Question about 2009 Saxon Warlord

1 Answer

How to remove ring

How do I remove the retaining ring on the headwinds headlight

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Saxon Expert
  • 391 Answers

If it's the one i think it is, there is a tiny set screw in the bottom of the ring. Loosen it and twist the ring slightly and pull.

Posted on Apr 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the bulb in a headwinds headlight 6" motorcycle


Yes, loosen the retaining ring and remove the ring. The headlight is the whole bulb. Once you have the ring off, you can remove the headlight; pull it out far enough so you can get to the plug on the back of it. Disconnect the plug (just pull it straight back by the plug, not the wires). Take the bulb down you your local auto parts store and have them match up a new replacement. Install is just the reverse; connect the plug (you can test it now by turning on your lights) put the bulb back in (they do have a top and bottom, make sure to put it in with the TOP on top) put the ring around it (clamp on the bottom) and tighten the ring. Done.

Mar 31, 2014 | Headwinds 5-3/4" Standard Bullet...

1 Answer

I need instructions on how to change the headlamp bulbs on a 2005 grand marquis. Please help.


To remove first you want to remove the headlight door mounting screws and remove the headlight door. Then you want to remove the 4 retainer ring screws and remove the retainer ring from the headlight. Then you want to pull the headlight bulb forward and detach the wiring connector.

To install you first want to a
ttach the wiring connector to the headlight bulb and place the bulb in position, locating the bulb glass tabs in the positioning slots. Then you will attach the bulb retainer ring to the assembly with the retainer ring screws. Then you will install the headlight door and secure with the screws. Then you will check the headlight bulb aim and adjust as necessary

Let me know if this helps you.

Mar 07, 2011 | 2005 Mercury Grand Marquis

1 Answer

Removing and reinstalling a new headlight assembly in a 95 jeep grand cheerokee


LIGHTING Headlights REMOVAL & INSTALLATION Cherokee, Wagoneer and Comanche Models Fig. 1: Remove the top corner headlight bezel mounting screw 91076p12.jpg
Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws 91076p13.jpg
Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws . . . 91076p27.jpg
Fig. 4: . . . then carefully pull the headlight bezel away from the headlight assembly 91076p11.jpg
Fig. 5: Remove the 4 headlight assembly retaining ring screws . . . 91076p07.jpg
Fig. 6: . . . then pull the retaining ring off of the headlight assembly 91076p06.jpg
Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight 91076p28.jpg
  1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring.
  2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle.
  3. Install the headlight in the reverse order of removal.
Grand Cherokee and Grand Wagoneer Models
  1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly.
  2. Rotate the lock ring 1?8 turn counterclockwise and pull the bulb straight out from the housing. To install:
  3. Install a new bulb and position the bulb assembly in the lamp housing.
  4. Rotate the lock ring 1?8 turn clockwise to secure.
----
The Grand Cherokee will have an assembly that is fastened with bolts and screws to the body.
Get the new assembly and compare to the old one to see where to unfasten the bolts and other fasteners to aid in removing quickly.

Oct 08, 2010 | 1995 Jeep Grand Cherokee

1 Answer

I have a front headlight out on my 1998 Mercury Mountaineer. Can I replace the bulb only or do I need to replace the entire headligjt?


according to the book, you have sealed beams--one piece:
To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Sep 28, 2010 | Mercury Mountaineer Cars & Trucks

1 Answer

How do i replsce s headlight on a 1983 Omega?


PLEASE DON'T FORGET TO RATE!

  1. Remove the headlamp trim panel (grille panel) attaching screws.
  2. Remove the four headlamp bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlamp aiming screws, at the top and side of the retaining ring, or the headlamp aim will have to be readjusted.
  3. Pull the bulb and ring forward and separate them. Unplug the electrical connector from the rear of the bulb.
  4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and install the ring and bulb. Install the trim panel


addf3bf.jpg To remove the headlights, unfasten the retaining screws, then remove the headlight trim


48161cd.jpg Remove the 4 headlight retaining ring screws (A). Do not confuse these with the aiming screws (B)


801c856.jpg Remove the headlight retaining ring, but make sure the headlight doesn't fall out of the assembly


c776dce.jpg Pull the headlight out of the mounting plate, unplug the electrical connector and remove the headlight

Sep 13, 2010 | Oldsmobile Omega Cars & Trucks

1 Answer

Need to remove and repair headlight motor on a 1988 corvette


REMOVAL & INSTALLATION 1984–88 Vehicles
  1. Open the hood, then turn the headlights on.
  2. Detach the headlight motor wire on the outer side of the headlight.
  3. Turn the headlights off (the disconnected light should stay open).
  4. Unfasten the 4 screws at the bezel. There are 2 at the front and 2 at the sides. Fig. 1: With the hood in the raised position, unfasten the Torx® screws from the outer side of the headlight bezel/trim piece 91036p23.jpg
    Fig. 2: You must then remove the screws from the inner side of the bezel/trim piece 91036p24.jpg

  5. Remove the bezel. Fig. 3: Remove the first of the top bezel/retaining ring screws . . . 91036p25.jpg
    Fig. 4: . . . then remove the remaining Torx® screw 91036p26.jpg
    Fig. 5: Lift the bezel/trim piece away from the headlight assembly 91036p27.jpg

  6. Remove the retaining spring by carefully using a hooked end tool, such as a cotter pin removal tool to move it to the side.
  7. Remove the headlight from the aiming pins by rotating the headlight toward the center of the car.
  8. Unfasten the 4 retaining ring screws, then remove the ring. Fig. 6: With the hood closed, you can see the 4 headlight retaining ring screws (1) and 2 aiming screws (2) 91036p28.jpg
    Fig. 7: Remove ONLY the 4 retaining ring screws, do NOT touch the aiming screws 91036p29.jpg

  9. Remove the headlight pump from the mounting bracket, unplugging the socket as you pull it away. Fig. 8: Remove the headlight away from the mounting bracket, unplugging the socket as you pull it away 91036p30.jpg
    To install:
  10. Install the headlight bulb, making sure it is plugged in properly.
  11. Position the retaining ring and secure with the 4 screws.
  12. Position the headlight into the aiming pins. Move the retaining spring back into place.
  13. Install the bezel and secure with the retainers.
  14. Turn the headlights on, then connect the headlight motor wire.
  15. Turn the headlights off. Both should lower.
  16. Close the hood. Check the aim of the headlights, and adjust if necessary.
1989–96 Vehicles
  1. Open the hood.
  2. Open the headlight door halfway. This can be done either by turning the headlight switch on, then back to the parking lamp on position, or by the manual headlamp control knob (which is located on the inboard side of the headlight door). NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
  3. Remove the screws from the front of the headlight bezel. NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
  4. Remove the Phillips head screws from each side of the headlight bezel.
  5. Remove the bezel by pulling it straight out from the engine side of the hood. Fig. 9: View of the headlight bezel mounting 91036g28.gif

  6. Unfasten the screws from the headlight retaining ring.
  7. Remove the headlamp from the assembly, unplugging the electrical connector as you are pulling it away. Fig. 10: Exploded view of the headlight assembly 91036g29.gif
    Fig. 11: Location of the headlight mounting and aiming screws 91036g30.gif
    To install:
  8. Attach the headlight electrical connector.
  9. Position the retaining ring and install the screws securing the ring to the headlight.
  10. Position the bezel in place on the headlight assembly.
  11. Install the screws on each side of the bezel and tighten to 51 inch lbs. (5.8 Nm).
  12. Install the screws on the front of the bezel and tighten to 17 inch lbs. (1.9 Nm).
  13. Cycle the headlamps, then close the hood. Check the headlight aim, and adjust if necessary.
prev.gif next.gif

Jul 07, 2010 | 1988 Chevrolet Corvette

1 Answer

How to replace the headlight on a 1987 chevy el camino


Check this GM Chevy Mid-Size Cars 1964-1988 procedure from Repair Guide...


Headlights - REMOVAL & INSTALLATION
If some or all of the headlight bulbs being replaced still operate, refer to the headlight aiming procedure later in this section to ease checking or adjustment of the headlights after installation.
  1. Disconnect the negative battery cable.
  2. Loosen and remove the retaining screws, then remove the headlight bezel from the front of the vehicle.
  3. On most models, the headlight bulb retaining ring is only held on by retaining screws. If so, remove the bulb retaining ring screws. These are the screws which hold the thin metal ring which holds the bulb against the adjusting plate. Do not touch the two headlight aiming screws, at the center of the top and side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.

One way to identify the retaining ring screws is that they will be threaded through a lip on the outer edge of the retaining ring before threading through the adjusting plate. One the other hand, the adjustment screws are threaded through the adjustment plate and a spring loaded holder underneath it.

23f036c.jpg

Fig. 1: Exploded view of a common dual headlight mounting assembly-1983 Malibu shown typical
  1. Some later model vehicles will use a spring on the retaining ring. If so equipped, disengage the spring from the retaining ring, using a cotter pin removal tool, then remove the retaining ring screws.
  2. Pull the bulb and ring forward and then separate them. Unplug the electrical connector from the rear of the bulb and remove the bulb from the vehicle.
To install:
  1. Plug the new bulb into the electrical connector.
  2. Position the retaining ring over the bulb, then install the assembly to the adjusting plate. Secure using the retaining screws and, if applicable, the spring.
  3. Install and secure the headlight bezel.
  4. Connect the negative battery cable.
f270907.jpg

Loosen and remove the headlight bezel retaining screws

55278f9.jpg

Make sure all of the screws are removed, then pull the bezel from the front of the vehicle

b98b91d.jpg

Loosen and remove the retaining ring screws

b83d4c4.jpg

Pull the retaining ring and bulb forward to separate them


5713f83.jpg

Unplug the electrical connector from the rear of the headlight


Hope helps (remember rated this).

Jul 01, 2010 | 1987 Chevrolet El Camino

1 Answer

How do i install new headlamps


  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).
  • Nov 20, 2009 | 1999 Pontiac Grand Am GT

    1 Answer

    Fender bender, bought new assembly. How to remove old for replacement? "89 seville driver side headlight.


    LIGHTING Headlights REMOVAL & INSTALLATION
    1. Unscrew the Torx retaining screws and remove the headlight bezel.
    2. Remove the headlight bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlight aiming screws, at the top and the side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.
    3. Pull the bulb and ring forward, then separate them. Unplug the electrical connector from the rear of the bulb.
    4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and then install the ring and the bulb. Install the headlight beze

    Aug 23, 2009 | 1989 Cadillac Seville

    1 Answer

    Need to remove the passenger side headlight assembly on an "06 vw touareg?


    There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
    Make sure the replacement bulb is the same type and part number as the one that is being replaced.

    To Replace:
    • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
    • Remove the retaining ring screws from one or both lights.
    • Remove the retaining rings.
    • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
    • Push the wiring connector onto the prongs at the rear of the new light.
    • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
    • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
    • Check the aim of the headlight and adjust it, if necessary.
    • Install the headlight bezel. Secure it with the retaining screws.
    • Connect the turn signal lamp wiring (if it was disconnected).
    Hope this helps!

    Mar 10, 2009 | 2006 Volkswagen Touareg

    Not finding what you are looking for?
    2009 Saxon Warlord Logo

    Related Topics:

    120 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Saxon Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4536 Answers

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    kakima

    Level 3 Expert

    102366 Answers

    Are you a Saxon Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...