Question about 2005 Suzuki Boulevard S40

Open Question

Change spark plug remove seat - 2005 Suzuki Boulevard S40

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hesitating on a 2006 Buick Lacrosse


this is for a 3.6L engine, should be the same either way. doesnt seem extremely difficult

  1. Turn the ignition OFF.
  2. Remove the ignition coil.
  3. Use compressed air in order to remove debris from the spark plug cavity.
CAUTION: Refer to Safety Glasses and Compressed Air Caution in Service Precautions .

NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
  1. Remove the spark plug.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug threads to seize, causing damage to cylinder head threads.

INSTALLATION PROCEDURE
  1. Ensure that the spark plug gap is equivalent to the spark plug gap specification. Refer to Ignition System Specifications.
NOTE:
  • Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  • Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the engine.
  1. Install the spark plug.
NOTE: Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary, to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or thread damage.

Tighten the spark plug to 20 N.m (15 lb ft) .
  1. Install the ignition coil.


26252193-gjaozkvamcccpvfgr5edjxnv-1-0.gif

Aug 04, 2016 | 2006 Buick LaCrosse

1 Answer

What is the best way to change the spark plug? And


follow this u-tube link for the seat , the plug just needs a correct plug socket ( different bike but same routine)
How to remove seat and charge the battery on Honda CB250 NightHawk

Oct 05, 2014 | Cars & Trucks

1 Answer

How to change spark plugs



REMOVAL PROCEDURE
  1. Remove the ignition control modules.
  2. Clean the spark plug recess area with low pressure air.
CAUTION: Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury.

NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
117381099
  1. Remove the spark plugs from the cylinder heads.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug threads to seize, causing damage to cylinder head threads.
  1. Inspect the spark plugs. Refer to Spark Plug Inspection.
INSTALLATION PROCEDURE
  1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement to the gap specifications.
NOTE:
  • Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  • Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the engine.
117381099
  1. Install the spark plugs to the cylinder heads.
NOTE:
  • Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary, to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or thread damage.
  • Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 20 N.m (15 lb ft) .
  1. Install the ignition control modules.

Jul 14, 2014 | 2006 Cadillac SRX

1 Answer

How do I change spark plugs in 1995 Mitsubishi Mirage?


Those shouldn't be too hard to change.
You'll need:

3/8 drive ratchet
6 inch extension
5/8 inch spark plug socket
gap tool for spark plugs (Autozone usually has them at the counter)
anti seize compound
torque wrench for tapered seat spark plug (beam style)

First you need to remove the spark plug wires from end of the spark plugs. To remove a wire/boot grab the boot at the top and twist it a couple of times to break the boot loose from the plug. Don't pull the boot out by the wire. Once it is loose pull up on the boot to remove the wire/boot. Take note of which wire goes where. If you have any damaged wires, wires that have white flash burns, boots that are contaminated with engine oil, or boots that are damaged you should replace the wires/boots as a set.

Put together your ratchet, extension, and socket. Remove the spark plugs by turning CCW.

Using the gap tool make sure that the gaps are set correctly on your plugs. All platinum and iridium plugs come pre-gapped and should be inspected before you purchase them at the counter. The gap specifications should be on the underhood sticker. It is probably .044 inch. If they are platinum or iridium plugs, it isn't recommended to use a coin or wire gap tool because you may damage the center electrode or ground strap points.

Apply a tiny amount of anti seize to the spark plug threads. The anti seize will aid in installation and removal later on. Carefully tighten the spark plug. If the plug you are installing is equipped with a crush washer, seat the plug, then tighten about 1/4 turn to crush the washer. If you are installing a tapered seat plug, tighten the plug with a torque wrench to specifications provided by the vehicle or plug manufacturer.


Custom Car Body Kits


Jun 15, 2012 | 1995 Mitsubishi Mirage

1 Answer

How do you change the spark plug on the 2003 yamaha 450


Remove seat - Remove Tank - Remove spark plug coil (just pulls off) Then with correct spark plug wrench you can undo the spark plug and replace with new one( dont feel the need to over tighten the new plug just tight is fine!) Then push coil all the way back on - install the tank and then install the seat - Ready to go!
good luck regards Jamie

Jan 07, 2011 | 2003 Yamaha YZ 450 F

1 Answer

How do i change my spark plugs on suzuki c50 motorcycle


No. 1 (FRONT) SPARK PLUG REMOVAL
• Remove the rear and front seats.
• Remove the fuel tank.
• Remove the right frame cover 1 (remove hooked part)
• Remove the spark plug cap
• Remove the spark plug with a spark plug wrench.
No. 2 (REAR) SPARK PLUG REMOVAL
• Remove the rear and front seats.
• Remove the fuel tank.
• Remove the spark plug cap.
• Remove the spark plug with a spark plug wrench
Hope this help you quest. Good enough?

Apr 18, 2010 | 2005 Suzuki Boulevard C50

1 Answer

Change plugs 1700 roadstar


There is a tool pouch under the seat...In it there is a tool for removing the spark plugs..

I would recommend that you at least remove the gas tank...It'll make it a little easier to remove and replace the plugs. But, before you remove the plugs...Take an air compressor with a blow gun and blow out the spark plug ports, so no dirt or debris gets into the cylinder. Remove one spark plug wire at a time...Blow the port out...Then remove the plug...Check it and if it's good, re-check the gap and reinstall the plug...Put the wire back on and move to the next plug. Repeat the above...

Make sure you don't cross-thread the plugs when you reinstall them...Make sure the wires are firmly on the plugs...And make sure you put the right wire on the right plug, which shouldn't be a problem if you only remove one at a time.

And also make sure when you reinstall the gas tank that the fuel lines are firmly seated...

Removing and replacing your spark plugs is fairly easy.

Dec 18, 2009 | 2003 Yamaha Road Star Warrior

1 Answer

Where are the spark plugs on my 2000 Oldsmobile Intrigue and how do i change them?


2000 Oldsmobile Intrigue V6-214 3.5L VIN H SFI

Spark Plug: Service and Repair
REMOVAL PROCEDURE
TOOLS REQUIRED
J 43094 Spark Plug Boot Puller
1. Turn OFF the ignition switch.
2. Remove the ignition coil assembly.
3. Use the J 43094 in order to remove the spark plug boots from the spark plugs.
NOTE: Allow the engine to cool before removing the spark plugs. Attempting to remove the spark plugs from a hot engine may cause the plug
threads to seize causing damage to cylinder head threads.
NOTE: Clean the spark plug recess area before removing the spark plug. Failure to do so could result in engine damage because of dirt or
foreign material entering the cylinder head, or by the contamination of the cylinder head threads. The contaminated threads may prevent the
proper seating of the new plug. Use a thread chaser to clean the threads of any contamination.
4. Remove the spark plugs from the engine.
INSTALLATION PROCEDURE
NOTE: Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the
vehicle. Installing spark plugs of another type can severely damage the engine.
NOTE: Check the gap of all new and reconditioned spark plugs before installation. The pre-set gaps may have changed during handling. Use a round
feeler gage to ensure an accurate check. Installing the spark plugs with the wrong gap can cause poor engine performance and may even damage the
engine.
1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement to the gap specifications. Refer to Spark Plug Usage.
Correct as necessary.
NOTE: Be sure that the spark plug threads smoothly into the cylinder head and the spark plug is fully seated. Use a thread chaser, if necessary,
to clean threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or
thread damage.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the spark plugs to the engine.
Tighten
Tighten the spark plug to 20 N.m (15 lb ft).
3. Install the spark plug boots to the ignition coil assembly.

5c212b8.jpg
4. Install the ignition coil assembly.

Sep 13, 2009 | 2000 Oldsmobile Intrigue

2 Answers

How much of the Suzuki C90 Boulevard do I have to disassemble to change the spark plugs?


Take the tank sides off and then the chrome covers over the spark plugs. The genuine spark plug tool that came with your bike works well to remove the plugs.

There is no need to remove the seat, instrument cluster or airbox.

Jun 25, 2009 | 2005 Suzuki Boulevard C90

1 Answer

HOw to get into engine to change spug pluggs and leads for Toyota estima 1993


The best thing to do is to purchase a Haynes manual for the Toyota Previa. But to access the spark plug wires and spark plugs you will need to remove the passenger front seat. This requires taking out four bolts on the four corners of the seat. After the seat is removed you need to remove the outside seat support and the jack and jack handle that is located under the seat. Next remove the bolt from the seat belt/shoulder harness. Romove the screws from the side of the carpet keeper strip along the bottom of the door. carefully, using a flat blade screwdriver, pry the plastic carpet strip up carefully disengaging it from the rear strip. Unhook the carpet from the edge of the doorway. Pull the carpet back enough to expose the bolts holding the cover over the engine. Remove all the bolts holding the cover over the engine. This will expose the engine head. remove the three bots holding the black plastic cover over the spark plug wires. This wires can be removed allowing access to the plugs. Be aware these engines use only platinum tipped spark plugs. Good Luck

Nov 21, 2008 | 1993 Toyota Previa

Not finding what you are looking for?
2005 Suzuki Boulevard S40 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...