Question about 2002 Harley Davidson FXST Softail Standard

1 Answer

To bleed the clutch on a 09 fxst

No clutch pressure

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 41,624 Answers

Hi Anonymous, please visit website below:
https://www.youtube.com/watch?v=wwVEz8uoJfo
Good luck

Posted on May 01, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 s 10 clutch wont catch after bleeding it replaced masre and slave clutch


Are you sure all the air is out of the system and you have a firm pedal feel. If not have a shop pressure bleed the clutch hydraulic system.

Apr 21, 2016 | Cars & Trucks

1 Answer

97 jeep Cherokee clutch will not depress to start the engine


Now you need to bleed the clutch at the clutch slave cylinder down on the transmission to restore the clutch.
Put a wrench on the bleed valve and open it, then lightly close it. Now have someone pump the clutch a couple of times to build pressure. Then while the clutch pedal is slowly pressed down open the bleed valve, then close valve as pedal gets to floor. Repeat this bleed process until a steady stream of brake fluid comes out the bleed valve. Then you should have a good clutch again.

Dec 20, 2012 | 1997 Jeep Cherokee

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

Wont go into gear


Did any fluid come out? It has to have fluid reach the slave cylinder, and when bleed valve is open and clutch is pressed, fluid should squirt out. Open the valve and pump the clutch until fluid is forced down into the slave cylinder. Keep topping up the clutch master cylinder so it won't run dry.
Post back if still having problems. There is a tool at auto parts stores for pressure bleeding brake lines and clutch lines. It forces fluid into the lines by pressure. If nothing works, your clutch master cylinder may have failed. Take the line off at the slave cylinder and see if the master cylinder is working to push fluid through the line.

May 10, 2012 | Hyundai Motor 1997 Tiburon

1 Answer

Clutch pedal has no pressure and goes straight to the floor when pressed. clutch disk is in good condition. parked the car the night before was working perfect. next morning no pressure and out of fluid....


Pump the clutch pedal and then check for leaks again, including under the dash where the rod from the pedal goes into the clutch master cylinder. Once you find the leak, replace what's leaking and bleed the system to restore the pressure (bleeds from the slave unit, just like bleeding brakes)

May 30, 2011 | 1996 Honda Civic

1 Answer

The clutch lever does not depress clutch so you can get in gear


Make sure the clutch fluid reservoir on the handlebar is full of dot3/4 brake fluid and bleed the clutch slave cylinder to get the air out. If you can not build pressure or lose pressure after bleeding, replace the seals in the master and slave and bleed again.

Oct 07, 2010 | 1986 Honda GL 1200 Aspencade Gold Wing

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

I just replaced my clutch and master clinder. and now my clutch pedal has no pressure. and how to bleed the line


The best way is by 'pressure bleeding'. Workshops have these as an every day tool, but you can do this by letting gravity do it for you. Fill the clutch resevoir right up, then open the bleed valve on the slave cylinder and let the fluid drip through until clear of all traces air, Close the bleed valve. Your clutch should work now. Do not touch the clutch pedal until the operation is completed.

Mar 18, 2010 | 1991 Saturn SL1

1 Answer

Clutch master cylinder rebuilt, brand new clutch slave installed. Still can't get pressure to come up after bleeding on my 85 FJ1100. Original lines and seal on master cylinder cover. I'm at a loss here,...


Hi there,
Some times the clutch systems needs a vacuum
pump to bleed the system up to pressure. Also
note whilst bleeding the system don't let the reservoir run out of fluid. Also check if there is any other bleed nipples in this system. They all need bleeding.Hope this helps your problem.
Regrades Lighten



Apr 26, 2009 | 1985 Yamaha FJ 1100

Not finding what you are looking for?
2002 Harley Davidson FXST Softail Standard Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4339 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...