Question about 2007 Suzuki Boulevard

1 Answer

Took apart starter button/kill switch need a picture to make sure i put ir back right

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do mix stroke oil on a cr 250 1997 model?
and where do add what oil?

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bike won't start(lights light ,horn works push starter button nothing no power to spark plugs ??? i belive one of the starter interlocks must be stuck in an open position possibly?


Hey, When that happened to me I took the bike half apart and it ended up being the Kill switch. Try rocking it back and forth also if you have contact cleaner flood the switch and let it dry then give it a light spray of wd-40. also check the start switch to be sure it is making contact,bike is in Neutral and the kick stand switch is also working.

Jul 07, 2011 | 2000 Honda Valkyrie Interstate

1 Answer

I have an 82 xj650 turbo. My problem is when i shut the key off it does not kill the engine. If i use the kill switch the bike will shut off along with the tail light but all the lights on the front of the...


I think your bike is being powered through the starter solenoid by a defective starter button. The starter button is on the right switch assembly and normally turns the headlight off when depressed halfway. A wire may be plugged in wrong in the headlight (Two wires are crossed). Take apart the right switch assembly and check for shorts and power from the solenoid ). Check the main wire harness to the handle bar switch for crossed wires (they are color coded).

Mar 15, 2011 | 1982 Yamaha XJ 650

2 Answers

Starter wont engage.


Are u crossing the terminal at the button end or the starter motor terminals? if the termianal u r crossing is at the starte end check the button terminal end and cross them. It could be just abadly corroded button. If not that replace the starter relay, buy a haynes mannual to see where is located, the mannual will be a good investment.

May 31, 2010 | 1984 Yamaha FJ 1100

1 Answer

03 gsxr 600 has broken wires on connector from r/handle switches!


Unless someone has a bike and gives you the correct information you will be fine. Otherwise I recommend tracing back. Also if you turn on ignition, ensuring wires are not touching each other. Ignition will be hot and you should have a common ground. Kill switch will not be a ground. Start switch should be same color as the one at starter. Also turn signal on left handle bar will cause intermittent power to connector. It may just be easier taking apart switches on right handle bar. Or inspecting where they are actually coming from specifically.

Feb 21, 2010 | 2003 Suzuki GSX-R 600

1 Answer

I have a york 90%+ furnace the inducer fan fills with condensation passing into the pressure switch. I have took apart the condensate pump motor cleaned it and the pan,I have blown thru all condensate...


Make sure that the drain line outside is only about 6" long it may be freezing up. Does the Condensate pump have a safety switch to kill the power if it runs over? If it does it should kill power to the heater. Make sure the drain has a fall. Check the install manual to make sure the hoses are hooked up right.

Jan 04, 2010 | Heating & Cooling

1 Answer

Jus bought a 91 ninja 600 and wont send any power to the starter


Lets start with the basics...
1. be sure your battery is in good shape and fully charged ( at least 12.6 volts)
2. starting procedure- ignition key to 'on', tranny in nuetral, right hand kill switch to 'run', pull clutch in fully and hit starter button.
3. does it do anything? clicks?... If you get nothing then the problem is likely in the clutch switch, kill switch, or the starter button. You will need a wiring diagram and volt meter to trace down where the power is lost. If you are getting 12 volts to the starter but its not engaging then you can suspect the starter/ solonoid.

PS... My clutch switch has been going bad for a few years now ( Im too lazy to replace such a trivial thing as a safety switch ;). Sometimes I need to hold the start button and work the clutch till the starter engages.

Jan 04, 2010 | 1991 kawasaki ZZR 600

1 Answer

NEED A PICTURE OF THE STARTER SOLENOID CONNECTED


the top two wires dont matter a solenoid is just a switch when you send juice to the solenoid via the small wire it connects the two on the top

Dec 06, 2009 | 1989 Ford F 150

3 Answers

I have a 2000 Honda Shadow 750 ACE. While riding at highway speed I accidently hit the kill switch. At first wasn't sure what had happened. Realized it was a fuel issue... noticed it was the kill switch....


Take the starter button off and put a 12 volt tester on one of the 4 leads that are wired into the button. Test each- If you find a hot line, take a small piece of wire and jump the current over to the other parrallel button. I worked on my bike for two weeks before I discovered this problem. Another problem was that the headlight would not come on. The starter would not crank at all. I took a screw driver and raised the brass leads on the switch so they would make contact and put the switch back together, and it worked. Good luck.

tim reynolds

Jul 18, 2009 | 2002 Honda VT 750 CD Shadow A.C.E. Deluxe

3 Answers

Scooter does not start with button,but start with the kick


what does it do when you push the start button?? click or just does nothing??
is there power to the starter when you push the start button??

May 05, 2009 | Tomos Se 125 F Motorcycles

1 Answer

Patton U2 1887 Fan Won't Run After Cleaning


Do you have the cover back on unit tight has a button that kills the circuit when cover is taken off. Be sure it is on. Get back with me if that isn't it. ken

May 02, 2009 | Heating & Cooling

Not finding what you are looking for?
2007 Suzuki Boulevard Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...