Question about 2006 Yamaha Warrior

1 Answer

Engine clutch vibrating noise when clutch is almost fully released

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Yamaha Expert
  • 391 Answers

Clutch is probably "chattering" due to wear. Probably needs clutch discs and be sure the steel plates are checked for flatness.

Posted on Apr 13, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch noise


Bearing noises in a clutch system are easily distinguished by running a few simple tests. Start the engine and leave the transmission in neutral. If a transmission makes noise when it is in neutral it is often a worn input shaft bearing. Now depress the pedal until the clutch just engages. This is the point where the release bearing is just contacting the pressure plate fingers. If you begin to hear a squealing sound this is likely a worn release bearing. If a whirling noise is present when the clutch pedal is fully depressed it is probably the pilot bearing.

Jun 09, 2014 | BMW 316i Cars & Trucks

1 Answer

Vibration through clutch pedal polo 59hp 2011


This is caused in most cases by a worn out clutch pressure plate release bearing. To replace this bearing the transmission must be removed from the car. You will also likely need to have the clutch replaced and the flywheel machined smooth well it is all apart. About $700.00-$1000.00 for the complete job

Jul 05, 2012 | Cars & Trucks

1 Answer

Clutch noise and vibration when fully pressed


This is caused by a defective clutch pressure release bearing, the release bearing is the only part that can cause this symptom. To replace the clutch release bearing requires the transmission be removed from the car, the release bearing rides on the input shaft collar of the transmission input shaft which goes into the clutch disk. If you replace the release bearing you should have the clutch disk and pressure plate replaced at the same time as the labor cost is about the same just to do the bearing.

Oct 31, 2011 | 2008 Volvo V50

1 Answer

Hard to press clutch pedal


Hi, if its a cable clutch , replace the cable with a new one etc. is there a winning noise from the back of the engine with the clutch depressed, if so , could be the release bearing that's the problem, you might get some vibration through the clutch pedal if this is the case, good luck.

Feb 22, 2010 | Ford Escort Cars & Trucks

1 Answer

I have an 1989 GMC Sierra K1500(4x4)5-speed. grinds when going...


It may be the transmission input shaft bushing or bearing, located in the rear of the engine crankshaft, in front of the clutch assembly. If the bushing or bearing is dry (needs to be greased), the input shaft will still try to turn with the engine rpm, even though the clutch pedal is depressed. Also, the clutch disc may not be fully releasing, which could possibly be corrected by adjusting the clutch pedal linkage. good luck

Jul 26, 2017 | GMC Sierra 1500 Cars & Trucks

1 Answer

Gear shifting


Adust clutch cable.Test...start the car in first gear with clutch fully depressed, parking break off. Slowly release the clutch. determine when the vehicle starts to move. If clutch is fully depressed call that 100%, fully released is 0%. The vehicle should be moving at around the 55-45% range.

Dec 02, 2009 | 2002 Nissan Xterra

1 Answer

2001 BMW 330i clutch vibration


u have a worn out clutch pressure plate release bearing, that is what u feel and hear..

Dec 22, 2008 | 2003 BMW 330

1 Answer

Is it my clutch or gearbox or something else


hi sounds like the clutchs release bearing when you press the pedal noise the noise appeared but when in neutral noise is not there this is second one tonight with simular problems for this year and model yates210456

Sep 29, 2008 | 2000 Ford Escort

2 Answers

Gearbox from clutch


have you checked the clutch mechanism? for me sounds like the clutch doesn't engage properly or fully rather. Ask your mechanic to check the clutch system fully and check whether it fully engages, or do this check for yourself. Bring car onto a flat surface and shift to 1st while engine being switched off, start it while pressing the clutch (fully down to the floor board) and then release parking break and check for following
whether vehicle is moving
RPM decreases a bit
does engine get loaded and start vibrate or rattle a bit

Jun 07, 2008 | 1987 Peugeot Liberte

Not finding what you are looking for?
2006 Yamaha Warrior Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...