the gas pedal. car wont stay running

Most carburated engines you don't pump the gas pedal, you slowly press it all the way to the floor one time and release it, then you attempt to start it. The problem that you are describing is an indication that the carburetor needs to be rebuilt. The choke plate has a latching mechanism that is connected to a heater coil, if there is excess wear on the parts or the heater is bad, it has to be replaced

Dec 10, 2016 | Honda Cars & Trucks

2 Answers

Mower died when I engaged the cutting blades. Won't restart.

How long has it been since you used it? Could be a clogged carburator filter or bad gasoline. Gasoline left in lawn mowers and other small engines lose their kick after sitting for a fall and winter season. Try removing the carburator cover and take some fresh gas, just about a little less than 1/8 of a cup and pour it in the carburator and try to start the engine. Once it starts cover the carburator with the palm of your hand and then release it and cover again until the machine stays on after you remove your hand. This is called priming the engine.

Jun 18, 2015 | Ariens Max Zoom 60 in. 25 HP Kohler...

1 Answer

My Kawasaki 650 sr 1978, wont start,is gas problem because,I start on the bike and in 5 seconds turn off,carburator are clean gas valve has 2 gas out let looking just 1 out let sended gas to the...

arnt the one the vacuum pipe, between the carburator and the sleeve barrel is n nipel were the vacuum pipe must come one it sucks the and open the valve to let the caburator so it can get petrol just see maby im wrong

Feb 01, 2015 | kawasaki Motorcycles

1 Answer

My klx 125 wont start without starter fluid. after its running it wont idle. if it shuts down it wont start again

1.) first check to see that gas is getting to the carburator
2.) check for a dirty air filter
3.)Take your carburetor apart, remove the bowl and soak in carburator cleaner

Oct 26, 2014 | Motorcycles

1 Answer

Poulan pro weedeater will not start without starting fluid and wont accelerate after starting Once started the first time it is easy to restart and idles fine, just cant accelerate the motor without it...

Your carburator is clogged.
1st make sure you have FRESH gas.
Empty and clean the fuel tank
Remove and disassemble the carburator and soak it in fresh gas for about 15 minutes to disolve any gunk.

Using a can of small carburator cleaner ( available at Lowes, Home Depot etc.) blow out all the ports.
reassemble and refuel with clean fresh gas
The little carbs clog easily

May 19, 2011 | Poulan/Weed Eater No. Te475 952711797 17"...

1 Answer

Very hard to start, i pull and pull and pull on the cord but it wont start i do prime it every third pull any ideas?

Chances are your carburator has dirt in it.
It doesn't take much to clog those little carbs.
Empty the gas tank and clean it.
Purchase a can of small engine carburator cleaner. Comes in a spray can for about $5 at Home Depot or Lowes.
Remove the carburator and disassemble it.
Soak the body in clean gasoline for about 15 minutes if you can agitate it do so to help the gas disolve any clogs.
Clean the ports with the spray cleaners to blow out any debris.
Reassemble and remount the carb.
Remove, clean and gap the spark plug
Refuel the gas tank with new clean gas

May 07, 2011 | Ryobi Garden

1 Answer

I have problems starting my eton 70 cc four stroke. it turns over but wont start is there atrick to starting these

If the Fuil is old it wont start and if the mixture is to rich it wont start. Other then that check the plug for signs of Fuil and if none then clean the carburator and lines.

Sep 24, 2010 | Gas Gas EC 125 Motorcycles

1 Answer

Toro lawn mower wont start

pour alittle gas in carburator & then try starting see what happen if it starts & then dies then you have a carburator problem

Nov 09, 2009 | Toro Lawn Mower With Toro Power Tools

2 Answers

Riding lawnmower wont run long

Check for dirt in gas tank some times stuff will fall in when filling and block the hole in bottom of gas tank and wont let gas flow clean everything out and see if it works. Also check that all kill switches are tight and not moving.

Oct 09, 2009 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

Not finding what you are looking for?
1990 kawasaki ZXR 750 Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5042 Answers


Level 3 Expert

81285 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides