Question about 1993 BMW K 1100 RS

1 Answer

K1100RS (1993 Model) ABS Issue

Just had the ABS indicator start flashing in unison with the warning light. Is there an easy way to troubleshoot - ABS module, Fuse, Sensors??? The indicators will both go solid when the ABS by-pass switch is pressed - they will start flashing again about 15 minutes later. There does not seem to be any other issues.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

Unfortunately I suspect your ABS pump has gone.
The only cure is a replacement.

Posted on Jun 27, 2009

  • Flatly Faceless
    Flatly Faceless Apr 15, 2013

    How old is the battery and how often do you drive the bike? ABS system does a power up check, first thing is checks is battery voltage, I believe it needs a minimum of 12.6 volts not running. After that do an ABS reset, procedure can be found at BMW rider sites. There is also a procedure to read the fault codes at a special test connector, located under seat on right side, dark blue plug on connector, test procedure can be found on the internet.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Nissan pu speedometer quit working


SPEEDOMETER TROUBLESHOOTING


Can be loose speedo wiring connectors under instrument panel or its issue with speed sensor on transmission.


I suggest you to go through help links mentioned below with appropriate solutions to confirm the problem :------


How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

-----------

1996 fiat bravo speedometer not working?

http://technoanswers.blogspot.com/2012/01/1996-fiat-bravo-speedometer-not-working.html
------------

Speedometer works but odometer not working?

http://technoanswers.blogspot.in/2012/01/speedometer-works-but-odometer-not.html

-----------

Speedometer runs backward?

http://technoanswers.blogspot.com/2012/01/speedometer-runs-backward.html

-------------

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.ht

-------------

Speedometer not working on 1993 Ford F350?


http://repairhelpcenter.blogspot.in/2012/02/speedometer-not-working-on-1993-ford.html

----------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------

Vehicles Cluster panel Not reading Miles?

http://schematicsdiagram.blogspot.com/2011/12/vehicles-cluster-panel-not-reading.html

-------------

Odometer works properly but speedometer works intermittently?

http://technoanswers.blogspot.com/2012/01/odometer-works-properly-but-speedometer.html

-------------

These will help.

Thanks.

Feb 04, 2013 | Nissan Cars & Trucks

1 Answer

98 jetta error code p0101


Can be loose speedo wiring connectors under instrument panel or its issue with speed sensor on transmission.

I suggest you to go through help links mentioned below with appropriate solutions to confirm the problem :------

How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

-----------

1996 fiat bravo speedometer not working?

http://technoanswers.blogspot.com/2012/01/1996-fiat-bravo-speedometer-not-working.html
------------

Speedometer works but odometer not working?

http://technoanswers.blogspot.in/2012/01/speedometer-works-but-odometer-not.html


-----------

Speedometer runs backward?

http://technoanswers.blogspot.com/2012/01/speedometer-runs-backward.html

-------------

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.ht

-------------

Speedometer not working on 1993 Ford F350?


http://repairhelpcenter.blogspot.in/2012/02/speedometer-not-working-on-1993-ford.html

----------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------

Vehicles Cluster panel Not reading Miles?

http://schematicsdiagram.blogspot.com/2011/12/vehicles-cluster-panel-not-reading.html

-------------

Odometer works properly but speedometer works intermittently?

http://technoanswers.blogspot.com/2012/01/odometer-works-properly-but-speedometer.html

-------------
These will help.
Thanks.

Nov 27, 2012 | 2008 Volkswagen Jetta Wagon

1 Answer

1993 Buick lasabre when I start my car the heating display numbers flash repeatedly. My heat is working fine what is this and how do I get it to stop


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Oct 25, 2012 | Cars & Trucks

1 Answer

ABS light comes on... but no noticble degradation in operation etc.


Most likely a wheel speed sensor, hopefully... The only thing that will change when the ABS light is on is that the ABS will not function as long as the indicator is on. I hope this info helps.

When the airbag system is in functioning condition, the airbag warning light will remain on for about 7 seconds and go out when the ignition switch is set to ON .

If there is any malfunction, the airbag warning light will either stay on or off continuously. In such cases, perform on-board diagnostic in accordance with the specified procedure to determine trouble codes.


  1. Turn ignition switch ON (with engine OFF ).
85091723



  1. Connect DIAG. terminal to No.2 terminal of diagnosis connector located inside lower cover.
  2. Check in accordance with the trouble code indicated by the AIRBAG warning light, and record the trouble codes.
  3. Turn the ignition switch "OFF " and remove the DIAG. terminal from No.2 terminal of diagnosis connector.
85091724


HOW TO READ TROUBLE CODES
The ABS lamp flashes a code corresponding to the faulty parts.

The long segment (1.2 secs on) indicates a "ten", and the short segment (0.3 secs on) indicates a "one".





NOTE: This is the only information provided by the manufacturer for clearing diagnostic trouble codes.

97511505


CLEAR MEMORY
After eliminating problem as per trouble code, clear memory as follows:

Make sure ignition switch is ON (and engine off). Connect one DIAG. terminal (1) on diagnosis connector (2) terminal No.1.

where warning light is flashing, connect the other DIAG. terminal (3) on terminal No. 2 for at least three seconds . After memory is cleared, normal warning light flashing rate resumes. (Warning light flashes every 0.6 seconds (ON-OFF operation.) Memory cannot be cleared if any problem exists.

After clear memory and then DIAG. terminals (1) and (3), extract from diagnosis connector (2)

Jul 27, 2011 | 1999 Subaru Legacy

2 Answers

I have a 1993 VW Passat VR6, My problem is when I try to start it, I have no spark from the spark plugs..What could be the problem or how do I fix this?????


GO TO THIS SiTE TO CHECK THE FUSE BOX!
http://vwtech.no-ip.info/images/golf/post90.gif

This are the FUSE and RELAY number SLOT!
Fuse No. Description Ampere Rating 1 Headlight, low beam, left 10 2 Headlight, low beam, right 10 3 Instrument panel lights, license plate lights 10 4 Glove compartment light 15 5 Wiper/washer 15 6 Fresh air blower 16-valve only: Air conditioning 20 7 Taillights, side marker light, right 10 8 Taillights, side marker light, left 0 9 Rear window defogger 20 10 2.0 16-valve only: Fog lights 15 11 Headlight, high beam, left,High beam indicator light 10 12 Headlight, high beam, right 10 13 Horn 16-valve only: Radiator cooling fan 10 14 Back-up lights, washer nozzle heaters 10 15 2.0 16-valve only: Engine electronics, stabilizer valve, cold start valve 10 16 Instrument panel warning lights, 16-valve only: Multi function indicator 15 17 Emergency flasher switch, turn signals 10 18 Fuel pump, oxygen sensor heater 20 19 Radiator cooling fan, air conditioning 30 20 Brake lights, cruise control 10 21 Interior lights, digital clock 16-valve only: Luggage compartment light,multi function indicator, central locking 15 22 Radio, cigarette lighter 10
Relays Relay No. Description 1 Air conditioning 2 Open 3 Digifant control unit 4 Load reduction relay 5 Low coolant level control unit or Open 6 Emergency flashers 7 Rear Wiper 8 Intermittent wipers 9 Seat belt warning system control unit (possibly headlight warning too?) 10 Fog lights 11 Horn 12 Fuel pump (except diesel)Glow plugs (diesel) 13 Radiator cooling fan after run (except 16-valve)2.0 16-valve: Starter interlock relay 14 Automatic trans., coolant temperature indicator,starter interlock relay (except 2.0 16-valve)2.0 16-valve: Radiator cooling fan after run 15 ABS pump relay 16 ABS relay 17 Heated seat control unit, driver 18 Heated seat control unit, passenger, or power seat circuit breaker 19 Automatic transmission 20 Open 21 Power window relay, ABS hydraulic pump fuse 22 ABS valves fuse 23 Air conditioning, power seat fuse 24 Power window fuse

Nov 17, 2010 | 1993 Volkswagen Passat

1 Answer

1993 S500-yellow light started flashing on the instrument panel. Round circle with 3 dots on both sides, between the ABS and Brake on the instrument panel


that light is your warning light for the brake pads. One of the brake pad sensors is starting to touch the rotor causing the light to come on or flash. Have the brakes checked. You will probably be needing to replace the brakes and the sensors.

Oct 08, 2010 | 1993 Mercedes-Benz S-Class

3 Answers

My 99' volvo v70 continually flashes the traction control and abs warning light and the speedometer stops working the trip meter and the odometer go blank than all of a sudden it will start working again...


Sounds like a bad ABS control module is at least part of your problem. The symptoms are usually and ABS and TRACS light intermittent or constand and eventually your speedometer works intermittently or totally quits. This guy rebuilds/upgrades them for about $140. New ones run over $800. http://home.earthlink.net/~vicrocha/Volvo_Parts/Volvo_ABS_removal.htm

Jul 05, 2009 | 1999 Volvo V70

2 Answers

Warning lights ABS (amber) and Brakes (red)


hello this is a common problem with the dakota ,ohm out your rear abs sensor on the rear end pumpkin.If it is open then both lights will come on .the sensor is not expensive at all or hard to.

Jun 28, 2009 | 1993 Dodge Dakota

1 Answer

Indicator is turning on but not flashing.


Assuming ALL bulbs work including the warning lights on the dash, it sounds like a faulty flashing indicator relay to me. Try a replacement.

Apr 07, 2009 | 1993 Suzuki GSX-R 600

1 Answer

ABS light


It is picking up a signal from one of the wheel sensors probably.

Go here to read files on ABS issues

http://autos.groups.yahoo.com/group/villagerquest/

  • Anti-Lock Brake Warning Indicator Always On
  • Fuse(s).
  • Circuit.
  • Hydraulic solenoid relay.
  • Hydraulic pump motor relay.
  • Brake anti-lock sensor(s).
  • Hydraulic anti-lock actuator assembly.
  • Anti-lock brake control module.
  • GO to ABS Quick Test .

QT5 PERFORM ABS TROUBLE CODE RETRIEVAL
  • Key OFF.
  • Jump Pin 4 of the data link connector to ground.

    5939e8a.gif

  • Key ON.
  • Observe the anti-lock brake warning indicator.
NOTE: The first code to flash will be the start code (12). Also, each code is repeated three times before proceeding to the next trouble code.

Does the anti-lock brake warning indicator flash codes? Yes No RECORD code(s). GO to the following ABS Trouble Code Identification Chart in this section and PERFORM Pinpoint Test specified for first code retrieved. If indicator is illuminated constantly, GO to Pinpoint Test D1 . If indicator is not illuminated, GO to Pinpoint Test A1 .


df42bc3.gif

Jan 02, 2009 | 1993 Mercury Villager

Not finding what you are looking for?
1993 BMW K 1100 RS Logo

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

phil cuzins
phil cuzins

Level 2 Expert

79 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...