Question about 2001 Suzuki VL 1500 Intruder LC

Open Question

BMW k1300s torque settings

Brake caliper

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

What size allen wrench do i need for the front brake calipers


For front brake pads replacement you only need usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
Instructions for front brake pads replacement.
For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing.

Important note: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!
Check brake fluid level and top up as neccessary!

Sep 03, 2011 | 1994 Audi 100

1 Answer

What tool is needed to remove the caliper, a hex key or something else?


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservoir, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!
Check brake fluid level and top up if neccessary!!!

Jul 22, 2011 | 1996 Audi A6

1 Answer

Remving caliper pins on 2000 vw jetta and caliper


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Jun 26, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

I want to change my front brake pads How do I remove the old ones


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Apr 12, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

What size bolt holds the brake and caliper on a 99 Volkswagon Passat


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Mar 27, 2011 | 1999 Volkswagen Passat

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

How do I replace the ear brakes?


Bonneville, LeSabre, Park Avenue 2000-2005

Brake Caliper - Removal & Installation

CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.
Inspect the fluid level in the brake master cylinder reservoir. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
  1. Raise the vehicle and suitably support.
  2. Remove the tire and wheel assembly.
  3. Pull down on the front park brake cable.
  4. Remove the front park brake cable from the park brake cable connector.
    NOTE When using a large C-clamp to compress a caliper piston into a caliper bore of a caliper equipped with an integral park brake mechanism, do not exceed more than 1 mm (0.039 in.) of piston travel. Exceeding this amount of piston travel will cause damage to the internal adjusting mechanism and/or the integral park brake mechanism.
  5. Install a large C-clamp over the top of the brake caliper housing and against the back of the outboard brake pad. Compress the brake caliper piston into brake caliper bore to allow the piston enough clearance to slide the brake caliper off the brake rotor.
  6. Remove the C-clamp.
    NOTE Be sure to plug the opening in the brake caliper and brake hose to prevent fluid loss and/or contamination.
  7. Remove brake hose to caliper bolt attaching the brake hose to the brake caliper.
  8. Remove the brake hose from the brake caliper.
  9. Remove and discard the two copper brake hose gaskets. These gaskets may be stuck to the brake caliper and/or the brake hose end.
  10. Remove the park brake cable bracket from the brake caliper. Leave the park brake cable attached to the cable bracket.
  11. Disconnect the park brake cable from the park brake lever on the brake caliper.
  12. Remove the lower brake caliper pin bolt.
  13. Rotate the brake caliper up.
  14. Remove the brake caliper from the upper brake caliper pin bolt.
To install:
  1. If reusing the brake caliper retainers, clean the sleeves using denatured alcohol, or equivalent.
  2. Lubricate the brake caliper pin bolts with a thin coat of high temperature silicone lube.
  3. Install the brake caliper to the upper caliper pin bolt.
  4. Rotate the brake caliper down over the brake pads into the brake caliper bracket.
  5. Install the brake caliper pin bolts. Tighten the brake caliper pin bolts to 27 Nm (20 ft. lbs.).
  6. Remove the plugs in the brake hose end.
    NOTE Install NEW copper brake hose gaskets.
  7. Assemble the brake hose bolt and the NEW copper brake hose gaskets to the brake hose.
  8. Install the brake hose to caliper bolt to the brake caliper. Tighten the brake hose to caliper bolt to 44 Nm (33 ft. lbs.).
  9. Connect the park brake cable to the park brake lever on the brake caliper.
  10. Install the park brake cable bracket to the brake caliper. Tighten the park brake cable bracket bolt to 43 Nm (32 ft. lbs.).
  11. Install the front park brake cable to the park brake cable connector.
  12. Bleed the brake system.
  13. With the engine OFF, gradually apply the brake pedal to approximately 2 / 3 of its travel distance.
  14. Slowly release the brake pedal.
  15. Wait 15 seconds, then repeat until a firm brake pedal is obtained. This will properly seat the brake caliper pistons and brake pads.
  16. Install the tire and wheel assembly.
  17. Lower the vehicle.

NOTE The Bosch 2U ABS system cannot increase brake pressure above master cylinder pressure applied by during braking. There is no need to depressurize the system prior to service.
  1. Remove brake fluid from the master cylinder reservoir until the reservoir is approximately 1 / 3 full.
  2. Remove the front wheel. Mark the position of the wheel to the wheel studs, prior to removal, for installation reference.
  3. Install 2 lug nuts to retain the rotor once the caliper is removed.
  4. Using a large C-clamp, bottom the piston in the caliper bore by positioning the C-clamp on the outboard pad and on the round portion of the brake caliper where the piston is housed.
  5. Remove the banjo bolt that fastens the brake hose to the brake caliper. Discard the gaskets.
  6. Cap the brake line to avoid excessive fluid loss or fluid contamination.
  7. Remove the rubber dust boots from the caliper mounting bolt heads (if equipped).
  8. Remove the caliper mounting bolts.
  9. Remove the park brake cable from the caliper.
  10. Remove the caliper from the vehicle.
  11. Remove the brake pads.
To install:
  1. Install the brake pads. Lubricate the slides where the caliper mounts on the steering knuckle with silicone grease.
  2. Install the caliper over the rotor.
  3. Install the caliper mounting bolts. Torque the mounting bolts to 38 ft. lbs. (51 Nm).
  4. Install the park brake cable.
  5. Install the rubber dust boots over the caliper mounting bolt heads (if equipped).

    542f486.jpg
    Fig. Measuring the caliper clearance
  6. Check the clearance between the brake caliper and caliper bracket stops. If the clearance is too tight, check the caliper leading and trailing edges for build up. File down as necessary.
  7. Connect the brake hose to the caliper. Install the brake hose banjo bolt, using new gaskets, and torque to 33 ft. lbs. (45 Nm).
  8. Remove the lug nuts used to secure the rotor.
  9. Install the wheel, aligning the reference marks made during removal, and torque the lug nuts to 100 ft. lbs. (140 Nm).
  10. Refill the master cylinder and bleed the brake system using the recommended procedure.
  11. Road test the vehicle and check for proper braking performance

Hope helps (remember rated this).

Jul 08, 2010 | 2003 Pontiac Bonneville

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    1 Answer

    WHAT TOOLS ARE NEEDE TO REPLACE AUDI A3 SPORTSBACK FRONT BRAKE PADS


    For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. You must buy the brake pads with wear sensor. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
    1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
    2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
    3. Now you must thoroughly clean the brake calipers (free of grease).
    4. Remove outer brake pad from brake carrier.
    5. Pull inner brake pad out of brake caliper piston.
    6. Check up the brake fluid level on the reservor, and emptying if neccessary!
    7. Push piston back into brake caliper housing.
    8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exists, must point in direction of brake disc rotation when vehicle is moving forward).
    9. Install outer brake pad into brake carrier.
    10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
    11. Install both caps.
    12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

    Feb 14, 2010 | 2006 Audi A3

    Not finding what you are looking for?
    2001 Suzuki VL 1500 Intruder LC Logo

    Related Topics:

    107 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4514 Answers

    Ed Nelson
    Ed Nelson

    Level 2 Expert

    149 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...