Question about 2008 Harley Davidson FLHTC Electra Glide Classic

1 Answer

Wont go over 1100 rpm - 2008 Harley Davidson FLHTC Electra Glide Classic

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Harley Davidson Master
  • 43,716 Answers

Hi Anonymous, your ECM detected a malfunction and went into limp mode. Please visit websites below:
Sudden limp mode Harley Davidson Forums Harley Davidson Motorcycle Forum
Limp mode check engine light on Harley Davidson Forums HDTalking com
Good luck

Posted on May 01, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Carb issue if the ignition system checks out ok. Just had this same issue with a mercury 150. One of the three carbs had a sticky needle valve.

Aug 16, 2016 | Boating

1 Answer

What are the torque specs on fj 1100

Max Torque 86 Nm / 64.2lb / ft @ 8000 rpm

Max Power 125 hp / 91.1 kW @ 9000 rpm

Sep 01, 2014 | 1984 Yamaha FJ 1100

1 Answer

How to check rpm on v star 1100

Hi, Anonymous you need to install a tachometer or have an electronic diagnostic meter that is capable of measuring RPM'S for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Tach Install Star 1100
What 900 RPM sounds like
OEM parts for Yamaha

Sep 29, 2013 | 2001 Yamaha V Star 1100 Classic

1 Answer

My 2005 650 vstar wont accelaerate in 4th and 5th gear and loses power going up has plenty of acceleration in 1st 2nd and 3rd gear...wont go faster than 65

Had same problem with my sons 2000 1100. Was told by mechanic that the High RPM Jet was clogged and to clean carb. I filled the tank, put 1/3 of a can of Seafoam carb/injector cleaner, by the end of the week it was running 100 mph again.

Feb 04, 2013 | 2001 Yamaha V Star 1100 Classic

1 Answer

I have a primary jet and secondary jet in the carburator of the 500 gl silverwing . and the jets I have is 75 and 125 which goes where . and what should be the setting on the air jet ?

The secondary main jet (125) goes into the jet needle holder in the center of the carb (needle). The primary main jet (75) is between the secondary main jet and the pilot screw (this one is slightly off center) . The start setting for your air screw should be 1 3/4 turns. Warm up your engine and drive for ten minutes. Adjust your idle speed to 1100 + or - 100 rpm. Now turn pilot screw in or out to get highest idle speed. Readjust idle to 1100 rpm. Now turn pilot screw in till idle speed drops 100 rpm. If pilot screw seats go to next step. Adjust the pilot screw out 1 full turn from 100 rpm drop point. Now reset Idle to 1100 rpm. That is how Honda says to set your air screw. Standard setting is probably sea level and going through the procedure will set you up for the altitude where you ride. Do the adjustment during good weather at the altitude you plan to do the most riding.

Aug 27, 2010 | Honda CX 500 B Motorcycles

1 Answer

What should a 2000 s-10 4.3 idle at? how many rpm?

650 RPM warm
About 1100 RPM cold

Both can vary by about 50 RPM and still be ok.

Nov 22, 2009 | 2000 Chevrolet S-10

1 Answer

92 chevy truck 5.7 idle revs up and down high emissions

sounds like a vacuum leak check hoses and manifold

Mar 21, 2009 | 1991 GMC K2500

1 Answer

Servis washing machine fills but wont turn

is it a brush motor? if so the brushes may be worn, secondly the motor control pcb may have blown. also check the wiring.

Mar 18, 2009 | Washing Machines

Not finding what you are looking for?
2008 Harley Davidson FLHTC Electra Glide Classic Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

4340 Answers


Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides