Question about 2003 Suzuki GSX 750 F (Katana)

1 Answer

How do i install a alternator

Dont know were my wires go

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Suzuki Expert
  • 391 Answers

The three (usually yellow) wires from the alternator can hook to any of the three large wires from the regulator.

Posted on May 14, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Saturn vue V6changed the alternator- have red wire don't know where it goes could someone explain info to wiring and cable when replacing the alternator- thanks


The red wire goes to the positive on your battery.
It should conect to a post on the back of your alternator near where the wire harness plug goes into.
Sorry i dont have any diagrams or pictures.

Oct 26, 2015 | Saturn Cars & Trucks

1 Answer

Alternator wont charge


at alternator gig wire battery voltage,one wire battery volts one less . battery volts wire goes to automatic shut down relay, less then battery voltage wire to pcm fuse will be 20 amp just ck all that size.

Aug 05, 2012 | 2001 GMC Sierra 2500HD

1 Answer

Batter wont charge, jeep idles for about a min then dies. Need to replace alternator, but dont know how


I have the same Jeep model 5.2L V8, to replace the alternator, check the next procedure...

Once the determination is made that the alternator is at fault, off vehicle testing can be used to determine the defective component inside the alternator.
See Figures 1 through 11
  1. Disconnect the negative battery cable.
  2. Remove the drive belt.
  3. If necessary, remove any splash shielding for easier access to the alternator.
zjlimited_482.jpg

Fig. 1: For easiest access to the alternator assembly, first remove the splash shield mounting fasteners ...

zjlimited_483.jpg

Fig. 2: ... then swing it out of the way for access to the alternator assembly

zjlimited_484.jpg

Fig. 3: View of the alternator electrical connections-(A) battery positive, (B) field terminals, (C) wire harness hold down, (D) ground terminal

  1. Tag and disengage the alternator wiring.
It may be necessary to remove the alternator and mounting bracket from the vehicle as an assembly.
  1. If equipped, remove the front alternator assembly mounting plate.

zjlimited_485.jpg

Fig. 4: Remove the six nuts and bolts that secure the front mounting plate to the alternator assembly

zjlimited_486.jpg

Fig. 5: Remove the front alternator assembly mounting plate from below the vehicle

  1. Unfasten the alternator mounting and pivot bolts and remove the alternator.
  2. If installing the original alternator assembly, push out the pivot bushing as illustrated.
zjlimited_487.jpg

Fig. 6: After removing the alternator assembly front mounting plate, remove the front engine-to-alternator bracket mounting stud

zjlimited_488.jpg

Fig. 7: Remove the two alternator bracket-to-engine mounting bolts

zjlimited_489.jpg

Fig. 8: Remove the alternator and mounting bracket assembly from the vehicle



To install:

  1. Mount the alternator to the brackets with the nuts and bolts. Tighten the two mounting bolts and nuts to 40 ft. lbs. (54 Nm).
  2. If the alternator and mounting bracket were removed as an assembly, install the assembly into the vehicle.
  3. If removed, install the front mounting plate.
  4. Engage the alternator electrical connections.
  5. If removed, install the splash shield.
  6. stall the drive belt and attach the negative battery cable.

Hope this helps (remember to rate and comment this answer).

Jan 16, 2011 | 1994 Jeep Grand Cherokee

1 Answer

Oldsmobile alternator doesn't work after starting car.. Replaced both alternator and battery atleast 2 times already.. Don't know what the problem is. Checked all fuses, wires, stereo, grounds, etc. Read...


THE RED SMALL POSITIVE BATTERY FEED WIRE COULD BE BROKEN THAT GOES TO BACK OF ALTERNATOR.CHECK TO SEE IF POWER GOING TO THE WIRE.IT NOT POSITIVE BATTERY SMALL FEED CABLE BROKEN.OR YOU HAVE BLOWN FUSE LINK.IF ALL IS GOOD YOU COULD HAVE PCM PROBLEMS YOUR FIELD CONTROL CIRCUIT PART OF THE PCM CIRCUIT.HAVE VECHICLE SCANNED TO LOOK FOR ALTERNATOR PCM FAULT. AFTER YOU INSTALL NEW ALTERNATOR DONT CRANK THE CAR UNTIL YOU GET A SCANNER AND ERASE TROUBLE CODE FIRST BECAUSE THE PCM THINK OLD ALTERNATOR STILL IN VECHICLE AND WILL CAUSE CHARGING PROBLEMS.

Dec 29, 2010 | 2003 Oldsmobile Alero

1 Answer

How can i remove the alternator from a 2002 gmc safari i allready remove the air filter but i dont know how to loose the band?


use a ratchet without any socket on the idler/tensioner pulley, this will loosen the tension on the belt to be able to remove it. after that, it's easier to remove the alternator with the braket still on, that bracket has a few long bolts 3-4 to remove, the, disconnect wires from alternator. installation is reverse procedure as always

Jun 16, 2010 | 2002 GMC Safari

2 Answers

Wont hold charge in expedition


  1. Check the wiring of the new radio installed as follows..
  2. Disconnect battery ground
  3. verify radio ground wire is grounded to metal
  4. verify radio hot wire (normally red and thick) is connected to a power source that is off when the ignition key is in the "off" position.
  5. verify that the always hot wire is connect to a constant 12v power supply even with the ignition off.
  6. make sure the pwr antenna wire if not used is taped at the tip and not touching any metal.
  7. verify that all speaker wires are connect correctly and not shorted to ground.
  8. connect battery ground you may get a small spark if your courtesy lites work.
  9. start engine verify your battery is charging by disconnecting the battery ground cable while the engine is running, it should continue running if it don't, alternator maybe bad.
  10. If it continues running problem solved..

Nov 11, 2008 | 1987 Ford F 350

1 Answer

Trying to install triple gauge water oil amps


if I remember right the alternator has a large red wire on the back that goes to the battery ,it goes in it just cut and run two wires to the amp gauge must be the same size as the wire you cut 10 gauge I beleive

Sep 22, 2008 | Measuring Tools & Sensors

Not finding what you are looking for?
2003 Suzuki GSX 750 F (Katana) Logo

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...