Question about 2001 Yamaha V Star Custom

1 Answer

I am looking for the part called the ''worm'' and am unable to locate that part alone without having to buy the entire rear drive shaft. Any ideas where to find that one piece. I have a 2001 V Star Custom 650.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 311 Answers

If you call it a pinion shaft you will get more response,try bikebandit .com

Posted on Jul 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a pro alpha 2000 garage motor. I need to remove the worm shaft coupling to separate the motor from the worm shaft. How do I do this?


Looks to me like you would push the C clip through the shaft. Have fun replacing it without the specific tool!

Sep 16, 2017 | Building Materials

1 Answer

Vibrating rear propellor shaft


could be worn axle bush's ,they hold drive assembly to chassis , if worm would cause they dive assembly to 'roll' back and forward esspecially when under most torque

Mar 28, 2014 | 2007 Suzuki Grand Vitara 4WD

1 Answer

Kia 2006 front differential rightside bearing


Firstly! GET MORE THAN ONE QUOTE FOR A PRICE!! This could turn into a BIG job needing specialist tools so If they're all about the same price, pay the money! Sand added to bearings is like sandpaper on bare skin. Either that or buy a new car.

Dec 19, 2017 | 2006 Kia Sorento

1 Answer

Tru-test tiller parts


Is there a bushing on the front of the drive on a tru-test tiller

Apr 11, 2012 | Garden

1 Answer

Is there a way to change the rubber bearing on the drive shaft without buying the entire $900 part from Porsche?


yes and its called a carrier bearing first you have to remove the drive shafts get them onto a bench so that they can be separated but remember to mark them so you install them exactly as you found them this will help keep everything perfectly balanced.you might have to use a hammer and a chisel to remove the old one its always best to have the new one on hand so you can look at it and know what has to be removed not bad to do good luck.

Nov 20, 2010 | 2004 Porsche Cayenne

3 Answers

Front drive shaft has a bad grinding noise and the rear seal has cracked and the bearings are exposed and all the grease has leaked out. do i need to replace the entire shaft and what is the diffuculty and...


If you are talking about only the drive shaft joints being bad,take it out and take it to a driveshaft repair shop. Look in the yellow pages or call a trans shop and ask who they use to check,straighten and balance drive shafts. About $150.00 and may do it while you wait. Might as well put new joints in the rear one and balance while your there.

Feb 08, 2010 | 2002 Jeep Liberty

2 Answers

Rear drive shaft


sorry to say but that is true it comes as one piece it is a press fit into place. not the best design true but it is what it is.

Sep 10, 2009 | 2004 Volkswagen Touareg

1 Answer

Pride elite traveller 4 a knock when driven coming from drive


hi,

Sounds to me like the worm drive is slipping , this can happen when the worm drive small bearing is worn,

If you do take it a part , please take great care, the shaft from the motor will have a worm drive, two bearings on the worm drive,

Try to move the shaft within the bearings, I paid £10 for replacement bearings.

Please give me a update.

Regards
GeWiz.

Jul 17, 2009 | Pride Mobility Products Health & Beauty

4 Answers

Not printing at all. Screen appears as series of exclamation marks


I had the same problem with my label marker. Changing the batteries fixed the problem

Jan 08, 2008 | Dymo LabelManager 300 Desktop Labelmaker...

Not finding what you are looking for?
2001 Yamaha V Star Custom Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Tom

Level 2 Expert

314 Answers

vince

Level 3 Expert

1216 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...