Question about 2007 kawasaki Z750

1 Answer

04 z750 clocks resetting

I have 2004 z750 doing the same thing, clock and trip resetting each time I turn ignition off, odo fine, started as intermittant fault but has now started doing it each time ?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

There should be a wire that runs from the cluster to your battery that gives the cluster constant power. There is probally a short in that wire. The odo doesnt do it because it has a memory board.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to know how to reset my clock in my 2005 Honda inspire car. the dash is all set out in Japanese.


Don't know your car but clock on a lot of cars is controlled by the other button near the odo reset - press and hold till clock flashes, these buttons are normally near speedo and rev counter normally ignition on engine off then sometimes your button turns left or right to adjust. Either that or search for images of your car and it's clock.

Jan 01, 2015 | Honda Cars & Trucks

1 Answer

I cant reset MAINQ on a Lexus Gx470 2004 how I reset it?


turn ignition on then off. now, with odometer showing hold the odo/trip button down and while holding button down turn ignition on and continue holding for about 10 seconds. light should flash a couple of times then go out

Dec 05, 2013 | Cars & Trucks

1 Answer

How to tun off timing light after changing the belt


with ignition turned on, using the trip switch , change the display to ODO, and then turn the ignition OFF
While pressing the trip switch,turn the ignition switch ON and hold for five seconds
Release the trip switch,then press the switch again within five seconds.The digital display should change to T- BELT MODE. Each press of the switch then should change the reset time by 10,000km increments. After setting the klms hold the trip switch ON for more than five seconds then release the switch. Check that the display has now changed back to ODO and that now the warning has gone off when the engine is started .

Dec 28, 2010 | 2006 Toyota Land Cruiser

2 Answers

How do I reset the computers timing belt information in a Toyota 2007 4.7L (VIN T, 5th digit, 2UZFE eng, 8 cyl) after making a timing belt change?


1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display "15" (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once " 20 " (200,000km) is reached the display reverts back to " 1 " (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn't need to change from the default setting of "15".
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.

Oct 30, 2010 | Toyota Tundra Cars & Trucks

3 Answers

2005 lexu 330, turn off maintenance light


1. With your car OFF, place your key in the ignition and turn to "On". Do not start the car.
2. Find the odometer button and press until it reads the total odometer setting, (not the Trip A or Trip B setting).
3. Turn the key to OFF.
4. Place your finger back on the odometer button, press and hold. At the same time, turn the key back to "On".
5. Hold the odometer button in until the MAINT REQD light goes out...should take about 8-10 seconds.

page 77 of the 2004 Lexus rx330 handbook...
(you will find the answer you are looking for in resetting your maintenance light.)
with the odometer reading visible, (not trip A or trip B..) turn off engine.

While keeping Odo/trip button depressed, turn ignition back on (not starting the engine) You will see dashes (instead of numbers) on your odometer disappearing one at a time. it will be replaced by 0's (zeros).. Release the Odo/trip button and your original mileage will come up....
And your done..... until the next oil change.

Thank you for using fixya and good luck

Oct 10, 2010 | 2005 Lexus ES330

2 Answers

Hi How do i reset my service light on my 2004


press and hold trip meter reset button with ignition off. switch on ignition while holding button. release button when ignition is on and then turn clock setting button to the right and hold for a few seconds until service light resets.

May 14, 2010 | 2004 Volkswagen Passat

2 Answers

How do i turn of the timing belt light on my 04 landcruiser 3 litre


Ive never heard of a timing belt light, but there is a maintenance light that can be reset. Here the procedure:

To reset the maintenance reminder light: Turn the ignition switch to the "ON" position. Set the odometer/trip display to the odometer (ODO) mode. Turn the ignition switch off. Depress and hold the trip meter reset button while turning the ignition switch to the on position. The maintenance reminder light will, illuminate for 3 seconds, blink for 2 seconds, illuminate solid for 1 second and then turn off. Release the trip meter reset button. Turn the ignition switch to the off position. Turn the ignition switch to the on position. Confirm that the maintenance light goes out.
Let me know if this helped you out!

Mar 29, 2010 | 2004 Toyota Land Cruiser

1 Answer

The maint light is on I have a 2004 toyota 4 runner sport


This is basically your change oil light. When you have your oil change done, the shop should have reset the light for you.
To reset the light, try doing this:
Turn the ignition on
Make sure the odometer displays "ODO"
1.Turn the key off
2.Press and hold down the same button you use to get to "ODO"
3.Turn the key back to ON ( while still holding down the button)
4.Hold the button in until all the flashing lines on the odometer go away and the bunch of "000000" shows up and the maint reset light will turn off.
Your'e done.

If this doesn't work, you would have to try it on "trip A" instead of "ODO".

Apr 09, 2009 | 2004 Toyota 4Runner

1 Answer

Oil change light


Turn the key on. Observe the odometer. Is "ODO" displayed? If not, push the trip meter button until "ODO" is displayed, with the total mileage travelled shown.
Turn the key off.
Push & HOLD the trip reset button until advised to release it.
Turn the key to "ON" (do not start engine)
Observe the ODO display.
You should see 5 dashes, then 4, then 3, then 2, then one, and finally, five zeros.
The original mileage that you observed should be redisplayed.
Release the trip reset button.
The proceedure is now complete.

Jul 29, 2008 | 2004 Toyota Corolla

Not finding what you are looking for?
2007 kawasaki Z750 Logo

Related Topics:

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...