Question about 2005 Honda CRF 150 F

1 Answer

One of the plastic lines has come of on my Honda CRF150 and I don't know where it goes. One end is attached near the gas tank. There is a small opening near the kick-start. Does it go in there?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 125 Answers

It may be a vent or drain and is not supposed to be connected.
Look in the front of your owners manual, there should be a picture showing all of the lines and where they go.

Posted on Jun 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Poulan chainsaw 2001 usa epa ph1 35 cc ser. 010730200112-5. family-1pwes.0424cs:em. the plastic tubing between the carburator,primer and the gas tank broke in two or three places. i am...


No they don't join together. One goes in and the fuel filter is attached to it. The other is the fuel return line, and that is the one that is attached to that plastic part. It is usually a one way valve and nothing else is attached to other end. To get the line in the tank get a small stiff wire, put it through the fuel line hole and other end through filler neck. Wrap the wire around the end of fuel line about 2 to 4 times and pull it through helping it along by pushing on line. I think you see where I am going with this so use your own judgment also. I hope this helps you out a little bit. Regards and good luck.

Dec 13, 2010 | Poulan Garden

1 Answer

I changed the fuel lines and replaced the primer bulb, but I cant remember witch way the fuel lines go from the tank to the bulb and from the bulb to the tank. Your help would be greatly appreciated. Thank...


The longest, and sometimes smaller in diameter of the two Fuel Lines, goes from the bottom of the carburetor, to the bottom of the tank. (The first line will need to be longer so that you can pull it all the way through to where you put gas in.) This so that you can easily attach the fuel filter. Then pull the Fuel Line back through the hole. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank. Cut off any excess line once you know that you have enough to reach the carburetor.

The other Fuel Line goes from the primer bulb to just inside the tank,(about a 1/2 inch). (Make sure that you get the right size fuel lines.) The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the Fuel Lines through the fuel tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

Three Fuel Line Installation: In this installation, the primer bulb is separate from the Carburetor.

The (1st) Fuel Line will be the longest, and sometimes smaller in diameter of the (3) Fuel Lines. It goes from the bottom of the carburetor, to the bottom of the tank. (The first line will need to be longer so that you can pull it all the way through to where you put gas in.) This so that you can easily attach the fuel filter. Then pull the Fuel Line back through the hole. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank. Cut off any excess line once you know that you have enough to reach the carburetor.

The (2nd) Fuel Line goes from the top stem of the primer bulb to just inside the tank,(about a 1/2 inch). (Make sure that you get the right size fuel lines.) The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank. This will be the shortest of the three Fuel Lines.

The (3rd) Fuel Line goes from the bottom stem of the primer bulb to the top of carburetor

Nov 06, 2010 | Garden

1 Answer

The gas line for the in-gas filter corroded. Does it go to the pump bulb or carburator and how far down do both lines go?


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Jim

Sep 03, 2010 | Ryobi Cultivator

1 Answer

Whitch gas line from the bulb go's where


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Nov 15, 2009 | Ryobi Garden

2 Answers

Fl 1500 gas line broken where does the two lines go


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Jim

Oct 31, 2009 | Poulan Featherlite Gas Blower, with Low...

1 Answer

Craftsman 28cc gas weedeater gas line connections


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Jim

Jun 30, 2009 | Craftsman Garden

1 Answer

Need diagram on fuel lines on a 26 cc craftsman weed eater


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Jim

Jun 16, 2009 | Craftsman 25cc Gas Line Trimmer

1 Answer

Fuel filter in gas tank is attach to hose and connect to ?


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Jim

Jun 16, 2009 | McCulloch Garden

1 Answer

My homelite weed eater sx-135 the fuel filter broke of the tube


The longer, and sometimes smaller in diameter fuel line, goes from the carburetor to the bottom of the tank. This line, which has the filter attached to the end, should rest comfortably on the bottom of the tank.
The other fuel line goes from the primer bulb to just inside the tank, (about an inch, with that very small piece of plastic attached to it. This piece of plastic keeps this line from pulling out of the gas tank. this line serves as an overflow from carb.

Jim

Jun 07, 2009 | Homelite Consumer Products 4.0 Amp, 13 In....

1 Answer

32 cc Craftsman (Poulan) gas line replacement


Yes, you are right. The larger line goes to the primer bulb and only goes into the tank about an inch. The coupling just keeps the line from pulling out of the tank. The smaller line goes to the carb. This line must rest comfortably on the bottom of the tank with the filter attached to the end.

Jim

Jun 07, 2009 | Craftsman 25cc Gas Line Trimmer

Not finding what you are looking for?
2005 Honda CRF 150 F Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...